KRAFTOOL Zubr Master PU-60-1400 M4 User manual

Instruction Manual
Multipurpose Vacuum Cleaner
PU-60-1400 M4
KRAFTOOL HONG KONG LIMITED
www.kraftool.hk
170671
Version: 111018
MASTER

www.kraftool.hk www.kraftool.hk
Dear customer!
When buying the product:
`please demand checking its serviceability by a test run, as well as completeness according to the
delivery contents.
`please make sure that the warranty card is duly issued and contains the serial number of the product,
the date of sale, the stamp of the store and the signature of the seller.
Before running the product for the first time, please carefully read this manual and strictly
follow the requirements contained therein. This is the only way for you to learn how to properly handle
the product and avoid mistakes and dangerous situations. Please keep this manual for the lifetime of your
tool.
Remember! The product is a source of increased fire danger.
`Do not use the product without a filter.
`Do not allow the suction of aggressive,
combustive-lubricating,viscous and suspended
liquids (emulsions,suspensions,mastics,
adhesives,whitewashing,water-based paints,
etc.), as well as cooling lubricants,used in the
operation of handheld,portable and stationary
machines and machine tools!
`Do not allow the suction of toxic materials in
order to avoid harm to health by fumes and dust.
`It is forbidden to connect power tools with a
power exceeding the allowable for this product.
`Do not use and store the paper filter in rooms
with a relative humidity of more than 70% in
order to avoid loss of paper and glue properties.
`Do not use the paper bag when vacuuming
metal chips, concrete dust, stones and mixtures
with large and sharp solid inclusions.
Purpose and scope
Please study the present Manual closely, including
the Appendix Basic Safety Instructions. This is the
only way you can learn how to properly handle the
tool and avoid mistakes and dangerous situations.
The product is intended for short work at loads
of medium intensity in areas with a temperate
climate with a characteristic temperature from +1
to +35°C, relative air humidity not more than
80% at a temperature of + 25°C and with no
direct exposure to precipitation and absence
of excessive dustiness of the air.
The product meets the following requirements:
`ТР ТС 004 / 2011 «On the safety of low-voltage
equipment»;
`ТР ТС 020/2011 «On the
electromagnetic compatibility of technical
equipment».
This manual contains the most complete
information and requirements necessary and
sufficient for reliable, effective and safe operation of
the product. Because of further works on
improvement of the product, the manufacturer
reserves the right to make minor changes in its
design not shown in this manual, as they do not
affect the effective and safe operation of the
Product.
The use of the product in industrial volumes,
in conditions of high intensity of work and
super-heavy loads reduces the service life of
the product.
14
2
3
4
5
6
8
7
11
12
13
910
ATTENTION
2 | Operation Manual Multipurpose Vacuum Cleaner| 3
ATTENTION
1

www.kraftool.hk www.kraftool.hk
All work on assembly,replacement,and
adjustment of the product or its parts must be
performed only when the product is disconnected
from the mains.
If the product is brought into a heated room from
the street in winter or from a cold room, do not
unpack it and do not turn it on for 8 hours. The
product should warm up to the room
temperature.Otherwise, it may broke when turned
on.
Wheels installation:
`Turn over the product.
`Install two swiwel wheels 2into the special
sockets in the bottom of the base 1.
`Install wheels 14 on axis 16.
`Install and secure the axis 16 with screws 15.
`Set the product on a flat, stable surface.
14
2
15
16
Filter installation:
Do not use the product without filter!
`Open the latches 12 on both sides of the
product, use the handle 10 to remove the
motor section 7.
`Install the appropriate filter, depending on the
type of cleaning.
`For dry (without water suction) cleaning
install filter HERA 19 or polyurethane filter 20
on the filter housing 18.
`Also when you doing dry cleaning install bag 22
on socket 21 from inner side of the tank 4.
Do not do a dry cleaning without the bag!
`Always make sure that the bag 22 is not full,
change it to a new one if necessary (bag
capacity depends on the intake dust).
`When you do wet cleaning (water suction),
install a polyurethane filter 20. Do not install the
bag 22 in this case.
