Kohler LOURE K-98454T-B-CP User manual

All information is based on the latest product information
available at the time of publication, Kohler Co. reserves
the right to make changes in product characteristics,
packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They
contain important installation, maintenance and cleaning
information.
所有的资料是按最新出版的产品资料编写而成。
科勒公司保留任何时候不经通知即可改变产品特
性、包装或产品可供类型的权利。
说明书包括重要的安装、保养及清洁方面的内容，
请把这些资料交给用户阅读。
1. 一定要先彻底冲洗供水管以清除管道中的杂
5. 对于直流龙头， 安装时注意电池的正负极不
能装反，电池盒盖要拧紧，防止电池受潮。
6. 对于交流龙头，安装时务必按照说明书的要
求正确连接导线，龙头安装完毕后才可向电源盒
供电。
7. 一个交流电源盒最多可供两个感应龙头。
8. 交流电的总电源必须有合适熔断丝加以保护。
9. 请勿使产品感应窗口靠近强紫外线或电磁场。
10. 修理面盆时，用黑色电工胶布粘住感应窗口。
11.维修交流龙头时，必须断开交流电源并关闭
水源。
安装之前 BEFORE YOU BEGIN
注意事项
安装说明书
萝瑞
LOURE
质,使用水源为自来水或可供饮用水。
2．请勿将强大的冲击力施于产品，以免造成损
害，引起故障。
3．安装、清洁龙头时，切勿损伤感应窗口表面，
以免造成故障。
4．如果是安装新的洗面盆，可将水龙头和排水
组件先安装好到面盆上。
1321280-T01-A 2014
12014
K-98454T-B-CP
K-98455T-B-CP
Deck Mount Sensor Faucet
科勒（中国）投资有限公司
中国上海市静安区江场三路158号 邮编：200436
制造商：上海科勒电子科技有限公司
中国上海市宝山区丰翔路1955号 邮编:200444
Notes:
1. Flush the water supply pipes thoroughly to remove debris.
Faucet is designed for tap water or potable water.
2. Do not attack the faucet with rough strength to avoidbeing
damaged and failure.
3. Do not damage the surface of sensing window when
installing or cleaning the faucet.
4. For new installations, install the faucet and drain onto
thelavatory before installing the lavatory.
5. As for DC type faucets, please pay special attention tothe
battery poles direction. Tighten the battery cover completely
to prevent its exposure to moisture.
6. As for AC type faucets, strictly follow indicated instructions
to perform electric connection. Only provide electric supply
to power box after the installation is completed.
7. One AC/DC transformer for max.two faucets.
8. Electrical source must equipped with suitable fuse to
protect AC/DC transformer unit from damage.
9. Do not put the faucet near strong ultraviolet or
electromagnetic field.
10. Cover the sensing window with black tape when
repairing lavatories.
11.Turn off the electrical source and shut down
water supply before servicing faucet.
萝瑞台盆感应龙头（单冷型/直流电）
萝瑞台盆感应龙头（单冷型/交流电/不含电源盒）
LOURE DECK MOUNT SENSOR FAUCET(COLD,AC,W/O P)
LOURE DECK MOUNT SENSOR FAUCET (COLD,DC)

1321280-T01-A 2
推荐搭配脸盆
CAN BE MATCHED LAVATORY
使用说明 OPERATION INSTRUCTIONS
手伸到出水口下方感应范围内
（感应距离随面盆、周围的情况
而自动调节），水龙头出水。手
离开后0.5～1秒，水龙头自动止
水。
Put your hand in the sensing –range (sensing
range shall be auto adjusted per surrounding
condition), the faucet should be on. The faucet
should auto turn off after hand removal within
0.5~1 seconds.
K-2215T-M Ladena® Under Counter Lavatory
K-2210T-0 Caxton® 17" Under Counter Lavatory
K-2889T Verticyl® Rectangular Lavatory
K-2768T-1 Karess Under Counter Lavatory
K-2660T-1 Forefront™ Vessel
K-2211T Caxton® Under Counter Lavatory
K-2339T Memoirs ® Under Counter Lavatory
K-2336T Devonshire ® Under Counter Lavatory
K-2215T-M 拉蒂纳台下脸盆
K-2210T-0 卡斯登台下脸盆
K-2889T 维克长方形台下脸盆
K-2768T-1 皓玥台下盆
K-2660T-1 拂朗长方形时尚脸盆
K-2211T 卡斯登台下脸盆
K-2339T 梅玛台下脸盆
K-2336T 蒂梵诗台下脸盆
注意：
ROUGH-IN DIMENSIONS
ROUGH-IN DIMENSIONS
安装尺寸
1.推荐搭配脸盆可更好避免溅水或感应
误操作的问题。
2.不适合不锈钢脸盆。
1.1.The recommended lavatories can reduce the splashing
a
NOTE:
and misoperation issues.

