Kramer KDOCK-1-HOLDER User manual

www.kramerAV.com
[e-mail]
Installation Instructions
MODEL:
KDOCK-1/2/3-HOLDER
KDOCK-4-HOLDER
P/N:
2900- 301522QS
Rev:
3
SAFETY WARNING
Disconnect the unit from the power supply before opening and servicing
For the latest information on our products and a list of Kramer distributors, visit our
Web site where updates to these installation instructions may be found.
We welcome your questions, comments, andfeedback.

2
KDOCK-1/2/3-HOLDER
KDOCK-1/2/3-HOLDER
Congratulations on purchasing your Kramer KDOCK-1/2/3-HOLDER / KDOCK-4-HOLDER
for safely securing KDock USB-C Hub Multiport Adapters below or on a surface.
This document describes how to secure the KDOCK-1/2/3-HOLDER and the
KDOCK-4-HOLDER to a surface.
Installing the KDOCK-1/2/3-HOLDER
KDOCK-1/2/3-HOLDER can be installed either under or above a surface. In this example,
it is installed under a table.
To secure the KDOCK-1/2/3-HOLDER under a table:
1. Insert the KDock device into the clamp, in-between the rubber pads.
2. Insert a washer (supplied) and then a nut (supplied) onto each of the studs and tighten.
3. Check the location under the table where you want to install the device and mark the
location for the two installation screws (supplied).
4. Use the two installation screws to secure the KDOCK-1/2/3-HOLDER under the table.
KDOCK-1/2/3-HOLDER is secured under a table.

Installation Instructions
3
Installing the KDOCK-4-HOLDER
KDOCK-4-HOLDER can be installed either under or above a surface. In this example, it is
installed on a table. Note that when it is installed under, the flip-up device holder cannot be
used.
To secure the KDOCK-4-HOLDER on a table:
1. Place the KDock-4 device on the surface, at the correct location.
2. Place the KDOCK-4-HOLDER over the device.
3. Insert the four screws and secure the KDOCK-4-HOLDER to the table.
KDOCK-4-HOLDER is secured on a table.

4
KDOCK-1/2/3-HOLDER
Technical Specifications
Environmental
Conditions
Operating Temperature
0° to +40°C (32° to 104°F).
Storage Temperature
-10° to +55°C (14° to 131°F).
Humidity
5% to 90%, RHL non-condensing.
Regulatory
Compliance
Safety
CE.
Environmental
RoHs
Enclosure
Materials
Zinc-coated steel and rubber padding (for
KDOCK-1/2/3-HOLDER only)
General
Net Dimensions
(W, D, H)
KDOCK-1/2/3-HOLDER: 3cm x 6.5cm x 1.9 cm
(1.2" x 2.6" x 0.75") Approx.
KDOCK-4-HOLDER: 26.2cm x 7.1cm x 2.5cm
(10.3" x 2.8" x 1") Approx.
Shipping Dimensions
(W, D, H)
KDOCK-1/2/3-HOLDER: 12.1cm x 8.2cm x 4.1cm
(4.8" x 3.2" x 1.6")
KDOCK-4-HOLDER: 36.6cm x 21cm x 7.7 cm
(14.4" x 8.27" x 3")
Net Weight
KDOCK-1/2/3-HOLDER: 50g (0.11lbs) approx.
KDOCK-4-HOLDER: 201g (0.44lbs) approx.
Shipping Weight
KDOCK-1/2/3-HOLDER: 90g (0.2lbs) approx.
KDOCK-4-HOLDER: 261g (0.6lbs) approx.