KRESS KG347E User manual

Cordless Chainsaw
Akku-Kettensäge
Tronçonneuse sans l
Sega a catena senza lo
Motosierra inalámbrica
Draadloze kettingzaag
Batteridreven motorsav
Аккумуляторная цепная пила
Sladdlös motorsåg
EN
D
F
I
ES
NL
DK
RU
SV
P07
P20
P35
P50
P66
P82
P97
P111
P127
KG347E KG347E.X

22
23
18 19 20 1721
1
4
5
6
7
10
2
3
9
8
15
16
14
11 12
13

C2C1
B2B1
A2A1
2
1
24
1
2
Kink

E1D
FE2
HG
1
2
Bar
3-5mm
100%
0%

NM
L
K
JI
1
2
Click!
1
2
Click!
1
2

Z
Z
Y
Y
aInjecting grease to lubricate
S
R
Q
PO
T

7
EN
TABLE OF CONTENTS
Introduction......................................................................................................................................................7
Safety Instructions........................................................................................................................................8
Component List...........................................................................................................................................13
Specications...............................................................................................................................................13
Assembly........................................................................................................................................................14
Operation.......................................................................................................................................................15
Maintenance.................................................................................................................................................17
Environmental Protection........................................................................................................................18
Troubleshooting...........................................................................................................................................19
Declaration of Conformity........................................................................................................................19
INTRODUCTION
Dear Customer,
Thank you for buying this Kress product. We are dedicated to developing high quality
products to meet your lawn & garden requirements.
The Kress brand is synonymous with premium quality service. Over the years of
your products life, if you have any questions or concerns about your product, please
contact your location of purchase or our Customer Service Team for assistance.
We are condent you will enjoy working with your Kress product for years to come.
INTENDED USE OF CHAINSAW
The Chainsaw is intended for sawing of trees, tree trunks, branches, wooden beams,
planks, etc. Cuts can be sawed with or across the grain. This product is not suitable
for sawing mineral materials.

8
EN
ORIGINAL INSTRUCTIONS
PRODUCT SAFETY
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING Read all safety warnings,
instructions, illustrations and
specifications provided with this power
tool. Failure to follow all instructions listed below
may result in electric shock, re and/or serious
injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1. WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or
fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2. ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodied plugs and matching outlets
will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges
and refrigerators. There is an increased risk
of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock .
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock .
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply . Use of an RCD
reduces the risk of electric shock.
3. PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the influence of drugs, alcohol
or medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your nger on the switch or energising
power tools that have the switch on invites
accidents .
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving
parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dust-
related hazards.
h) Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action
can cause severe injury within a fraction of a
second.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch
does not turn it on and off . Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or remove the battery pack, if detachable,
from the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation . If

9
EN
damaged, have the power tool repaired before
use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow
for safe handling and control of the tool in
unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of re
when used with another battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and re.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from
one terminal to another. Shorting the battery
terminals together may cause burns or a re.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause
irritation or burns.
e) Do not use a battery pack or tool that is
damaged or modified. Damaged or modied
batteries may exhibit unpredictable behaviour
resulting in re, explosion or risk of injury.
f) Do not expose a battery pack or tool to fire
or excessive temperature . Exposure to re or
temperature above 130 °C may cause explosion.
g) Follow all charging instructions and do
not charge the battery pack or tool outside
the temperature range specified in the
instructions. Charging improperly or at
temperatures outside the specied range may
damage the battery and increase the risk of re.
6. SERVICE
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the
power tool is maintained.
b) Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
1) GENERAL CHAIN SAW
SAFETY WARNINGS:
a) Keep all parts of the body away from the saw
chain when the chain saw is operating. Before
you start the chain saw, make sure the saw
chain is not contacting anything. A moment of
inattention while operating chain saws may cause
entanglement of your clothing or body with the
saw chain.
b) Always hold the chain saw with your right
hand on the rear handle and your left hand on
the front handle. Holding the chain saw with a
reversed hand conguration increases the risk of
personal injury and should never be done.
c) Hold the chain saw by insulated gripping
surfaces only, because the saw chain may
contact hidden wiring . Saw chains contacting a
“live”wire may make exposed metal parts of the
chain saw “live”and could give the operator an
electric shock.
d) Wear safety glasses protection. Further
protective equipment for hearing, head,
hands, legs and feet is recommended.
Adequate protective clothing will reduce personal
injury by ying debris or accidental contact with
the saw chain.
e) Do not operate a chain saw in a tree, on
a ladder, from a rooftop, or any unstable
support. Operation of a chain saw in this manner
could result in serious personal injury.
f) Always keep proper footing and operate
the chain saw only when standing on fixed,
secure and level surface. Slippery or unstable
surfaces may cause a loss of balance or control
of the chain saw.
g) When cutting a limb that is under tension , be
alert for spring back. When the tension in the
wood bres is released , the spring loaded limb
may strike the operator and/or throw the chain
saw out of control.
h) Use extreme caution when cutting brush and
saplings. The slender material may catch the
saw chain and be whipped toward you or pull
you off balance.
i) Carry the chain saw by the front handle with
the chain saw switched off and away from
your body. When transporting or storing the
chain saw , always fit the guide bar cover.
Proper handling of the chain saw will reduce the
likelihood of accidental contact with the moving
saw chain.
j) Follow instructions for lubricating, chain
tensioning and changing the bar and chain.
Improperly tensioned or lubricated chain may
either break or increase the chance for kickback.
k) Cut wood only. Do not use chain saw for
purposes not intended. For example: do
not use chain saw for cutting metal, plastic,
masonry or non-wood building materials . Use
of the chain saw for operations different than
intended could result in a hazardous situation.
l) Do not attempt to fell a tree until you have an
understanding of the risks and how to avoid
them. Serious injury could occur to the operator