3 1321280-T01-A
72
54
输出:
Input: AC220V
输入:
交流电压220V
ROUGH-IN DIMENSIONS
注意:在选用台上盆时,安装后从台面到
台盆最高处不要超过10cm,否则可能影
响美观以及手在使用时的舒适性。
K-98454T-B-CP
Whole metope
台盆顶面
Vessel rim
K-98455T-B-CP
Whole metope
Vessel rim
G1/2
G1/2
Please prepare
external thread
angle valve G1/2
Please prepare
external thread
angle valve G1/2
安装尺寸
16306T-NA
AC/DC transformer
交流电源盒
直流电压 3V
Output: DC3V
Drain
54
41.2
66.5
31.75
226
Note: To ensure beauty and comfort, the diatance
between the wall and the lavatory shall not exceed
10cm when choose self-rimming lavatory.

1321280-T01-A 4
骤步装 安 INSTALLATION
技术参数
电源：直流 2节7号碱性电池(LR03×2)
交流 电压220V,频率50/60Hz
检测时间：小于0.5秒
关阀延时：0.5～1秒
感应距离：自动调节
流量：水压为0.3MPa 时，流量不大于 2.0L/min
超时用水控制：超时用水1分钟，自动止水。
环境温度：1～55
进水温度：0.5～71
适用水压：0.05～
0.86MPa
PARAMETERS
Power: DC 2 pieces of AAA size alkaline batteries
AC 220V, 50/60Hz
Senser Duration: Less than 0.5s
Shut-off Delay: 0.5~1s
Sensing Distance: Automatic adjustment
Flow Rate: No more than 2.0L/min at 0.3MPa.
Overtime Flowing Control: Automatically stop flushing when
the faucet senses an object for more than 1 minute
continuously
Ambient Temperature: 1~55℃
Supply Water Temperature: 0.5~71℃
Supply Water Pressure: 0.05~0.86MPa
℃
℃
如需在台面开孔，建议直径为20-30mm
1.龙头与面盆的安装固定
将固定螺杆(2)安装到水龙头底部(1)
处。再把垫片(3)套在固定螺杆上。并
嵌入水龙头底部的盘槽中。然后将电
源线(7)和进水软管(8)穿过安装孔，
从面盆下方将固定橡胶垫片(4)固定金
属垫片(5)和固定螺母(6)对齐固定螺
杆(2)向上套入。调整水龙头电源线
(7)及进水软管(8)的位置。用扳手拧
紧固定螺母(6)以便把水龙头固定在面
盆上。
Fixing the faucet and lavatory
Install the mounting stud (2) to the bottom
of the faucet (1), then slip the washer (3)
over the mounting stud and put them into
the groove on the spout. Insert the power
wire (7) and supply hose (8) into the hole
from underside of the lavatory. From
underside of the lavatory, slide the rubber
washer (4), meter washer (5) and fixed
nut (6) onto the mounting stud (2).
Tighten nut (6) to make faucet installed
on the lavatory.
1
2
4
3
65
7
8
1.
When fixing the faucet directly on the
counter top, pls drill the hole of 20-30mm
in diameter.