4| Multipurpose Vacuum Cleaner | 5
  Operation instructions
Configuration
1 Base
2 Swivel wheels
3 Nozzle
4 Tank (body
5 Suction hose
6 Composite pipe
7 Elecric motor section
8 Switch
9 Socket for power tool connecting
10 Electric motor section handle
11 Vacuum cleaner handle
12 Latches
13 Drain hose
14 Wheels
15 Screw
16 Axis
17 Safety valve
18 Filter housing
19 НЕРА filter
20 Wet cleaning filter
21 Socket
22 Garbage bag
Assembling
Ensure that the product and the kit do not have any damage that may have occurred during
the shipment.
Specifications Table 1
ATTENTION
ATTENTION
ATTENTION
ATTENTION
ATTENTION
Operation Manual
PU-60-1400 M4
220
50
1400
60
17
40
Suction /blowing
HEPA
F9
L
2000
78
82
-
II
11
14
5
Parameter
Rated supply voltage, V
Frequency Hz
Rated power consumption, W
Effective dust volume
Air vacuum (not less than) kPa
Air consumption, liter /s *
Operation mode
Filter
Filter class
Dust class
Maximum power of the connected instrument, W
Sound power level (k =3), dB
Sound pressure level (k =3), dB
Vibration level (k = 1.5), m / s2
Safety class according to GOST 12.2.007.0-75
Product weight, kg
Brutto, kg
Service life, years
*with a clean filter
Vacuum cleaner
Disposable paper bag
Cloth bag
HEPA filter
Filter for wet cleaning (polyurethane)
Plastic corrugated hose (3 m)
Composite pipe
Universal nozzle
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
4 pc
1 pc
1 pc
1 pc
1 copy
Power tool connecting adapter
Wheels
Axle for wheels
Drain hose
Mounting kit
Instruction manual
Crevice nozzle
Contents of delivery

`After installing appropriate filter correctly install
electric motor section 7 by the handle 10 on
tank 4 and close latches 12.
`Ensure that safety valve 17 moves freely in the
filter housing 18 and when installing the motor
section 7 on tank 4 valve 17 was located on the
lower part of the filter housing 18.
Corrugated hose installation:
`Rotate the trumpet of the hose 5 into the slot 21
so that the lock (protrusion) on the hose 5
trumpet fits into the locking groove of the socket
21.
` Make sure that the hose 5 is not twisted, and
nothing interferes with the movement of air in it.
Do not squeeze the hose 5.
Preparation for work
Three position switch:
`Neutral (middle) position - the product is
switched off;
`Position «I» – the product is on, regardless of
the fact of connecting the power tool to the outlet
9;
`Position «II» - the product turns on after a few
seconds only after starting power tool
connected to scoket 9, and the product turns off
after a few seconds only after stopping.
Nozzle installation:
`Install the nozzle 3 on the hose 5. The type of
nozzle is selected depending on the type
of cleaning.
`Use the crevise nozzle to remove dust from
hard-to-reach places, drawers, cabinets, slots,
heating radiators.
`Use the universal (bristle) nozzle for dry and
wet cleaning. This nozzle is designed for
wet cleaning. This bristled nozzle is designed
for wet cleaning (with water suction) of
smooth surfaces.
`If the length of the hose is not enough, connect
the hose 5 trumpet with the nozzle 3 through
the composite pipe 6.
Power tool connection:
On the electric motor section 7 is installed a socket
9 for connecting a power tool, which provides
automatic switching on and off of the product
at the same time as switching on or off the electric
tool.
Carefully read the instructions, rules and manuals
of the connected power tool.
Before connecting the cord of the power tool to the
socket 9, make sure that:
`the power tool is in working condition;
`the power tool does not exceed the maximum
allowable power (see table 1);
`the power tool cord fits into the socket 9;
`the power tool is swiched off (look at the power
tool swiches to check it).
Many power tools have a dust collector pipe for
connecting to a vacuum cleaner. The product
comes with an adapter for connecting the hose
nozzle 5 to the dust nozzle of the power tool.
The product moving
For the convenience of movement, the product
has swivel wheels 2 and non-swivel wheels 14.
The product can only be moved and rolled by the
handle 11. The product must be moved when the
electric motor is off.
Watch out for the power cord when moving the
product. Moving the product should not exceed
the length of the power cord. If you are going to
move the product far away, unplug it from the
electrical outlet first.
Make sure that the product is assembled
correctly before move any further.
Set switch 8 to the neutral position.
`Connect the product power plug to an electrical
outlet.
`Set switch 8 to the position «I»:
The product will turn on. Let it idle for at least two
minutes, and if you find anything abnormal in the
work of the product, shut it off immediatly, set
the switch to the neutral position and unplug
the product cord from the electrical outlet.
