komodo KDQNARMT12A User manual

DOUBLE HEIGHT QUEEN
AIR BED WITH 240V PUMP
KDQNARMT12A

Ensure to read all warnings and instructions in this user guide prior to first use. Failure to
comply with the warnings and instructions provided herein may result in inaccurate results
and/or damage to the air bed. Retain this user guide for future reference.
WARNING: To reduce the risk of burns, fire, electric shock or injury:
•Always unplug the air mattress when not in use.
•Adult supervision is required when the air bed is being used by or near children.
•Infants have suffocated on inflatable air beds. Never leave an infant aged less than 15
months sleeping on this inflatable air bed. Infants can suffocate on an underinflated or
deflated air bed, on bedding, by co-sleeping with another person, and by entrapment
between the air bed and bed frame, or between the air bed and a vertical surface.
•Children can be entrapped between the inflatable air bed and an adjacent vertical
surface. Provide at least a shoulder width space between the inflatable air bed and
adjacent vertical surfaces such as walls, dressers, or other objects.
•The air bed can support a total weight of up to 226kg. Do not exceed the weight limit of
this air bed.
•This air bed is made for household use.
•DO NOT use this air bed for any other purposes other than intended.
•DO NOT use the air bed outdoors or in damp areas.
•DO NOT block or insert objects into the air openings of the air bed while in operation.
•Keep air openings free of lint, hair, and other small objects.
•DO NOT use aerosols or administer oxygen when the air bed is in operation.
•DO NOT place heavy objects (for example, televisions, computer monitors) on the air
bed.
•DO NOT use the air bed around people using medical devices.
•If the power cord is damaged, stop use immediately. Contact help.Kogan.com for
assistance.
•Keep the power cord away from all heat sources.
•Keep sharp objects away from all sharp objects. This may cause damage to the air bed.
•Ensure the air bed is fully inflated when in use.
•If inflating the air bed manually, use a low-pressure inflator. Do not over inflate.
•Keep the felt side of the air bed facing up.
•DO NOT dissemble the air pump.
•DO NOT operate the pump in the presence of explosive and/or flammable fumes.
•DO NOT place any part of the pump or cord in or under water or any other liquid.
SAFETY & WARNINGS

•DO NOT place this air bed on heated surfaces. Fires may occur if the air bed touches or
is covered by flammable materials including curtains, draperies, cardboard, and
plastics while in operation.
•DO NOT operate the pump in enclosed spaces that are not well-ventilated.
•DO NOT use chemicals to clean the air bed.
Attention: PVC material
The air bed is made from PVC material. PVC will naturally stretch and expand during use.
After being inflated and/or having been slept on for several days, the air bed may lose some
of its initial firmness due to the PVC expanding. This is normal and is not the result of air
leaking from the air bed. Add air to the air bed to regain your desired firmness level through
the built-in air pump.
WARNING: This air bed is operated with an electrical air pump that is
thermally protected. The pump does not contain parts that can be
repaired or serviced. It may cause explosions or electric shock if the
pump is disassembled. If you have any issues with the electrical pump
upon arrival, please contact help.Kogan.com for assistance.

1 Air bed 5Control dial
2 Power cord 6 Valve cap
3 Power cord storage compartment 7 Valve
4 Air vent 8 Liner cap
OVERVIEW
INFLATE
DEFLATE
OFF

Se
Remove the air bed from its packaging and unfold it so that the textured side is facing up.
After removing the air bed from its packaging, leave it out in an open space. There may be a
slight smell, which is normal and non-toxic. It may take up to a week for the air bed
completely air out.
1. Open the power cord storage compartment and connect the power cord to a power
outlet. Turn on the power outlet.
OPERATION
BEFORE FIRST USE
INFLATE
DEFLATE
OFF

2. Turn the control dial clockwise until the marker points towards “INFLATE” to pump
air into the air bed.
3. Turn the control dial anti-clockwise to "OFF" when the air bed has reached the
desired firmness level.
INFLATE
DEFLATE
OFF
Notes:
•After 5 minutes of continuous use, the air pump will start to generate heat. Allow
the air pump to cool down for 30 minutes before resuming use. It is not
recommended to run the air pump for longer than 5 minutes.
•Ensure there is at least a 60cm clearance from any wall or object while the
pump is in operation.
OFF

4. Lie on the air bed to test its firmness.
5. If you wish to make further adjustments, the control dial can be turned clockwise to
further inflate or turned anti-clockwise until the marker points towards “DEFLATE” to
let air out of the air bed. Turn the control dial back to “OFF” after achieving the
desired firmness level.
6. Unplug the power cord and store it back into the power cord storage compartment.
The air bed is now ready for use.
Deflation and storage
1. Plug in the power cord to a power outlet and switch the power outlet on. Turn the
control dial anti-clockwise to deflate the air bed.
2. After the air bed is completely deflated, unplug the power cord and place it back
into the storage compartment.
3. Lay the air bed with the textured side facing up and fold the air bed into thirds. Roll
up the air bed to release any remaining air and store away.
Notes:
•After inflating the air bed for the first time, it is recommended to wait for 8-12 hours
so that the seams can buffer.
•It is normal for the mattress to lose a small amount of air after being fully inflated.
•During initial use, the air bed may soften and require additional inflation to
maintain desired firmness. This is normal.
•If the air bed is intended to be used for an extended period, inflate the air bed for
10-15 seconds every day to maintain its firmness.
OFF
DEFLATE
INFLATE

Apart from using the power cord and control dial, the air bed may be manually
inflated/deflated.
Manual inflation
1. Open the valve cap and connect an air pump or hose (not included) into the valve.
2. Turn on the air pump or hose and inflate to the desired firmness. Close the valve
with the valve cap. The air bed is ready for use.
Manual deflation
1. Fully open the valve, exposing the liner cap to release all the air from the air bed.

•To clean the air bed, use a mild soap solution and water.
•Do not use chemicals to clean the air bed.
•If the air bed needs to be repaired, use common PVC repair glue and patches.
Material PVC
Size Queen
Dimensions 203 x 152 x 46cm
SPECIFICATIONS
CLEANING & CARE

NOTES

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com