10
EN
or bystanders while felling a tree.
m) Follow all instructions when clearing jammed
material, storing or servicing the chain saw.
Make sure the switch is off and the battery
pack is removed. Unexpected actuation of the
chain saw while clearing jammed material or
servicing may result in serious personal injury.
n) Recommendation that the first-time user
should, as a minimum, practise cutting logs
on a saw-horse or cradle.
o) Recommendation to have sharpening and
maintenance of the saw chain performed by
authorised service centres.
2) CAUSES AND OPERATOR
PREVENTION OF
KICKBACK:
Kickback may occur when the nose or tip of the
guide bar touches an object, or when the wood
closes in and pinches the saw chain in the cut.
Tip contact in some cases may cause a sudden
reverse reaction, kicking the guide bar up and back
towards the operator.
Pinching the saw chain along the top of the guide
bar may push the guide bar rapidly back towards
the
operator.
Either of these reactions may cause you to lose
control of the saw which could result in serious
personal
injury. Do not rely exclusively upon the safety
devices built into your saw. As a chain saw user, you
should take several steps to keep your cutting jobs
free from accident or injury.
Kickback is the result of chain saw misuse and/or
incorrect operating procedures or conditions and
can be
avoided by taking proper precautions as given
below:
a) Maintain a firm grip, with thumbs and fingers
encircling the chain saw handles, with both
hands on the saw and position your body
and arm to allow you to resist kickback
forces. Kickback forces can be controlled by the
operator, if proper precautions are taken. Do not
let go of the chain saw.
b) Do not overreach and do not cut above
shoulder height. This helps prevent unintended
tip contact and enables better control of the
chain saw in unexpected situations.
c) Only use replacement bars and chains
specified by the manufacturer. Incorrect
replacement guide bars and saw chains may
cause chain breakage and/or kickback.
d) Follow the manufacturer’s sharpening and
maintenance instructions for the saw chain.
Decreasing the depth gauge height can lead to
increased kickback.
Residual risks
Even with the intended use of the appliance there
is always a residual risk, which can not prevented.
According to the type and construction of the
appliance the following potential hazards might
apply:
- Contact with exposed saw teeth of the saw chain
(cutting hazards)
- Access to the rotating saw chain (cutting
hazards)
- Unforeseen, abrupt movement of the guide bar
(cutting hazards)
- Flung out of parts from the saw chain (Cutting /
injection hazards)
- Flung out of parts of the work piece
- Skin contact with the oil
- Loss of hearing, if no required ear protection
used during work
SAFETY WARNINGS FOR
BATTERY PACK
a) Do not dismantle, open or shred cells or
battery pack.
b) Do not short-circuit a battery pack. Do not
store battery packs haphazardly in a box or
drawer where they may short-circuit each
other or be short-circuited by conductive
materials. When battery pack is not in use,
keep it away from other metal objects, like paper
clips, coins, keys, nails, screws or other small
metal objects, that can make a connection from
one terminal to another. Shorting the battery
terminals together may cause burns or a re.
c) Do not expose battery pack to heat or fire.
Avoid storage in direct sunlight.
d) Do not subject battery pack to mechanical
shock.
e) In the event of battery leaking, do not allow
the liquid to come into contact with the skin
or eyes. If contact has been made, wash the
affected area with copious amounts of water
and seek medical advice.
f) Keep battery pack clean and dry.
g) Wipe the battery pack terminals with a clean
dry cloth if they become dirty.
h) Battery pack needs to be charged before use.
Always refer to this instruction and use the
correct charging procedure.
i) Do not maintain battery pack on charge when
not in use.
j) After extended periods of storage, it may
be necessary to charge and discharge
the battery pack several times to obtain
maximum performance.
k) Recharge only with the charger specified by
Kress. Do not use any charger other than
that specifically provided for use with the
equipment.
l) Do not use any battery pack which is not
designed for use with the equipment.
m) Keep battery pack out of the reach of
children.

