KRAFTtech 241-9853 User manual

OPERATING MANUAL
Compact Circular Saw
241-9853
IMPORTANT:
Carefully read this Owner’s Manual before using this tool. Pay close atten-
tion to all Safety Instructions, Warnings, and Caution sections. Use this tool
properly, and only for its intended use
.
Safety symbols in this Manual are used to flag possible dangers. The safety
symbols and their explanations require the operator’s full understanding. The
safety warnings do not, by themselves, eliminate any danger, and they are not a
substitute for proper accident prevention measures.
This Safety Alert Symbol indicates caution, warning, or danger. Failure to obey
a safety warning can result in serious injury to yourself or others. To reduce the risk
of injury, fire, or electric shock, always follow the safety precautions.

2
TABLE OF CONTENTS
Specifications……………..…………………………………………… Page 2
Rules for Safe Operation……………..…………………………………Page 3
Description……………..……………………………………………... Page 8
Adjustments……………..………………………………………….... Page 13
Operation……………..…………………………………………….....Page 14
Maintenance……………..………………………………………….... Page 18
Troubleshooting……………..……………………………………….. Page 18
Exploded View……………..…………………………………………. Page 19
Parts List……………..……………………………………………..... Page 20
Warranty……………..……………………………………………......Page 22
SPECIFICATIONS
Model 241-9853
Rated Voltage 120V~ 60Hz
Rated Power Input 12 A
No Load Speed, n05500/min
Saw Blade Size 7 1/4”
Cutting Angle 0°~45°
Depth of Cut at 90° 2 1/2”
Depth of Cut at 45° 1 3/4”

3
RULES FOR SAFE OPERATION
KNOW THE TOOL
To operate this tool, carefully read this Owner’s Manual and all labels affixed to
the saw before using. Keep this Manual available for future reference.
IMPORTANT
This tool should only be serviced by a qualified service technician. For more
information, call the toll-free helpline, at 1-866-869-4090.
READ ALL INSTRUCTIONS THOROUGHLY
GENERAL SAFETY RULES FOR ALL POWER TOOLS
Read and understand all instructions. Failure to follow all instructions list-
ed below may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
GENERAL SAFETY PRECAUTIONS
WORK AREA
Keep the work area clean and well lit. Cluttered benches and dark areas
invite accidents.
Do not operate power tools in an explosive environment, such as in the
presence of flammable liquids, gases, or dust. Power tools create sparks
which may ignite dust or fumes.
Keep bystanders, children, and visitors away while operating a power
tool.Distractions can cause you to lose control.
ELECTRICAL SAFETY
Double insulated tools are equipped with a polarized plug (one blade is
wider than the other.) This plug will fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified
electrician to install a polarized outlet. Do not
change the plug in any way. Double insulation
eliminates the need for the three wire grounded
power cord and grounded power supply system.
Avoid body contact with grounded surfaces such
as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is
grounded.
120V ~ 60Hz

4
Don’t expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord to carry the tools or pull
the plug from an outlet. Keep cord away from heat, oil, sharp edges
or moving parts. Replace damaged cords immediately. Damaged cords
increase the risk of electric shock.
When operating a power tool outside, use an outdoor extension cord
marked “W-A” or “W”. These cords are rated for outdoor use and reduce the risk
of electric shock. The following table shows the correct size to use, depending on
cord length and nameplate amperage rating of the tool. When in doubt, use the
next heavier gauge. Always use UL and CSA listed extension cords.
Recommended sizes of extension cords
Tool’s Ampere rating Volts
Total length of cord in feet
Cord size in A. W. G.(minimum)
25’ 50’ 100’ 150’
0-6
120
V~
18 16 16 14
6-10 18 16 14 12
10-12 16 16 14 12
12-16 14 12 Not Recommended
PERSONAL SAFETY
Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use tool while tired or under the
influence of drugs, alcohol, or medication. A moment of inattention while
operating power tools may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long
hair. Keep your hair, clothing, and gloves away from moving parts.
Loose clothes, jewelry, or long hair can be caught in moving parts.
Avoid accidental starting. Be sure switch is off before plugging in.
Carrying tools with your finger on the switch or plugging in tools that have
the switch on invites accidents.
Remove adjusting keys or wrenches before turning the tool on.A wrench or
a key that is left attached to a rotating part of the tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times.Proper
footing and balance enables better control of the tool in unexpected situations.
Use safety equipment. Always wear eye protection.Dust mask, non-skid safety
shoes, hard hat, or hearing protection must be used for appropriate conditions.
Before connecting the tool to a power source (receptacle, outlet,
etc.), be sure voltage supplied is the same as that specified on the