If you were unable to find out the cause of the
malfunction by your own, contact a certified service
center.
When you turn on the product in the first time,
let it idle at least for 5 minutes. At this time the
appearence of foreigh smell is possible, this is
due to the first running in of the electric motor.
Soon the smell must disappear.
Dry cleaning
`For dry cleaning you need to set an appropriate
filter (19 or 20), garbage bug 22 and a nozzle on
the filter housing 18.
`Turn on the product and start cleaning.
Regularly check the condition of the hose 5
and nozzles. All nozzles and hose 5 must
freely pass the intake air. Keep the hose and
nozzles clean. Do not vacuum any liquids
during dry cleaning.
`Periodically monitor the filling of the bag 22.
Cleaning a floor from water and wet cleaning
`For wet cleaning it is necessary to install only
the filter 20 and the corresponding nozzle. Do
not install the garbage bag 22.
`Start cleaning. Regularly check the condition of
the hose 5 and the nozzle.
Operating procedure
Nozzles and hose 5 must freely pass intake
water and air. Keep them clean and do not
allow any pollution on nozzles and hose.
`Water absorbed and accumulates in the tank 4.
When the water level in the tank 4 will exceed
the maximum limit, the safety valve 17 will close
the suctioning inlet and the suction will stop.
The product sound of work will change after
that, and in this case, you need to immediately
turn off the product. Always drain the water from
tank 4 after cleaning, to do this, remove the
plug from drain hose 13.
`Before start cleaning, always check (with the
power cord unplugged from the outlet) safety
valve 17 for free movement in the filter housing
18.
Interworking with power tool
` Connect power tool to the product.
` Power tool must be in the off state (pay
attention to the power tool switches).
`Turn the switch 8 to position “II”. Start working
with a power tool. A few seconds after the
power tool is turned on, the product turns on
and starts to collect debris and dust resulting
from the operation of an electric tool.
`After turning off the power tool, the product will
also stop working after a few seconds.
`If the power tool has a power, less than the
power of synchronous operation with the
product (see table 1), it is necessary to turn the
switch 8 to position "I". In this mode, the product
will turn on and will work continuously until it is
turned off (switch 8 to the neutral position) -
regardless of whether the power tool is on or
not. Only in this mode, it is possible for the
product to operate with low-powered tools, or
with the tools connected to a separate source of
electrical current (not to the outlet 9).
4212218 20 17
ATTENTION
ATTENTION
ATTENTION
ATTENTION
www.kraftool.hk www.kraftool.hk
6| Operation Manual Multipurpose Vacuum Cleaner| 7

www.kraftool.hk www.kraftool.hk
8|Multipurpose Vacuum Cleaner| 9
Cleaning the tool
Remember! Clogged or damaged filters
significantly reduce the performance of the
vacuum cleaner, the quality of cleaning,and
can cause the product to break.
Before cleaning the product and its filters
from dust and debris, you must use
personal protective equipment for the
respiratory tract and eyes. Clean the product
from dust and dirt in a specially
designated place.
`At the end of the work, turn off the product
(turn switch 8 to the neutral position) and
remove the power cord of the product from
the electrical outlet.
`Open the latches 12 on both sides of the
product and use the handle 10 to remove
the motor section 7.
After dry cleaning:
`Remove bag 22. Replace the bag with new one
or clean it in case of filling;
`Do not wait until the bag 22 is filled, change it as
it is filled. Excessive filling of the bag leads to
a decrease in the performance of the
product,therefore, monitor the filling of the bag
22, taking into account the properties of the
intake garbage.
`Carefully remove the HERA filter 19 or the
polyurethane filter 20 from the filter housing 18
and clean them from dust and dirt;
`If necessary, carefully blow the removed HEPA
19 filter with compressed air from the inside to
the outside;
`Polyurethane filter 20 can be washed with clean
water and soap, then be sure to rinse with clean
it with water, squeeze and dry it;
`If you find that one of the filters is damaged or
unusable, it should be replaced with a new one;
`Clean the inside of tank 4 of dust and dirt. If
necessary, wash the tank 4 with clean water
using a liquid (non-abrasive) detergent. After
that, rinse it well again with clean water and dry
until completely dry.