11
EN
n) Retain the original product literature for future
reference.
o) Remove the battery from the equipment when
not in use.
p) Dispose of properly.
q) Do not mix cells of different manufacture,
capacity, size or type within a device.
r) Keep the battery away from microwaves and
high pressure.
SAVE THESE INSTRUCTIONS
Instructions concerning the proper techniques
for basic felling, limbing, and cross-cutting
1. Felling a tree
When bucking and felling operations are being
performed by two or more persons at the same time,
the felling operations should be separated from the
bucking operation by a distance of at least twice the
height of the tree being felled. Trees should not be
felled in a manner that would endanger any person,
strike any utility line or cause any property damage.
If the tree does make contact with any utility line, the
company should be notied immediately.
The Chainsaw operator should keep on the uphill
side of the terrain as the tree is likely to roll or slide
downhill after it is felled.
An escape path should be planned and cleared as
necessary before cuts are started. The escape path
should extend back and diagonally to the rear of the
expected line of fall as illustrated in Figure 1.
Before felling is started, consider the natural lean of
the tree, the location of larger branches and the wind
direction to judge which way the tree will fall.
Remove dirt, stones, loose bark, nails, staples and
wire from the tree.
2. Notching undercut
Make the notch 1/3 the diameter of the tree,
perpendicular to the direction of falls as illustrated in
Figure 1. Make the lower horizontal notching cut (W)
rst. This will help to avoid pinching either the saw
chain or the guide bar when the second notch (X) is
being made.
3. Felling back cut
Make the felling back cut (Y) at least 50 mm higher
than the horizontal notching cut as illustrated in
Figure 1. Keep the felling back cut parallel to the
horizontal notching cut. Make the felling back cut
so enough wood is left to act as a hinge. The hinge
wood keeps the tree from twisting and falling in the
wrong direction. Do not cut through the hinge.
As the felling gets close to the hinge, the tree should
begin to fall. If there is any chance that the tree may
not fall in desired direction or it may rock back and
bind the saw chain, stop cutting before the felling
back cut is complete and use wedges of wood,
plastic or aluminium (Z) to open the cut and drop the
tree along the desired line of fall ( ).
When the tree begins to fall remove the Chainsaw
from the cut, stop the motor, put the Chainsaw
down, then use the retreat path planned ( ). Be
alert for overhead limbs falling and watch your
footing. (See Figure 1)
3
22
W
YZ
X
50mm
50mm
1
1
1
2
2/3
1
1/3
12
2/3
1/3
Figure 1
4. Limbing a tree
Limbing is removing the branches from a fallen tree.
When limbing leave larger lower limbs to support the
log off the ground. Remove the small limbs in one
cut as illustrated in Figure 2. Branches under tension
should be cut from the bottom up to avoid binding
the Chainsaw.
3
22
W
YZ
X
50mm
50mm
1
1
1
2
2/3
1
1/3
12
2/3
1/3
Figure 2
5. Bucking a log
Bucking is cutting a log into lengths. It is important
to make sure your footing is rm and your weight is
evenly distributed on both feet. When possible, the
log should be raised and supported by the use of
limbs, logs or chocks. Follow the simple directions
for easy cutting.
When the log is supported along its entire length
as illustrated in Figure 3, it is cut from the top
(overbuck), avoid contacting ground as this will
greatly reduce the chain sharpness.
3
22
W
YZ
X
50mm
50mm
1
1
1
2
2/3
1
1/3
12
2/3
1/3
Figure 3
When the log is supported on one end, as illustrated
in Figure 4, cut 1/3 the diameter from the underside
( underbuck) (1). Then make the nished cut by
overbucking (2) to meet the rst cut.