5
nameplate of the tool. A power source with voltage greater than that
specified for the tool can result in serious injury to the user – as well as
damage to the tool.
TOOL USE AND CARE
Use clamps or other practical way to secure and support the workpiece
to a stable platform. Holding the work by hand or against your body is
unstable and may lead to loss of control.
Do not force tool. Use the correct tool for your application. The correct
tool will do the job better and safer at the rate for which is designed.
Do not use tool if switch does not turn it on or off. Any tool that cannot be
controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive
safety measures reduce the risk of starting the tool accidentally.
Store idle tools out of reach of children and other untrained persons.
Tools are dangerous in the hands of untrained users.
Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools, with sharp cutting edges are less likely to bind and are
easier to control.
Check for misalignment or binding of moving parts, breakage of parts,
and any other condition that may affect the tools operation. If damaged,
have the tool serviced before using. Many accidents are caused by poorly
maintained tools.
Use only accessories that are recommended by the manufacturer for
your model. Accessories that may be suitable for one tool, may become
hazardous when used on another tool.
Do not alter or misuse tool. These tools are precision built. Any alteration or
modification not specified is misuse and may result in a dangerous condition.
Service
Tool service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel could result in
a risk of injury.
When servicing a tool, use only identical replacement parts. Follow
instructions in the Maintenance section of this manual. Use of unauthorized
parts or failure to follow Maintenance Instructions may create a risk of electric
shock or injury.

6
SPECIFIC SAFETY RULES FOR CIRCULAR SAWS
DANGER! Keep hands away from cutting area and blade. Keep your sec-
ond hand on auxiliary handle, or motor housing.If both hands are holding the
saw, they cannot be cut by the blade.
Keep your body positioned to either side of the saw blade, but not
in line with the saw blade. KICKBACK could cause the saw to jump
backwards.
Do not reach underneath the work. The guard can not protect you from
the blade below the work.
Check lower guard for proper closing before each use. Do not operate
saw if lower guard does not move freely and close instantly. Never
clamp or tie the lower guard into the open position. If saw is accidentally
dropped, lower guard may be bent. Raise the lower guard with the Retracting
Handle and make sure it moves freely and does not touch the blade or any
other part, in all angles and depths of cut.
Check the operation and condition of the lower guard spring. If the
guard and the spring are not operating properly, they must be serviced
before use. Lower guard may operate sluggishly due to damaged parts,
gummy deposits, or a buildup of debris.
Lower guard should be retracted manually only for special cuts
such as “Pocket Cuts” and “Compound Cuts”. Raise lower guard by
Retracting Handle. As soon as blade enters the material, lower guard
must be released. For all other sawing, the lower guard should operate
automatically.
Always observe that the lower guard is covering the blade before
placing saw down on bench or floor. An unprotected, coasting blade will
cause the saw to walk backward, cutting whatever is in its path. Be aware of
the time it takes for the blade to stop after switch is released.
NEVER hold piece being cut in your hands or across your leg. It is
important to support the work properly to minimize body exposure, blade
binding, or loss of control.
Hold tool by insulated gripping surfaces when performing an operation
where the cutting tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal parts of the tool
“live” and shock the operator.
When ripping always use a rip fence or straight edge guide. This
improves the accuracy of cut and reduces the chance for blade binding.
Always use blades with correct size and shape (diamond vs. round)
arbor holes. Blades that do not match the mounting hardware of the saw