After wet cleaning or water absorption:
`Drain all water from the tank 4;
` Remove and wash the polyurethane filter 20 with
clean water, and dry it;
`If necessary, clean tank 4 with clean water using
a liquid (non-abrasive) detergent. After that,
rinse tank well again with clean water and dry
until completely dry.
`After any type of cleaning, make sure that the
safety valve 17 and the inside of the electric
motor section 7 are clean. If necessary, wipe
them with a damp soft cloth and dry. When
cleaning these parts and surfaces use water
and soap.
Solvents can damage the product surface.
` After cleaning, install the filters in place.
Correctly install the motor section 7 by handle
10 on the tank 4 and close latches 12.
Take care that the safety valve 17 must move
freely in the filter housing 18 and located
in its bottom when installing the motor
section 7 on the tank 4.
`After work, be sure to clean the inner and outer
surfaces of the nozzles, hoses, extension
cords,adapters, trumped, etc., after
disconnecting them from the product. If
necessary,wipe their outer surfaces with a
damp soft cloth and dry. Rinse the internal
surfaces of these parts (if necessary) with a
stream of clean water and dry. When cleaning
these parts, use water and soap. Remember,
solvents can damage the surface.
Periodical maintenance
For your own safety, you must turn off the
product and unplug the power cord from the
electrical outlet before performing any
adjustment and maintenance of the product.
The product does not require constant
maintenance. but attentive care is needed. This will
be the key to the normal operation of the vacuum
cleaner and will prevent possible injury.
`Do not allow dust, debris and foreign objects to
accumulate on the outer surface of the productr
and its parts.
`Replace worn filters and parts when necessary.
`Regularly clean the wheels from dust and dirt,
as well as from hair, cloth, etc.
`The product should always be checked
before work. All faults must be removed before
work.
If the power cord is worn off, cut or has any
other damage, replace it immediately.
Recommended
practices
Make sure that your mains voltage matches the
rated voltage of the product. Turn on the product
only when you are ready to work.
Before using the product for the first time, turn it on
without load and let it work for 5 minutes. If at this
time you hear extraneous noise, feel increased
vibration or the smell of burning, turn off the
product, disconnect the power cable from the
mains and determine the cause of this
phenomenon. Do not turn on the product before
the cause of the malfunction has been found and
corrected.
The three-position switch of the product should be
in the middle neutral position, in which the vacuum
cleaner is turned off.
The product is designed to collect only water and
household cleaning solutions. Do not use it to
collect salts, acids, aggressive, explosive and
flammable liquids.
Do not allow the product to operate with a fully
filled dust bag or a blocked safety valve. Significant
restriction or the complete absence of air passage
through the electric motor leads to its overheating
and breakage. To avoid damage to the product,
clean it regularly to remove accumulated dust and
dirt.
The socket of the product is designed to connect
an power tool with a capacity of no more than
2000 W of safety class I according to GOST
12.2.007.0-75.
To avoid overheating, take breaks in the work of
the product, sufficient to cool it.
During operation, the pumped air exits through the
hole in the upper part of the product. Do not cover
it, allow air to escape from the product.
Regularly check the status of the mains cable.
Prevent damage to insulation, pollution by
aggressive and conductive substances, excessive
pulling and bending loads.A damaged cable must
be replaced immediately at the service center.
Turn off the product from the network immediately
after work. Do not turn off by simply unplugging the
power cord (by removing the plug from the outlet).
Periodically clean the dirt and dust from the
housing and cable, ventilation openings.
All maintenance work must be carried out when the
cable is disconnected from the network.
The product does not require other special service.
All repair work should be carried out only by
specialists of the service centers.
Keep the product in good condition.
In the event of suspicious smells, smoke,
fire,sparks, turn off the machine, disconnect it
from the power supply and contact a
specialized service center.
If the product seems to be defective, immediately
stop its operation.
Due to the technical complexity of the product, the
criteria for limiting states cannot be determined by
the users on their own.
In case of obvious or suspected malfunction, refer
to the section “Possible faults and elimination
methods”. If there is no malfunction in the list or
you could not solve it, contact a specialized
service center. The service center issues a
conclusion on the limiting condition of the product
or its parts in the form of the relevant Act.
ATTENTION
Operation Manual
ATTENTION
ATTENTION
ATTENTION

www.kraftool.hk www.zubr.ru
10|   Multipurpose Vacuum Cleaner | 11
указания к ним.
` Не размещайте шланг и шнур питания в про-
ходах.
