Kramer K-CAM-USB User manual

K-CAM-USB Quick Start
P/N:
2900- 301474QS
Rev:
2
Scan for full manual
K-CAM-USB Quick Start Guide
This guide helps you install and use your K-CAM-USB for the first time.
Go to www.kramerav.com/downloads/K-CAM-USB to download the latest user manual and check if
firmware upgrades are available.
Step 1: Check what’s in the box
K-CAM-USB Full HD Conference Camera
1 Wall bracket
1 USB-B to USB-A cable
1 Power adapter
1 Set of installation screws
1 RS-232 VISCA (m) to 9-pin (f) cable
Remote control transmitter with batteries
1 Terminal block plug
Quick start guide
Step 2: Get to know your K-CAM-USB
#
Feature
Function
1
HDMI™Connector
Connect to a display.
2
USB Type-B Connector
Connect to computer or collaboration device using the included USB-B to USB-A
cable. We recommend connecting K-CAM-USB to a USB 3.0 connector on your
computer or collaboration device.
3
LINE 3.5mm Mini Jack
Connect to a microphone.
4
SYSTEM SELECT Rotary
DIP-Switches
Set the video resolution. By default, it is set to “F” = video resolution is set via the
remote control or web pages.
5
RS232 IN/OUT VISCA Connector
Connect to a camera controller using the included RS-232 VISCA (m) to 9-pin (f)
cable.
6
RS422/RS485 4-pin term. block
Not in use.
7
LAN RJ-45 Connector
Connect to your network or directly to a computer.
8
DC12V Power Connector
Connect to the 12V power adapter.
9
ON/OFF Switch
Turn the unit on and off.

Step 3: Mount K-CAM-USB
Install K-CAM-USB using one of the following methods:
•Attach the rubber feet and place the unit on a flat
surface.
Use the included wall bracket to attach it to a wall as
follows:
•Ensure that the environment (e.g., maximum ambient temperature & air flow) is
compatible for the device.
•Avoid uneven mechanical loading.
•Appropriate consideration of equipment nameplate ratings should be used for
avoiding overloading of the circuits.
•Reliable earthing of rack-mounted equipment should be maintained.
•Maximum mounting height for the device is 2 meters.
1. Drill 4 holes and fasten the bolts to the wall.
2. Fasten the stabilization pin to the upper surface of the bracket and
attach the rubber pad to the bracket.
3. Attach the bracket to the wall.
4. Fasten the bracket to the wall with the 4 washers and
nuts.
5. Place K-CAM-USB on the bracket, inserting the peg into the hole
on the underside of the camera base and fasten the camera to the
bracket with the screw.

Step 4: Connect inputs and outputs
Always switch OFF the power on each device before connecting it to your K-CAM-USB.
Step 5: Connect power
Connect the power adapter to K-CAM-USB and plug it
into the mains electricity.
Safety Instructions (See www.kramerav.com for updated safety information)
Caution:
•For products with relay terminals and GPI\O ports, please refer to the
permitted rating for an external connection, located next to the terminal or
in the User Manual.
•There are no operator serviceable parts inside the unit.
Warning:
•Use only the power cord that is supplied with the unit.
•Disconnect the power and unplug the unit from the wall before installing.
Step 6: Operate K-CAM-USB
Operate K-CAM-USB via:
•Using the IR remote control
transmitter.
•Remotely, embedded web
pages via the Ethernet.
•Remotely, by RS-232 serial
commands transmitted by a
touch screen system, PC, or
other serial controller.
RS-232 Control
Baud Rate:
115,200
Parity:
None
Data Bits:
8
Command Format:
ASCII
Stop Bits:
1
Default Ethernet Parameters
Ports
IP Address:
192.168.1.39
Data: 3000
Web: 80
Subnet Mask:
255.255.0.0
Onvif: 2000
Soap: 1936
Gateway:
0.0.0.0.
RTMP: 1935
Rtsp: 554
UDP Port #:
50000
Visca: 1259
WebSocket: 8088
TCP Port #:
5000
Default Username:
admin
Default Password:
admin
Pairing the remote control to K-CAM-USB
You must perform pairing before using the remote control.
•Press the SET and * keys simultaneously for 3 seconds.
The remote control LED flashes and pairing is complete.
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.