12
EN
3
22
W
YZ
X
50mm
50mm
1
1
1
2
2/3
1
1/3
12
2/3
1/3
Figure 4
When the log is supported on both ends, as
illustrated in Figure 5, cut 1/3 the diameter from the
top (overbuck) (1). Then make the nished cut by
underbucking (2) the lower 2/3 to meet the rst cut.
3
22
W
YZ
X
50mm
50mm
1
1
1
2
2/3
1
1/3
12
2/3
1/3
Figure 5
When bucking on a slope always stand on the uphill
side of the log, as illustrated in Figure 6. When
“cutting through”, to maintain complete control
release the cutting pressure near the end of the cut
without relaxing your grip on the Chainsaw handles.
Don’t let the chain contact the ground. After
completing the cut, wait for the saw chain to stop
before you move the Chainsaw. Always stop the
motor before moving from tree to tree.
3
22
W
YZ
X
50mm
50mm
1
1
1
2
2/3
1
1/3
12
2/3
1/3
Figure 6
SYMBOLS
To reduce the risk of injury, user
must read instruction manual
WARNING
Wear ear protection
Wear eye protection
Wear dust mask
Always use chain saw two-handed
Beware of chain saw kickback and
avoid contact with bar tip
Do not expose to rain
Wear head protection
Wear protective gloves
Wear protective footwear
Waste electrical products must
not be disposed of with household
waste. Please recycle where
facilities exist. Check with your local
authorities or retailer for recycling
advice.
Li-Ion battery This product has been
marked with a symbol relating to
‘separate collection’ for all battery
packs and battery pack. It will
then be recycled or dismantled in
order to reduce the impact on the
environment. Battery packs can be
hazardous for the environment and
for human health since they contain
hazardous substances.

13
EN
Do not burn
Batteries may enter water cycle if
disposed improperly, which can
be hazardous for ecosystem. Do
not dispose of waste batteries as
unsorted municipal waste.
Unlock
Lock
COMPONENT LIST
1. REAR HANDLE
2. ON/OFF SWITCH
3. POWER INDICATOR LIGHT
4. FRONT HANDLE
5. CHAIN BRAKE LEVER (HAND GUARD)
6. CHAIN
7. GUIDE BAR
8. CHAIN TENSIONING KNOB
9. CHAIN COVER
10. REAR HAND GUARD
11. BATTERY PACK*
12. BATTERY PACK RELEASE BUTTON*
13. LOCK-OUT BUTTON
14. OIL LEVEL WINDOW
15. OIL FILLER CAP
16. BUMPER SPIKE
17. BAR AND CHAIN STORAGE/ TRANSPOR-
TATION COVER (SHEATH)
18. DRIVE SPROCKET
19. BAR PAD
20. FASTENING BAR BOLT
21. BAR LOCATING TABS
22. OIL OUTLET
23. CHAIN DIRECTION SYMBOL
24. BAR TENSIONING PLATE (SEE FIG. A2)
* Not all the accessories illustrated or described
are included in standard delivery.
TECHNICAL DATA
Type KG347E KG347E.X (3 - designation of ma-
chinery, representative of Chainsaw)
KG347E KG347E.X **
Voltage 40V Max.(2x20V Max.) ***
Bar length 40 cm
Chain speed 18 m/s
Oil tank capacity 160 ml
Chain pitch 0.95 cm
Number of chain
drive links 56
Chain gauge 1.1 mm
Replacement
chain ES: 3/8LP.043 56E 90X/ Oregon: 90PX056
Replacement bar ES: ES164SDEA041/Oregon:
164MLEA041
Battery type Lithium-Ion
Machine Weight
(bare tool) 4.2 kg
** X=1-999，A-Z，M1-M9 there are only used for dif-
ferent customers, there are no safe relevant changes
between these models.
*** Voltage measured without workload. Initial battery
voltage reaches maximum of 20 volts. Nominal volt-
age is 18 volts.
Category Type Capacity
20V Battery KAB04 4.0 Ah
20V Charger KAC04 4.0 A
We recommend that you purchase your accessories
listed in the above list from the same store that sold
you the tool. Refer to the accessory packaging for
further details. Store personnel can assist you and
offer advice.
NOISE INFORMATION
A weighted sound pressure L
pA
= 85.9 dB(A)
A weighted sound power L
wA
= 101.2 dB(A)
KpA & KwA
3 dB(A)
Wear ear protection