Warranty
We constantly care about improving the quality of
service to our customers, therefore, if you have
any complaints about the quality and the period of
warranty repair, please, let us know in the 3Y6P
support service by e-mail to [email protected].
Safety instruction
Before turning on the product for the first time, pay
attention to the proper assembly and the
reliability of its installation.
`Do not block the inlet.
`Use the product on a stable, flat surface.
Eliminate spontaneous movement of the product.
`Do not use the product without a filter.
`Do not unplug the product by pulling the power
cord. When unplugging the product, hold it by
product's plug, but not for the power cord.
`Before disconnecting from the power supply,
move the three-position switch to the middle
position.
`Do not pull or move the product by the power
cord or hose.
`Keep the power cord away from hot surfaces
and sharp edges, protect it from any
damage.
` Do not allow large foreign objects to enter the
input and output channels.
`The operation of the product with closed
channels is forbidden.
`Do not install and operate the product in
rooms with a relative humidity of more than
80%.
` Take care of good workplace lighting and
freedom of movement around the product.
`Do not work in hazardous conditions.
`Children and unauthorized persons should be at
a safe distance from the workplace. Lock
the work area. The product is not intended to
be used by people (including children) who
have physical, nervous or mental abnormalities
or lack of experience and knowledge, unless
such persons are supervised or instructed to use
the vacuum cleaner by the person responsible
for their safety. It is necessary to supervise
children in order to prevent them from playing
with the product.
`Use the product only for its intended
purpose.
`Before starting any maintenance, parts
replacement or cleaning vacuum cleaner, as well
as when connecting a power tool to the product
unplug the power cord from the electrical outlet.
replacement or cleaning vacuum cleaner, as well
as when connecting a power tool to the product
cleaner switch.
`Do not touch the power plug with wet hands.
`Hair, loose clothing, fingers, etc. should not be
located near the air intake.
`Low power or damaged extension cords can
cause a fire or electrical shock.
`Avoid getting fluff, hair, or anything else in the
air intake that could interfere with air flow.
`Connect the product to a grounded outlet only.
` Inspect the product before each use. If any
parts are missing, deformed, or
deteriorated, or the electrical components do not
work properly, turn off the product and unplug
it. Replace damaged, failed parts, and install
missing parts. Only then the operation of the
product can be resumed.
`When cleaning the product, use respiratory
protective equipment (respirator) and eyes
(goggles).
`If you find something abnormal in the operation
of the product, immediately stop its
operation.
` Follow all safety requirements when working
with a power tool that plugs into the
product. Carefully read all the documentation on
the power tool used in conjunction with a
product.
`It is forbidden to connect a power tool with a
power exceeding the allowable amount for the
product (see Table 1).
`It is forbidden to alter the outlet located on the
product if the plug of the connected power
tool is not inserting into it.
`Unwind the power cord completely before using
the product.
`Drain the water from the product is carried
out only after the product is completely
disconnected from the mains.
`Use only original and recommended accessories,
following all instructions to them.
`Do not place the hose and power cord in the
aisles.
`It is forbidden to operate the disassembled
product.
suspensions, mastics, adhesives, whitewash,
water-based paints, etc.), as well as lubricating
coolants used during operation. manual,
tools.
Operation Manual
At the same time, the three-position switch of the
vacuum cleaner should be in neutral position.
`It is forbidden to stand on the product,put on it
power tools and other items.
`Do not leave the working product unattended.
Before leaving the workplace, turn off the
product, wait until it stops completely, and
unplug the power cord.
`Do not attempt to clean, remove the dust bag or
maintain the product when the power cord is
connected to an electrical source. Turn off the
product and unplug the power cord first.
`Before starting work, visually check the product,
cable and connecting elements (corrugated
hoses, tubes, nozzles) for visible mechanical
damage.
`It is unacceptable to use the product with
damaged cord or other nodes. If the product
is not working properly, there are no parts,
if it is dropped, damaged, contact the
service center.
`Do not touch moving parts (under covers,
covers) of the product.
`When working in adverse conditions (dusty,
increased noise level), use personal protective
equipment.
`Do not use the product near flammable or
combustible liquids, gases, gasoline, lighters,
solvents, oil-based paints, natural gas,
hydrogen, or explosive dust from coal,
magnesium, or gunpowder. Sparks inside
electrical components can ignite fumes or dust.
Do not store the product near
hazardous substances.