14
15
818
17
滤网组件
Filter Assy
进水口
出水口
2.
14
15
3.
19
20
21
22
23
1.
2.
取出电池盒组件，拧开螺钉(19)，
按电池盒盖(20)上的正负极标示分
别装入2节7号电池(21)，锁紧电池
盒盖(20)的螺钉(19)后，将电池盒
组件放入阀盒的专用槽内。
注意:
电池正负极不能装反，新旧电池不
能混用。
5 1321280-T01-A
将角阀(14)与管道出水口连接，再
将软管(15)与角阀(14)连接，在软
管(15)前放一水桶，将角阀(14)完
全打开，打开供水系统，通水约一
分钟，确认管道连接触无渗漏后，
关闭供水系统。
Connect check valve (14) to outlet, then
connect the hose (15) to check valve
(14). Put a bucket in the front of hose
(15). Keep check valve (14) fully open,
turn on the water supply for about 1 min,
make sure no leakage on pipeline, and
then turn off the water supply.
2.控制阀组件的安装固定
用螺丝刀拧下阀盒盖螺钉(11)，将
阀盒盖(10)打开。根据安装尺寸图
确定控制阀组件(9)安装位置，打
孔，打入膨胀管(12)，使阀盒紧贴
墙面且控制阀组件出水口朝上，再
用膨胀螺钉(13)将控制阀组件固定
在墙壁上，注意控制阀组件要与墙
面保持平行。
Fasten control valve assembly
Unscrew valve cover screws (11) by
screwdriver, open valve cover (10).
Determine control box assembly (9)
installation location per rough-in; then
drill holes, and punch plastic expansion
tube (12) in. Place valve box against the
wall and control valve assembly water
outlet upwards, and then mount control
valve assembly on the wall by
expansion screws (13). Keep control
box assembly parallel to the wall.
Take out the battery box and loose
the screws (19), place two “AAA”
batteries into the box according to the
negative and positive pole mark on
the cover of battery box (20). Put the
box in the particular groove in the
valve box after tight the screws.
Note:
Do not mistake the pole and mix the
new and used batteries.
Then connect check valve (15) to valve
outlet to faucet assembly water outlet
hose (8).
Note:
Customer shall prepare check valve.
Do not mix water inlet with water
outlet.
No missing screen (17) and cylinder (18)
on water inlet.
再将软管(15)与阀体进水口连接，
然后连接阀体出水口与龙头组件出
水软管(8)。
注意：
1.请用户自备角阀。
2.请勿将进水口与出水混淆。
3.进水软管处的滤网组件(17)和
接头(18)不要漏装。
9
11
10
13
12

1321280-T01-A 6
最后，将电磁阀上的红绿线与对应阀
盒盖组件上的红绿线接插，将电池盒
或交流电源盒上黑橙线与主控板组
件上黑橙线接插，（交流版请将主
控板组件上的黑橙线从小U型缺口
引出与交流电源盒上的黑橙线连接）
再将探头线的红、白接插件分别与
阀盒盖上对应的红、白接插件连接，
再用阀盒盖螺钉(11)拧紧阀盒(9)和
阀盖(10)。
注意:
1. 在用螺钉固定阀盒(9)和阀盖(10)
时，确保探头线(24)需通过阀
盖上大U型缺口。
2. 接上电池后，龙头进入2分钟自动
调距阶段，此过程龙头不会出水。
二 如何安装排水组件
旋下排水器盘片(25)，在其底面沿
周围涂上一圈密封油灰。把排水
本体(26)由底下插入面盆。
How to Install the Drain
Screw off the drain flange (25) from
drain. Apply a ring of plumbers putty
around underside of the drain flange(25).
Insert the drain body(26) into the lavatory
from the underside.
Thread the drain flange (25) onto the drain
Body (26). T ighten the locknut (27) by hand
from the underside of the fixture. Remove
any excess putty.
Note: Do not try to change the position of
the drain after the locknut(27) is tightened,
or you may break the putty seal.
把尾管(28)接上存水弯(29)，尾管
需插入存水弯25mm到55mm之
间。
Connect the tailpiece(28) to the
trap(29). The tailpiece should extend
25mm to 55mm into the trap.
把排水器盘片(25)旋入排水本体
(26)。从下方用手拧紧锁紧螺母
(27)，去除多余的油灰。
注意：在锁紧螺母(27)拧紧后，
不可再调整排水本体的位置，否
则将会破坏油灰密封。
Finally, connect red-green wires on
solenoid valve with corresponding
red-green wire on valve cover
assembly; connect black-orange wire
on battery box or AC power
transformer with black-orange wire on
main control board assembly. (For AC:
please lead black-orange wire from
small “U” slot on main control board
and then connect with AC transformer
black-orange wire) then connect
red-white insert to corresponding
red-white insert on valve cover. Then
tighten valve cover screws (11) on
valve box (9) and valve cover (10).
Note:
1.Fasten valve box (9) and valve
cover (10) by screws, ensure sensing
wire (24) cross through big U slot on
valve cover.
After connect with battery, faucet
entering auto sensing distance
adjusting phase about 2 min. The
faucet will not work during this
period.
8
15
9
24
11
8
15
24 接交流电源盒
Connect AC/DC
transformer
25
Apply plumbers putty
涂油灰
26
25
27
26
28
29