7
will run eccentrically causing loss of control.
Never use damaged or incorrect blade washers or bolts. The blade
washers and bolt were specially designed for your saw, for optimum
performance and safety of operation.
Causes and operator prevention of kickback:
Kickback is a sudden reaction to a pinched, bound or misaligned saw blade,
causing an uncontrolled saw to lift up and out of the workpiece toward the
operator.
When the blade is pinched or bound tightly by the kerf closing down, the blade
stalls and the motor reaction drives the unit rapidly back toward the operator.
If the blade becomes twisted or misaligned in the cut, the teeth at the back
edge of the blade can dig into the top surface of the wood causing the blade to
climb out of the kerf and jump back toward operator.
Kickback is the result of tool misuse and/or incorrect operating procedures or
conditions and can be avoided by taking proper precautions as given below:
Maintain a firm grip with both hands on the saw and position your
body and arm to allow you to resist KICKBACK forces. KICKBACK forces
can be controlled by the operator, if proper precautions are taken.
When blade is binding, or when interrupting a cut for any reason,
release the trigger and hold the saw motionless in the material until
the blade comes to a complete stop. Never attempt to remove the saw
from the work or pull the saw backward while the blade is in motion or
KICKBACK may occur. Investigate and take corrective actions to eliminate
the cause of blade binding.
When restarting a saw in the workpiece, center the saw blade in the
kerf and check that saw teeth are not engaged into the material. If saw
blade is binding, it may walk up or KICKBACK from the workpiece as the saw
is restarted.
Support large panels to minimize the risk of blade pinching and
KICKBACK. Large panels tend to sag under their own weight. Supports must
be placed under the panel on both sides near the line of cut and near the
edge of the panel.
Do not use dull or damaged blade. Unsharpened or improperly set blades
produce narrow kerf causing excessive friction, blade binding and KICKBACK.
Blade depth and bevel adjusting locking levers must be tight and
secure before making cut. If blade adjustment shifts while cutting, it may
cause binding and KICKBACK.
Use extra caution when making a “Pocket Cut” into existing walls or
other blind areas. The protruding blade may cut objects that can cause

8
KICKBACK.
Do not use the circular saw near fumes or combustible liquids.
Never slow the blade down with your hands, or by applying pressure to
the side of the blade.
Never apply force! Move the circular saw forward gently and steadily.
DESCRIPTION
KNOW YOUR CIRCULAR SAW (See Fig. 1)
Before attempting to use this circular
saw, familiarize yourself with all of
its operating features and safety
requirements.
1. Lock-Off Switch
2. Spindle-lock Button
3. Main Handle
4. Front Handle
5. Lower Blade Guard
6. Blade Guard Lever
7. Depth-locking lever
8. Angle-locking knob
9. 0°~45°Bevel Gauge
10. Hexagon Blade Screw
11. Base Plate
12. Outer Flange
13. Cord Guard
14. Lock-off Button
15. Blade Wrench Storage
WARNING! DO NOT allow familiarity with the saw cause carelessness. Re-
member that one careless moment is enough to cause severe injury.
Before attempting to use any tool, be sure to become familiar with all of the
operating features and safety instructions.
APPLICATIONS
3
1
6
5
10 8
9
2
4
14
12
11
7
13 15
Fig.1

9
This saw can be used for the purpose listed below:
• Cutting all types of wood and wood products.
NOTE: The use of abrasive cut-off wheels is not recommended with this saw.
KICKBACK (Figs. 2-5)
Kickback occurs when the blade stalls rapidly and the saw is driven back
toward the operator. Blade stalling is caused by any action that pinches the
blade in the wood.
DANGER! Release the switch im-
mediately if the blade binds or the saw
stalls. Kickback could cause loss of
control of the saw. Loss of control can
lead to serious personal injury.
To guard against kickback, avoid
dangerous practices such as the
following:
• Setting blade depth incorrectly.
• Sawing into knots or nails in
workpiece.
• Twisting the blade while making
a cut.
• Making a cut with a dull, gummed
up, or improperly set blade.
• Supporting the workpiece
incorrectly.
• Forcing a cut.
• Cutting warped or wet lumber.
• Operating the tool incorrectly or
misusing the tool.
To reduce the chance of kickback,
follow these safety practices:
• Keep the blade at the correct
depth setting. The depth setting
should not extend more than 1/4”
(6.5 mm) below the material that
is being cut.
• Inspect the workpiece for knots
or nails before cutting. Never saw
Fig. 2
Fig. 3
Fig. 4
Kickback - blade set too deep
Incorrect support
No more than 1/4 inch
Correct blade depth setting = blade exposed 1/4 in.
Or less on underside of workpiece