`Avoid sucking up burning or smoking cigarettes,
matches or hot ashes.
`In order to avoid harm to health by fumes or
dust, do not allow suction of toxic materials.
`Do not use the product to collect aggressive,
combustive-lubricating (POL), viscous and
suspended liquids (emulsions, suspensions,
mastics, adhesives, whitewash, water-based
paints, etc.), as well as lubricating coolants used
during operation manual, portable and stationary
machines and machine tools.
`Prevent moisture from entering the electrical
connections, motor, electrical outlet and vacuum
The warranty period is 6 months from the date
of sale.
1) Warranty does not cover:
a) Parts subject to working and other types of
normal wear and tear, as well as equipment
malfunction caused by these types of wear, and
the product, which has the full development of
the resource, strong external or internal
pollution.
b) Tool malfunctions caused by non-compliance
with the Operating Instructions or occurring due
to misuse of the tool, during use in environmental
conditions beyond the specified operating
instructions, inadequate working conditions, due
to overloading or insufficient, inadequate
maintenance or care. The unconditional signs of
product overload include, among others, the
appearance of colors of tinge, simultaneous
failure of the rotor and stator, deformation or
melting of parts and components of the product,
darkening or charring of the electric motor wires
under the action of high temperature.
c) When using the product in conditions of high
intensity work and super heavy loads.
d) For preventive and maintenance works, for
excample: lubrication, flushing.
e) Tool malfunctions due to the use of
accessories, associated and spare parts that
are not original accessories/parts of the ZUBR.
f) Mechanical damage (cracks, chips, etc.) and
damage caused by exposure to corrosive
environments, high temperature and high
humidity, the ingress of foreign objects into the
ventilation opening tool and also damage
caused by improper storage and corrosion of
metal parts.

www.kraftool.hk www.kraftool.hk
12 | Multipurpose Vacuum Cleaner| 13
h)The tool, the design of which has been amended
or supplemented.
i)Insignificant deviation from the declared
properties of the instrument, which does not
affect its value and the possibility of its intended
use.
j)For a tool that has been opened or revised
during the warranty period outside of authorized
service centers.
2) The elimination of faults recognized by us as a
warranty case is carried out at the choice of 3Y6P
company by repairing or replacing the productt
with a new one (possibly with a next generation
model). Replaced product and its parts become
the property of the company.
3) Warranty claims are accepted within the
warranty period. To do this, submit or send the
defective instrument to the service center,
enclosing the completed warranty certificate
confirming the date of purchase of the goods and
its name. A product transferred to a dealer or
service center in a partially or fully disassembled
form is not covered by the warranty. All risks of
transferring and shipping the product to the dealer
or service center are borne by the product owner.
4) Other claims, other than the said right to free
repair of the defects of the instrument, are not
covered by the warranty.
5) All power tools require regular maintenance.
The maintenance interval is equal to the service
life of the carbon brush set.
6) The service life of the product is 5 years.
POSSIBLE FAULTS AND ELIMINATION METHODS
Fault Possible cause Trouble shooting
Vacuum cleaner does not turn on
No mains voltage Check electrical connection
Incorrect mode of operation.Correctly set the switch
A connected power tool has too little power.Turn switch 8 to position “II”
Dust enters the upper section of
the vacuum cleaner.
Install or replace the filter with a
new one.
Strong reduction in power or
stopping suction
Clean or replace filter
Clean or drain the tank
Missing or damaged filter
Clogged filter, hose or nozzle
Tank overflowed
Operation Manual
4) Warranty does not cover:
a) Parts subject to working and other types of
normal wear and tear, as well as equipment
malfunction caused by these types of wear, and
the product, which has the full development of
the resource, strong external or internal
pollution.
b) Tool malfunctions caused by non-compliance
with the Op
c) Accessories, wear parts and consumables that
failed due to normal wear, such as: drive belts,
battery packs, barrels, guide rollers, protective
covers, collets, cartridges, soles, saw chains,
saw tires, sprockets, tires, carbon brushes ,
knives, sawing, abrasives, drills, trimmer line,
etc.
g) Accessories, wear parts and consumables that
failed due to normal wear, such as: drive belts,
battery packs, barrels, guide rollers, protective
covers, collets, cartridges, soles, saw chains,
saw tires, sprockets, tires, carbon brushes ,
knives, sawing, abrasives, drills, trimmer line,
etc.