Kohler BEITOU User manual

1261813-IN2-A 1
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. Inspect the supply tubing for damage and leakage. Replace and maintain as necessary.
3. Observe local plumbing codes.
4. Check for leaks before cover the pipes, repairs as needed.
5. Please ensure only apply water pressure test on the product, and empty the air in pipe and faucet thoroughly
before the test. Please ensure test pressure below 0.8MPa (8 bar) and test duration within 30 minutes.
1261813-IN2-A 4
INSTALLATION INSTRUCTIONS
99876IN-4ND Wall Mount Lavatory Faucet
99876IN-4ND Wall Mount Lavatory Faucet
BEITOUBEITOU
HANDLE OPERATION
Lift handle gently. Turn clockwise for cold water, turn counter-colckwise for hot water.
STANDARD APPLICABLE
Special model meets or exceeds the following at date of manufacture: TIS
ROUGH-IN DIMENSIONS
SERVICE PARTS
**Color code must be specified when ordering
94
135
G1/2˝
47~57 70
167105
233
59
46
27
1111496
1223368
1080817
870654
3010643
1228823
1244920
1234006**
1180881
20960
870992
1234010
1234011
1234012
1234003
1223584
1223593
1223587**
1223586
1228835**
1231860
1234008
1241100**
1228832
1231859
3015832
3016092
3010849

1261813-IN2-A 2 1261813-IN2-A 3
INSTALLATION
How To Install The York
Do not take off guards(1) at this moment.
Determine where the york(2) will be located on the wall according to the
lavatory.
Connect the G1/2˝ supplies to the york. Please note that the side of the york
with red dot connects to the hot supply and towards right. The distance between
finished wall and supplies should be 47~57mm. Ensure that the gaps between
guards and finished wall are less than 5mm.
Increase hot and cold water supply pressures to 1MPa. Inspect for leaks.
NOTE: Make sure two guards are the same distance to the wall. Ensure the
centerlines of them are horizontal.
COLD
HOT
INSTALLATION CHECKOUT
Ensure that all connections are tight. Ensure that the handle is in the off
position.
Turn on the main water supply, and check for leaks. Repair as
needed.
CLEANING INSTRUCTIONS
CARE AND MAINTENANCE
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
Clean Rectifier and Aerator
If there is a lot of debris in the supply pipes or the quality of water is bad, it will
cause the flow in bad condition. Please clean the filter and aerator as following
steps:
Turn off the faucet. Take out the plugs(15). Remove the screws(17) with hex
wrench(16). Uninstall the spout(18) from body(4). Remove the insert(19) and
rectifier(20). Remove the aerator(22) by tool(21).
Flush the filter of rectifier and aerator. Check the filter and aerator whether is
intact, if damaged replace it.
Reassemble the spout and body: put the insert, rectifier and aerator into the
original position. Install the spout onto body and tighten the screws. Insert the
plugs.
1
2
2
1
47~57mm
5mm Max.
18
17
16
4
19
20
22
21
15
How To Install The Faucet
When the finished wall is completed, cut off the exposed guards from the
finished wall.
Shut off water supply. Remove plug(a) from base. Install two inlets(3) into two
holes of the body(4). Tighten two screws(5) to secure the body.
3
4
5
a