10
• Use clean, sharp, and properly set
blades. Never make cuts with dull
blades.
• Support the workpiece properly
before beginning a cut.
• Use steady, even pressure when
making a cut. Never force a cut.
• Do not cut warped or wet lumber.
• Hold the saw firmly with both
hands and maintain a balanced
position in order to resist the
forces if kickback should occur.
WARNING! When using the saw, always stay alert and exercise control. Do
not remove the saw from the workpiece while the blade is moving.
SAW BLADES
• The best saw blades will not cut efficiently if they are not kept clean, sharp,
and properly set. Using a dull blade will place a heavy load on the saw and
increase the danger of kickback. Keep extra blades on hand so that sharp
blades are always available.
• Gum and wood pitch hardened on blades will slow the saw down. Remove
the saw blade from the saw, and use gum and pitch remover, hot water, or
kerosene to remove these accumulations. DO NOT USE GASOLINE.
Fig. 5
Correct support

11
CHANGING THE SAW BLADE
WARNING! To prevent personal injury, always disconnect the plug from the
power source before installing or and removing the saw blade!
TO REMOVE THE SAW BLADE
1. Unplug the saw.
2. Depress and hold the spindle-lock button.
3. Remove the blade screw by turning it counter-clockwise using the wrench
(included) while keeping the spindle-lock button depressed.
4. Remove the outer blade washer.
5. Lift the lower blade guard.
6. Remove the blade.
INSTALLING THE SAW BLADE (Fig. 6)
1. Unplug the saw.
2. Depress and hold the spindle-lock button.
3. Remove the blade screw by turning it counter-clockwise using the wrench
(included) while keeping the spindle lock depressed.
4. Remove outer blade washer (“D” Washer).
WARNING! If the inner flange bushing has been removed, replace it before
placing the blade on the spindle. Failure to do so will prevent the blade from
tightening properly, and could result in serious personal injury.
Fig. 6 Inner
Bushing Blade
Outer Blade Flange
Blade Screw
Spindle

12
5. Retract the lower blade guard into the upper blade guard using the lower
blade guard handle. Make sure the lower guard spring works properly,
allowing the guard to move freely.
6. Verify that the saw teeth and the arrow on the saw blade and the arrow on
the lower guard are pointing in the same direction.
NOTE: The saw teeth should point upward at the front of the saw, as shown in Fig. 6.
7. Fit the saw blade inside the lower blade guard and onto the spindle.
8. Replace the “D” washer.
9. Depress and hold the spindle-lock button, and replace the blade screw.
10. Tighten the blade screw securely by turning it clockwise using the wrench.
NOTE: Never use a blade that is too thick to allow the “D” washer to engage
with the flat section of the spindle.
BLADE GUARD SYSTEM (Fig. 7)
The lower blade guard on the circular
saw is there for the operator’s
protection and safety. Do not alter
it for any reason. If it becomes
damaged or begins to run slowly or
sluggishly, DO NOT operate the saw
until the damaged part has been
repaired or replaced. ALWAYS leave
the guard in its correct operating
position when using the saw.
DANGER! When sawing through a workpiece, the lower blade guard does not
cover the blade on the underside of the workpiece. Since the blade is exposed on
the underside of the workpiece, ALWAYS keep hands and fingers away from the
cutting area. Serious injury will result in any part of the body comes into contact
with the moving blade.
CAUTION! To avoid possible serious injury, never use the saw when the
guard is not operating correctly. Check the guard for correct operation before
each use. The guard is operating correctly when it moves freely and instantly
returns to the closed position. If the saw is dropped, check the lower blade guard
and bumper for damage at all depth settings before using it.
Fig. 7
Lower blade guard is in up position
when making a cut