14
EN
VIBRATION INFORMATION
Vibration total values (triax vector sum) determined
according to EN 62841:
Vibration emission value
ah= 4.8 m/s2Uncertainty K = 1.5m/s²
The declared vibration total value and the declared
noise emission value have been measured in
accordance with a standard test method and may be
used for comparing one tool with another.
The declared vibration total value and the declared
noise emission value may also be used in a
preliminary assessment of exposure.
WARNING: The vibration and noise emissions
during actual use of the power tool can differ
from the declared value depending on the ways
in which the tool is used especially what kind of
workpiece is processed dependant on the following
examples and other variations on how the tool is
used:
How the tool is used and the materials being cut or
drilled.
The tool being in good condition and well maintained.
The use of the correct accessory for the tool and
ensuring it is sharp and in good condition.
The tightness of the grip on the handles and if any
anti vibration and noise accessories are used.
And the tool is being used as intended by its design
and these instructions.
This tool may cause hand-arm vibration syndrome
if its use is not adequately managed.
WARNING: To be accurate, an estimation of
exposure level in the actual conditions of use
should also take account of all parts of the operating
cycle such as the times when the tool is switched off
and when it is running idle but not actually doing the
job. This may signicantly reduce the exposure level
over the total working period.
Helping to minimise your vibration and noise
exposure risk.
Always use sharp chisels, drills and blades.
Maintain this tool in accordance with these
instructions and keep well lubricated (where
appropriate).
If the tool is to be used regularly then invest in anti
vibration and noise accessories.
Plan your work schedule to spread any high vibration
tool use across a number of days.
ASSEMBLY
WARNING! Do not install the battery pack
before it has been completely assembled.
Always use gloves when handling the chain.
CHAIN AND GUIDE BAR ASSEMBLY
1. Unpack all parts carefully. Remove the chain cover
by turning the chain tensioning knob in a counter-
clockwise direction. (See Fig. A1)
2. Place the Chainsaw on a solid, level surface.
3. Use only genuine Kress chains or those
recommended for Guide Bar.
4. Slide the chain in the slot around the guide bar.
Ensure the chain is in correct running direction by
comparing it to the chain icon on the guide bar, or
referring to the chain direction symbol found on
the saw body. Ensure the bar tensioning plate is
facing outward. (See Fig. A2)
5. Fit the chain onto the drive sprocket, so that the
fastening bar bolt and the two bar locating tabs on
the bar pad t into the keyway of the opening on
the guide bar. (See Fig. B1, B2)
6. Assure all parts are seated properly and hold
chain and guide bar in a level position. Make sure
the drive links are fully seated in the drive sprocket
(See Fig. C1), avoiding a kink as shown in Fig. C2.
If kink occurs, pick up on the chain at the guide
bar just ahead of the kink and then pull the kink
out.
NOTE: Chain should rotate freely and be free of
kinks.
7. Fit the chain cover and tighten the chain cover by
turning the chain tensioning knob clockwise until it
is tight. (See Fig. D)
8. The chain will stretch while cutting and lose
proper tension. When the chain becomes loose,
completely unscrew the chain tensioning knob
or turn the knob around three (3) full turns in a
counter-clockwise direction, then retighten the
chain tensioning knob to properly reset the chain
tension by repeating Steps 6-7 listed above.
WARNING: The chain is not yet tensioned.
Tensioning the chain applies as described
under “TENSIONING CHAIN”. The chain
now needs to be inspected to make sure it is
properly tensioned.
TENSIONING CHAIN (See Fig. E1, E2)
NOTE: New saw chains will stretch. Check the chain
tension frequently when rst used and tighten when
the chain becomes loose around the guide bar.
WARNING:
●Removing the battery pack before adjusting saw
chain tension.
●Cutting edges on chain are sharp. Use protective
gloves when handling chain.
●Maintain proper chain tension always. A loose
chain will increase the risk of kickback. A loose
chain may jump out of guide bar groove. This may
injure operator and damage chain. A loose chain