7 1321280-T01-A
Connect to
electrical Source
接交流电源
Connect to
Faucet
接感应龙头
Connect to
electrical Source
接交流电源
Connect to
Faucet
接感应龙头
注意：禁止将交流AC220V接入直流DC接线端。
Note: connect AC 220V electrical source directly to DC connector is not allowed.
G1/2
Please prepare external
thread angle valve G1/2
220V交流电Connect
AC 220V
台盆顶面
Vessel rim
交流电源盒
AC/DC transformer
穿线管
Wire Tube
开关
Switch
如何安装交流电源盒
(若用户另购 交流电源盒,
具体安装详见其说明书
)
HOW TO INSTALL THE AC/DC
TRANSFORMER (ONLY USED
WITH TOUCHLESS FAUCET, AC)
一个交流电源盒供一个感应龙头
Wire connection pattern for one to one
感应龙头
Faucet
穿线管
连接线
台盆顶面
Vessel rim
G1/2
Please prepare
external thread
angle valve G1/2
交流电源盒
AC/DC transformer
感应龙头
台盆顶面
Vessel rim
感应龙头
穿线管
Wire Tube
开关
Switch
220V 交流电
Connect AC 220V
一个交流电源盒供两个感应龙头
Wire connection pattern for one to two

2. After wire layout finished, check and repair if needed.
Then connect AC connector of AC/DC transformer to
electrical source from the control box, and DC connector of
AC/DC transformer to faucet. Turn on AC electrical power,
faucet will be in the period of automatic adjustingsensing
distance (about 2 minutes). The faucet will not work during
thisperiod.
直流连接线采用导体标称截面积 mm 的电线。
请严格按照上图进行连接。
0.3
1.电源盒 (背面有不干胶)应安装在干燥，不会被水
淋湿、浸泡的位置。根据需要客户自备穿线管及
连接线。穿线管安装在墙内。建议交流电源线采用
带绝缘和护套层的电线，导体标称截面积 0.5mm ;
2. 排线完毕后，应检查并确保所有排、接线无误，
再分别连接电源盒AC接线端与排线管内交流接线
端，以及电源盒DC接线端(黑橙线接头)与龙头的
电源线接插件（从阀盒内引出的电线），最后打
开AC电源，龙头进入2分钟自动调距阶段，此
过程龙头不会出水。
1321280-T01-A 8
2
2
感应龙头
Faucet
超能动电池系统
G1/2
Please prepare
external thread
angle valve G1/2
HOW TO INSTALL THE Hybrid
Energy System (If using hybrid energy
system K-13683T as power supply, please
refer to its installation instruction)
台盆顶面
如何安装超能动电池系统 (若用户
另购 超能动电池K-13683T,具体安
装详见其说明书)
1. AC power unit (sticker on the back) should be installed at
a dry place, and avoid showering, soaking from water.
Customer prepare wire tube and wire according to
requirement. Wire tube should be put into the wall.
Suggested wire:AC connection wire should with insulated
protecting layer or sleeve and the section should ≥ 0.5mm².
The section of DC connection wire should ≥ 0.3mm².The
connection pattern must a
ccording to illustrations above.