13
If the lower blade guard does not snap closed at any time, unplug the saw from
the power supply. Exercise the lower guard by moving it rapidly back and forth
from the full open position to the closed position several times. This will usually
restore the guard to its normal operating condition. If this does not correct
a slow or sluggishly closing lower guard, do not use the saw. Take it to an
authorized service technician for repair.
STARTING/ STOPPING THE SAW
To start the saw: Depress lock-off button, then depress the switch trigger.
Always allow the blade reach full speed, and then guide the saw into the
workpiece.
WARNING! If the blade comes into contact with the workpiece before it
reaches full speed, this may cause the saw to “kick back” toward the operator,
resulting in serious injury.
To stop the saw: Release the switch trigger.
After releasing the switch trigger, allow the blade to come to a complete stop.
ADJUSTMENTS
DEPTH-OF-CUT ADJUSTMENT (Fig. 8)
WARNING! ALWAYS maintain the correct blade-depth setting. The correct
blade-depth setting for all cuts should not exceed the thickness of the materi-
al being cut by more than1/4” (6.5 mm). Greater blade depth will increase the
chance of kickback, and cause the cut to be rough.
1. Unplug the saw.
2. Pull depth adjustment lever
upward to release it.
3. Determine the desired depth of
cut.
4. Hold the base flat against the
workpiece, and raise or lower the
saw until the indicator mark on
the saw aligns with the desired
depth on the scale.
5. Push down on depth-adjustment
lever to lock it into position.
Fig. 8

14
ADJUSTING THE CUTTING ANGLE (Fig. 9)
1. Loosen the angle-locking knob,
which is located on the 0°-45°
bevel gauge on the base plate.
2. Tilt the body of the saw (Fig. 9)
until the required angle is reached
(refer to the scale on the 0°-45°
bevel gauge).
3. Tighten the locking knob in order
to secure the base plate.
OPERATION (Fig. 10-12)
Refer to the figures in this section to
learn the correct and incorrect ways
of handling the saw.
WARNING! To make sawing eas-
ier and safer, always maintain proper
control of the saw. Loss of control
could cause an accident resulting in
possible serious injury.
DANGER! When lifting the saw from
the workpiece, the blade is exposed on
the underside of the saw until the lower
blade guard closes. Make sure that the
lower blade guard is closed before set-
ting the saw down.
To make the best possible cut, follow
these helpful hints.
1. Hold the saw firmly with both
hands.
2. Avoid placing your hand on the
workpiece while making a cut.
3. Support the workpiece so that the
cut is always to the operator’s side.
4. Support the workpiece near the cut.
Fig. 9
Fig. 10
Fig. 11

15
5. Clamp the workpiece securely, so
that the workpiece will not move
during the cut.
6. Always place the saw on the
portion of the workpiece that is
supported, and not on the “cut
off” piece.
7. Place the workpiece with the
“good” side down.
8. Draw a guideline along the desired
cutting line before beginning the cut.
9. Keep the cord away from the cutting area. Always place the cord so that it is
not hanging up on the workpiece while making a cut.
DANGER! If the cord hangs up on the workpiece during a cut, release the
switch trigger immediately. Unplug the saw and reposition the cord in order to
prevent it from hanging up again.
DANGER! Using a saw with a damaged cord could result in serious injury or
death. If the cord has been damaged, have it replaced before using the saw again.
CROSS-CUTTING/RIP CUTTING (Fig. 13-14)
When making a cross-cut or a rip
cut, align the guideline with the full-
length kerf indicator on the base, as
shown in fig. 13. The distance from
the saw blade to the saw base is
approximately 4 1/4” (10.8 cm) on
the left side of the saw and 1 1/2”
(3.8 cm) on the right side.
Blade thicknesses vary, so you
should always make a trial cut in
scrap material along a guideline to
determine how much the guideline
must be offset from the guide in order to produce an accurate cut.
NOTE: The distance from the cutting line to the guideline is the amount by which
the guide should be offset.
Use a guide when making long or wide rip cuts.
Fig. 12
Fig. 13
Full length
kerf indic
ator
Guideline

16
Rip cutting using a straight edge:
1. Secure the workpiece.
2. Clamp a straight edge to the
workpiece using C-clamps.
NOTE: Position the C-clamps so that
they will not interfere with the saw
housing during the cut.
3. Saw along the straight edge in order
to achieve a straight rip cut.
NOTE: Do not bind the blade in the cut.
BEVEL CUTTING
To make the best possible cut:
1. Align the cutting line with the inner-blade-guide notch on the base when
making 45° bevel cuts.
2. Make a trial cut in scrap material along a guideline in order to determine the
amount to offset the guideline on the cutting material.
3. Adjust the angle of cut to any desired setting between 0° and 45°.
Fig. 14
C-clamps
Straight edge
C-clamps
Workpiece
Guideline

