Kohler PURIST 24982T-4 User manual

1431501-2A-A 1
1431501-2A-A 4
254
G1/2˝
608
212
495
99
Ø33.5~Ø40
180
Max. 53
Ø57
**Color code must be specified when ordering.
NOTE: For all Asia pacific regions (excluding China) add SP (SPxxxxxxx**) in front of the part number when ordering.
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTE:
1. Flush the water supply pipes thoroughly to remove debris.
2. For new installations, install the faucet to sink before installing.
3. The highest working pressure for spray is 0.5MPa(5bar). If it exceeds 0.5MPa(5bar), a pressure reducer is
needed. The highest water and environment temperature is 60ºC. Please keep spray from heater, or it may
become damaged and cause injury to the user.
STANDARD APPLICABLE
Special model meets or exceeds the following at date of manufacture: TIS
24982T-4 Semi-Pro Kitchen Faucet24982T-4 Semi-Pro Kitchen Faucet
ROUGH-IN DIMENSIONS
INSTALLATION INSTRUCTIONS
PURISTPURIST
SERVICE PARTS
600
1327995**
1261398
1261395**
1327996
1414958**
1327997**
1281802
1236110
1261384
1414959
1268159
1268161
1261736
1261737
1261392
1328001 1317548
1414963
1414964
1412657**
1412658
1281262
1261872
1339320
1309222
1327981
1259352
880096
1328000**
1339318
1431513**
1292054
1309217
1309215**
1424433

2. Partially thread the screws(1) into the ring(2).
3. Slide the washers(3,4) onto the shank(5) and thread
the ring onto the shank.
4. Tighten the screws to fix the faucet.
5. Connect the hoses(6) to water supplies. The hose
with “COLD” label(7) should be connected to cold water
supply.
1
4,Metal
3,Rubber
2
5
Faucet Maintenance:
With the water running, rub the nozzles to dislodge
debris.
To improve the flow, disconnect the spray(8) and clean
the screen washer(13). Reassemble.
Turn on the handle gently. Turn clockwise for cold water,
turn counter-clockwise for hot water.
Press the button(11), the water flow is as figure B shown;
Press the button(12), the water flow is as figure A shown;
Press and hold the button(10), it will increase water flow.
A B
1431501-2A-A 3
1431501-2A-A 2
8
9
1111
12 12
10
8
13
"LEAD FREE" is marked on the back of the faucet signifying its compliance with the United States AB1953
INSTALLATION CHECKOUT
Ensure that all coupling nuts are tight. Ensure that the handle is in the off
position. Check for leaks. Repair as needed.
Unscrew the spray(8). While rotating the handle, flush the hot and cold water
for about one minute. Reinstall the spray into the hose(9), adjust the hose and
make spray hook in the positon of bracket.
OPERATION INSTRUCTION
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
INSTALLATION
1. Slide the base over the shank until it is against the
faucet bottom. Insert the faucet assembly into the hole,
and make sure the handle is on the right side.
Base
67
Hot
Cold