Koncept UCX PRO Manual

Seng up your UCX pro Wifi Module
Plug in the wifi module to any open end of a UCX pro, make sure the UCX pro unit is powered.
Make sure all UCX pro lights are set in GROUP mode; To do so, turn off the lights, touch and hold the MODE buon to
switch to GROUP mode. Make sure the blue LED signal light on the UCX pro is indicang it is in GROUP mode.
Installing the Koncept app
Proceed to the App Store on an iPhone or the Play Store on an Android phone, search for the “Koncept wifi control”
app and download to install the Koncept app.
LED UNDERCABINET LIGHT
Wi-Fi module setup instructions

There are different methods to connect the module to your network, for iphones and Android phones, please follow the below
instrucons accordingly.
for iPhone
Connecng to your Wifi network
You should noce a slowly blinking blue LED on the wifi module, which means it is in AP mode ready for setup.
Connect your phone to the wifi network _koncept_
A pop up window like below should show up.
Go ahead enter your network ID and password.
It will now detect the device and ask you to enter your wifi Network ID and password. Go ahead enter your network ID and password.
The blue LED will become solid aer the Wifi module is connected to your network. Now connect your phone to back to your wifi.
(Oponal step) Just in case the pop up window did not show up, open the Koncept app.
Click on the menu icon at the top le corner, select “+ ADD A DEVICE” on the menu.
LED UNDERCABINET LIGHT
Wi-Fi module setup instructions

for Android phone
You should noce a slowly blinking blue LED on the wifi module, which means it is in AP mode ready for setup.
Connect your phone to the wifi network _koncept_
A pop up message like below would show up, tap on that, it would then bring you to the other page.
Please enter your network ID and password.
If the methods above do not work for you, you may try connecng through WPS.
You should noce a slowly blinking blue LED on the wifi module, which means it is in AP mode ready for setup.
While the Blue LED is blinking slowly, press and hold the buon on the back of the Wifi module for 10 seconds.
Aer the buon is released, the wifi module will enter WPS mode and the blue led will now blink rapidly.
Press the WPS buon on the router, and wait for the wifi module to connect to the router.
Once the wifi module is connected, the blue LED will become solid.
Connect through WPS
The blue LED will become solid aer it is connected.
LED UNDERCABINET LIGHT
Wi-Fi module setup instructions

Configure your UCX pro lights
Once you have completed seng up the UCX pro WIFI module, you are ready to configure your UCX pro lights using the Koncept app.
Now open the Koncept app.
Click on the menu icon at the top le corner, select “DEVICES” on the menu. Click on the check box to select the device.
Click on the menu icon at the top le corner, select “HOME” on the menu, this will bring you back to the home page.
(Oponal steps) Click on the name of the device to edit sengs, an “edit device” page will show up.
Rename device : You may rename the device by clicking onto the name of device, rename it to something easy to recognize.
Lock device - On the network this device will be displayed as locked, and can only be unlocked by having physical access.\
Firmware upgrade : When there is a new release of firmware, an upgrade buon will show and you may click to upgrade.
Power consumpon : You can see an esmaon of the power consumed since the installaon. Hit reset would restart the esmaon.
You should noce count of the “device(s) selected” at the lower right corner has changed to 1.
LED UNDERCABINET LIGHT
Wi-Fi module setup instructions

To adjust brightness, click on the upper le icon to open the brightness control, you may start dialing around
the circle to adjust brightness. Once you are done, click back < icon at the upper le to return to home page.
To light color, click on the upper right icon to open the color control, you may start dialing around
the circle to adjust light color. Once you are done, click back < icon at the upper le to return to home page.
The power icon on the lower right can be used as a toggle ON/OFF control.
Basic Control
5
LED UNDERCABINET LIGHT
Wi-Fi module setup instructions

LED UNDERCABINET LIGHT
Wi-Fi module setup instructions
Advanced Control (Scheduling)
6
You may set specific me to turn the lamp on/off/dim, according to your schedule throughout the week. Mulple users sharing the
same UCX pro could each set their schedule to have the light on at the ming they use the desk.
Circadian light : UCX pro has the capability to change light color. Besides just being a personal preference on the color, you can
customize a light color schedule to help shi your circadian rhythm to its normal paern, automacally everyday.
Circadian rhythm is like an internal “Clock” in the brain that regulates the ming of sleepiness and wakefulness throughout the day.
It is suggested that having warm light at aernoon/night with cool light in the morning helps ease the body into and out of sleep in
order to create your own perfect sleep cycle.
Click on the menu icon at the top le corner, select “SCHEDULES” on the menu, this will bring you to the schedules page.
Click on the “+ schedule” to create new schedule. A default 12:00pm schedule will be created, click on it to go to the “sengs” page.
Click on the lower right icon to go to the “devices” page and select the device that you want to edit, click the back < icon to go back.
Click on the lower le ming icon to go to the “set me” page. Select the preferred am/pm, me and the days of the week, then hit the
back < buon. Choose the brightness and light colors. Once Brightness, Light color and ming are all set, hit the back < buon to go back
to the “schedules” page. You may create as many schedules as you like by repeang the process.