17
WARNING! Attempting a bevel cut without having the bevel adjustment lever
securely locked in place can result in serious injury.
To bevel cut (Fig. 15)
1. Hold the saw firmly with both
hands, as shown.
2. Rest the front edge of the base on
the workpiece.
3. Start the saw and allow the blade
to reach full speed.
4. Guide the saw into the workpiece,
and make the cut.
5. Release the trigger, and allow the
blade to come to a complete stop.
6. Lift the saw from the workpiece.
POCKET CUTTING
WARNING! Always adjust the bevel setting to 0° before making a pocket cut.
Attempting a pocket cut at any other setting can result in loss of control of the
saw and possible serious injury.
1. Adjust the bevel setting to 0°.
2. Set the blade to the correct blade-depth setting.
3. Swing the lower blade guard up using the lower blade guard handle.
4. Hold the lower blade guard by the handle.
5. Rest the front of the base flat against the workpiece, with the rear of the
handle raised, so that the blade does not touch the workpiece.
6. Start the saw, and allow the blade to reach full speed.
7. Guide the saw into the workpiece, and make the cut.
WARNING! Always cut in a forward direction when pocket cutting. Cutting in
the reverse direction could cause the saw to climb up on the workpiece and kick
back toward the operator.
WARNING! As blade starts cutting the material, release the lower guard im-
mediately. When the foot rests flat on the surface being cut, proceed cutting in
forward direction to end of cut.
Fig. 15

18
8. Release the trigger, and allow the blade to come to a complete stop.
9. Lift the saw from the workpiece.
10. Clear the corners out with a hand saw or sabre saw.
WARNING! Never tie the lower blade guard in a raised position. Leaving the
blade exposed could lead to serious injury.
MAINTENANCE
CAUTION! Before performing maintenance or cleaning, pull the plug
from the main socket.
• Never use water or chemical liquids to clean the electrical parts of the
machine.
• Keep the ventilation slots clean in order to prevent overheating of the motor.
TROUBLESHOOTING
PROBLEM CAUSE OF THE PROBLEM SUGGESTED CORRECTIVE
ACTION
Motor does
not start. Fuse Check the time-delayed fuse or
circuit breaker.
Blade binds,
jams, or burns
the wood.
Improper operation See “OPERATION” section.
Dull blade Replace or sharpen blade.
Improper blade Replace blade.
Warped blade Replace blade.
Saw vibrates
or shakes.
Damaged blade Replace blade.
Loose blade Tighten arbor bolt.
WARNING! Turn the switch to the “OFF” position and unplug the saw from the
power source before performing troubleshooting procedures.
ACCESSORIES
Blade wrench……………..……………………………………………… 1 pc

19
Exploded View
51
28
44
30
41
37
18
19
34
49
42
25
20
45
48
50
33
27
31
43
24
47
38
36
29
39
22
46
35
23
12
40
26
32
27
25
25
25
25
25
25
25
25
25
25
25
40
17
10
11
9
16
8
15
14
13
7
4
5
2
1
3
6
25
3
3
3
4
5
6
21
21
25
25
25
25
52

20
Parts List
No. Part Name Qty
1 Stator 1
2 Ball Bearing 1
3 Tapping Screw 8
4 Carbon Brush 2
5 Brush Support 2
6 Snailed Spring 2
7 Rotor 1
8 Left Housing 1
9 Felt Block 1
10 Lock Button 1
11 Spring 1
12 Spindle Lock 1
13 Bearing Support 1
14 Needle Bearing 1
15 Gear 1
16 Gear Shaft 1
17 Ball Bearing 1
18 Spring 1
19 Lower Guard Assy 1
20 Cover 1
21 Washer 4
22 Guard 1
23 Stopper 1
24 Thread forming Screw 1
25 Tapping Screw 17
26 Switch 1
27 Tapping Screw 2
Table of contents