Kohler Englefield Sorrento User manual

BEFORE YOU BEGIN
1256389-AN2-A Jan 2015
INSTALLATION
INSTRUCTIONS
TAPWARE
Englefield
SORRENTO Basin Mixer 97541A-CP
If you are building a
bathroom from scratch,
giving your bathroom a
makeover or just replacing
an old tap, Englefield can
provide a solution for you.
All information is based on the latest product information available at the time of
publication. ENGLEFIELD reserves the right to make changes in product
characteristics, packaging, or availability at any time without notice.
Please leave this installation guide for the consumer as it contains
important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove any debris.
2. An in-line water filter must be used with this product.
3. If possible, install this mixer before installing basin.
4. Ensure all local plumbing codes are observed.
5. Recommended working pressure: 100kPa to 500kPa.
6. Maximum working pressure: 800kPa.
7. If pressure exceeds 500kPa, a pressure limiting valve must be installed.
8. All installations should comply with the relevant requirements of AS/NZS 3500
and AS/NZS 6400.
ROUGH-IN
CONTACT AND WARRANTY INFORMATION
NEW ZEALAND
KOHLER NZ LTD
Free Ph: 0800 100 382
Free Fax: [phone]
www.englefield.co.nz
AUSTRALIA
KOHLER CO.
Free Ph: 1 800 ENGLEFIELD
(1 800 364 533)
www.englefield.com
For warranty information, please visit our website
Page 41256389-AN2-A Jan 2015 Englefield
INSTALLATION INSTRUCTIONS SORRENTO Basin Mixer
35
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with a
clean soft cloth. Many cleaners may contain such chemicals as ammonia, chlorine, toilet chemicals etc. which
could adversely affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Englefield tapware.

SPARE PARTS LIST
INSTALLATION
INSTALLATION CHECKOUT
1256389-AN2-A Jan 2015 Page 2 Englefield 1256389-AN2-A Jan 2015 Page 3 Englefield
SORRENTO Basin Mixer INSTALLATION INSTRUCTIONS SORRENTO Basin Mixer INSTALLATION INSTRUCTIONS
1.) Attach the inlet hoses(8) to the basin mixer body(1).
2.) Screw the threaded studs (6) into the mixer body and then place
the O-ring(3) onto the base(2).
3.) Feed the hoses through the basin hole and position the mixer in
place on the basin.
4.) From the underside of the basin, place the rubber washer(4) on
top of the mounting plate(5) and feed them over the threaded studs.
5.) Fit the nuts(7) onto the threaded studs and tighten to secure the mixer.
1.) Ensure that all connections are tight. Ensure that the handle is in
the off position.
2.) Open the basin drain as necessary. Turn on main water supply
and check for leaks. Repair as required.
3.) Remove aerator(9). Turn on the basin mixer. Run hot and cold
water through spout for about one minute to remove any debris.
Remove any debris from aerator. Shut off the basin mixer and
reinstall aerator.
1
2
3
4
5
6
7
8
9
10
11
12
13
No. Description Part No.
1 Handle 1250299-CP
2 Screw 1250284
3 Button 1250283-CP
4 Bonnet 1250279-CP
5 Nut 1250281
6 Cartridge 1250277
7 Washer 1250285
8 Aerator / Flow Regulator 1250293
9 Aerator Shell 1250290-CP
10 Base 1250307-CP
11 O-ring 1250313
12 Mounting Kit 1250272
13 Inlet Hose 1250270
1
2
3
4
5
6
7
8
9