接感应龙头
墙面
单向阀滤网组件
Check valve strainer assy.
出水口
三通
三通
thermostatic valve
外螺纹 外螺纹
单向阀滤网组件
墙面
用户自备角阀
Please prepare external
thread angle valve G1/2
用户自备角阀
Please prepare external
thread angle valve G1/2
9 1321280-T01-A
注：三通、角阀请用户自备。 angle
外螺纹
三通软管组件
用户自备角阀
Please prepare external
thread angle valve G1/2
如何转换成混水感应龙头
(若用户另购三通软管组件
1240574-SP）
HOW TO CHANGE TO MIXING SENSOR
FAUCE (If users buy the tee hose assy
1240574-SP)
如何转换成恒温阀感应龙头
(若用户另购 恒温阀16294T-3-CP,
具体安装详见其说明书 )
HOW TO CHANGE TO THERMOSTATIC
SENSOR FAUCET (If customer purchased
the thermostatic valve 16294T-3-CP,
please refer to the installation manual)
注：三通、角阀请用户自备。 angle

1321280-T01-A 10
CLEANING INSTRUCTIONS
Appliable for all finishes: clean the finish with a mild soap.
Wipe entire surface completely dry with a clean soft cloth.
Most cleaners may contain chemicals, such as ammonia,
chlorine, toilet cleaner etc. which could adversely affect the
finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler
faucets and fittings.
有腐蚀性的清洁剂或溶剂不可使用于科勒的水龙
头及其配件上。
适用于所有加工处理过的表面，以中性肥皂水清
洗镀层表面，再以干净的软布彻底擦干整个表面。
许多清洁剂，比如氨水，去污粉及洁厕灵等，会
对电镀表面造成伤害，切忌使用。
安装结果检查
检查并确保所有衔接处都已拧紧，打开排水系统
和主要供水源，检查并修理有漏水的接口。
Check and ensure that all connections are tight. Open
the drain. Turn on main water supply and check for leaks.
Repair leakage when necessary.
INSTALLATION CHECKOUT
用户须知
1. 感应指示灯的各种闪烁情况
感应指示灯是使用者了解感应龙头有效、
唯一的途径。所以明白了感应指示灯闪烁
所代表的含义，可以正确使用感应龙头，
如图示:
(1) 快速闪烁，代表感应龙头正处于通电
后的两分钟自动调节阶段。期间，安装者、
使用者不得干扰其自动调节，感应范围内
不要放置物体。
(2)
间隔约2秒钟连续闪烁：若直流感应龙
头，代表龙头电池耗尽，已停止工作，等
待使用者更换电池；若交流感应龙头，表
示为两种情况：一种为刚刚停电；另一种
为在交流供电正常的情况下，则电源盒直
流接线端接触不良。
（3）在正常工作情况下，当有物体被感
应时，龙 头出水，感应指示灯闪烁一次。
（龙头关闭，感应指示灯不闪烁。）
IMPORTANT CONSUMER INFORMATION
1. Note of the Indicator Flashing
The indicator is the only and effective way to
learn the faucet's working conditions. So the
users can use the sensor faucet correctly with
knowing the meaning of the sensor indicator's
flashing.
As shown:
(1) Quick flashing means the faucet is in the
period of adjusting sensing distance after power
on for 2 minutes. During these 2 minutes, please
do not disturb auto adjustment, no objects shall
be put in the sensing range.
(3) The indicator flashes every 2s: as for DC type
faucets, this indicates the unit out of battery and
ceases working. Please replace batteries. For AC
faucet, it indicates two possibilities: one is that
the unit is just out of battery; or poor DC terminal
contact under normal AC power supply.
(4) Under normal condition, the water will flow
and the indicator will flash once when objects are
detected. (The indicator does not flash when
faucet stops flowing.)
清理说明
指示灯
Indicator
light
2. 超时出水控制
连续在感应状态下使用约一分钟，龙头自动止水。
自动止水后，手或物体离开感应范围后，再次进
入感应范围内，龙头正常工作，否则无反应。
2. Timeout setting
When the faucet works for about continuous 1 minute, the
faucet will stop flushing automatically. After that, objects
must be removed from the sensing range. Then the water
will flow when objects enter into the sensing range again.
Otherwise, the faucet will not work.