KOVAX PROMA-X AIR 150 V2 User manual
INSTRUCTION MANUAL
Art.No.: 910-0620
AIR 150 V2
PNEUMATIC RANDOM ORBITAL SANDER
PAGE 2 | PROMA-X AIR 150 V2
PROMA-X AIR 150 V2
PNEUMATIC RANDOM ORBITAL SANDER
page
Proper Use of the Tool 3
Work Stations 5
Putting the Tool into Service 5
Operating Instructions 6
Please Read and Comply With: 6
Declaration of Conformity 7
PAGE 3 | PROMA-X AIR 150 V2
PROPEER USE OF THE TOOL
Proper Use of the Tool
This sander is designed for sanding all typens of materials i.e. metals,wood, stone, plastics,etc. using abrasive designed
use back-up pads that have a working speed less than 12.000 RPM free speed.
Work Stations
The tool is intended to be operated as a hand held tool.It is always recommended that the tool be used when standing on
and footing and be aware that the sander can develop a torque reaction. See the section Operating Instructions.
Putting the Tool into Service
Use a clean lubricated air supply that will give a measured air pressure at the tool of 90 psig(6.2bar) when the tool is
airline. It is recommended that the tool be connected to the air supply as shown in Figure 1.
Do not connect the tool to the airline system without incorporaing an easy to reach and operate air shut off valve. The air
obtained from your supplier. If such equipment is not used then the tool should be manually lubricated by shutting off
the air supply to the tool. Disconnecting the airline and putting 2 to 3 drops of suitable pneumatic motor lubricating oil,
preferably incorporating a rust inhibitor into the hose end (inlet)of the machine. Reconnect tool to air supply and run tool
slowly for a few seconds to allow air to circulate the oil. If tool is used frequently lubricate on daily basis and if tool starts to
slow or lose power. It is recommended that the air pressure at the tool be 90 PSI (6.2 Bar) whille the tool is running so the
Bar). If run at lower pressure the performance of the tool is reduced.
PAGE 4 | PROMA-X AIR 150 V2
OPERATING INSTRUCTIONS
Operating Instructions
1. Read all instrucions before using this tool,alll operators must be fully trained in its use and aware of the safety rules.
All service and repair must be carried out by trained personnel.
2. Make sure the tool is disconnected from the air supply. Select a suitable abrasice and secure it to the back-up pad.Be
careful and center the abrasive on the back-up pad.
3. Always wear required safety equipment when using this tool.
4. When sanding always place the tool on the work then start the tool.Always remove the tool from the work before
5.
6.
7. Use only correct spare parts.
9.
being started when carrying the tool with the air supply connected.
10. Dust can be highly combustible.Vacuum dust collection bag should be cleanded or replaced daily. Cleaning or
replacing af bag also assures optimum performance.
11.
12. The tool is not electrically insulated. Do not use where there is a possibility of coming into contact with live electricity,
gas pipes, water pipes, etc.Check the area of operation before operation.
13. Take care to avoid entanglement with the moving parts of the tool with clothing, ties, hair, cleaning rags, etc. If entang,
it will cause the body to be pulled towards the work and moving parts of the machine and can be very dangerous.
14. Keep hands clear of the spinning pad during use.
15. If the tool appears to malfunction,remove from use immediately and arrange for service and repair.
16.
abrasive or pad.
PAGE 5 | PROMA-X AIR 150 V2
SPECIFICATIONS
SPECIFICATIONS
SIZE 150 MM
WEIGHT 970 G
AIR CONSUMPTION
AIR PRESSURE 6.2 BAR
MAXIMUM ROTATIONS 12.000 RPM
Features include:
•
• Ergonomic Cushion-Grip for Comfort and Stablility
•
•
• Suggested Applications: Sanding and Finishing a Variety of Materials including Wood, Metal, Plastics, Fiberglass
Composites,Solid Surfaces and other Sandable Surfaces
WARNING
OIL DAILY
Operators Instructions
Read and Comply. Assembly Drawing of Machines, Part List, Proper Use of Tool,
Works Stations, Putting the Tool into Service, Operating Instructions.
Important
Read these instructions carefully before installing, operating, servicing or
repairing this tool. Keep these instructions in a safe accessible location.
Always wear safety goggles to
protect your eyes.
Oil daily for superior performance
PAGE 6 | PROMA-X AIR 150 V2
PLEASE READ AND COMPLY WITH:
Please Read and Comply With:
reguiations.
1. TOOL INTENT - Tool shall be used only for purposes intended in its design.
2.
3. UNUSUALSOUND or VIBRATION - If tool vibrates or produces an unusual sound, repair immediately for
correction.
4. OPERATOR PROTECTIVE EQUIPMENT - Wear goggles or face shield whenever tool is in operation.
Other protective clothing shall be worn, if necessary. See regulations.
5. SAFETY MAINTENANCE PROGRAM - Employ a Safety program to provide inspecion and maintenance of all
phases of tool operation and air supply equipment in accordance with "Safety Code for Portable Air Tools".
PAGE 7 | PROMA-X AIR 150 V2
DECLARATION OF CONFORMITY
Kovax Europe B.V. | 7602 KC Almelo | The Netherlands
We declare under our sole responsibility that the product ProMa-XAir 150 V2,to which this declaration relates is in
accordance with the test standards: EN ISO 12100:2010
Manufacturer / Supplier:
Almelo, 12.01.2022
Place and date of issue Company Willem Mulderij , Managing Director
7602 KC Almelo
The Netherlands
This manual suits for next models
1
Table of contents
Other KOVAX Sander manuals