15
EN
will cause chain, bar, and sprocket to wear rapidly.
1. Place the Chainsaw on any suitable at surface.
2. Turn the chain tensioning knob clockwise until it is
hand tight.
NOTE: The tension is automatically increased
while the chain tensioning knob is being turned
in a clockwise direction. The built-in ratchet
mechanism prevents the chain tension from
loosening.
3. Tilt the saw forward (See E1) where the guide bar
tip is pushed in an downward direction. This will
remove slack from the chain.
4. Fully tighten the chain tensioning knob by turning
it clockwise.
5. Double check the tension set by the automatic
chain tensioning knob. The correct chain tension
is reached when the chain can be raised approx.
Half the drivelink depth from the guide bar in the
center. This should be done by using one hand to
raise the chain against the weight of the machine.
(See Fig. E2)
NOTE: The chain is properly tensioned when it
can be lifted off of the Guide Bar and the drivelink
is within the rail of the Guide Bar.
NOTE: The chain will stretch while cutting and
lose proper tension. When the chain becomes
loose, completely unscrew the chain tensioning
knob or turn the knob around three full turns in
a counter-clockwise direction, then retighten the
chain tensioning knob to properly reset the chain
tension by repeating Steps 1-4 listed above.
LUBRICATION (See Fig. F)
IMPORTANT: The Chainsaw is not filled with
oil. It is essential to fill with oil before use.
Never operate the Chainsaw without chain
oil or at an empty oil tank level, as this will result in
extensive damage to the product.
NOTE: Chain life and cutting capacity depend
on optimum lubrication. Therefore, the chain is
automatically oiled during operation.
Filling oil tank:
WARNING: Removing the battery pack
before filling the oil tank.
1. Set Chainsaw on any suitable surface with oil ller
cap facing upward.
2. Clean area around the oil ller cap with cloth and
unscrew the cap by turning it counter clockwise.
3. Add bar and chain oil until tank is full.
4. Avoid dirt or debris entering oil tank, ret oil ller cap
and tighten by turning clockwise until hand tight.
IMPORTANT: To allow venting of the oil tank,
small breather channels are provided
between the oil filler cap and the strainer, to
prevent leakage, and ensure machine is left in a
horizontal position when not in use.
It is important to use bar and chain lubricant (not
provided) that is formulated to perform over a
wide temperature range with no dilution required.
This can be found at the location where you
purchased this saw or your local hardware store.
Do not use dirty, used or otherwise contaminated
oils. Damage may occur to the bar or chain.Use of
non approved oil will void the warranty.
Do not swallow. If swallowed, call a physician
immediately. Keep out of reach of children. Store
away from heat or open flame.
Checking the Automatic Oiler
Proper functioning of the automatic oiler can be
checked by running the Chainsaw and pointing the tip
of the guide chain bar towards a piece of cardboard
or paper on the ground. If an increasing oil pattern
develops on the cardboard, the automatic oiler is
operating ne. If there is no oil pattern, despite a full
oil reservoir, contact Kress customer service agent or
Kress approved service agent.
CAUTION: Do not touch the ground with the
chain. Ensure safety clearance of 40cm.
OPERATION
1. BEFORE USING YOUR CORDLESS TOOL
WARNING! The charger and battery pack are
specially designed to work together so do not
attempt to use any other devices. Never insert
or allow metallic objects into your charger or battery
pack connections because of an electrical failure and
hazard will occur.
NOTE: Your battery pack is UNCHARGED and you
must charge once before use.
The battery charger supplied is matched to the Li-ion
battery installed in the machine. Do not use another
battery charger.
2. CHECKING THE BATTERY CHARGE
CONDITION (See Fig. G)
The battery level can be known from the battery
indicator light by pressing the button beside the lights.
NOTE: Fig. G only applies for the battery pack with
battery indicator light.
3. CHARGING YOUR BATTERY PACK (See
Fig. H)
The Li-ion battery is protected against deep
discharging. When the battery is empty, the machine
is switched off by means of a protective circuit. Each
battery must be fully charged before the rst use.
In a warm environment or after heavy use, the battery
pack may become too hot to permit charging. Allow
time for the battery to cool down before recharging.
NOTE: Always fully charge the two batteries at
same time. More details can be found in charger’s
manual.
4. TO REMOVE OR INSTALL BATTERY PACK
(See Fig. I)
Depress the battery pack release button to remove
the 2 battery packs from your tool. After recharging,
insert the 2 battery packs into the battery ports. A

16
EN
simple push and slight pressure will be sufcient until
a click is heard. Check to see if the battery is fully
secured.
NOTE:
• When removing the battery pack, hold it firmly
to avoid dropping and injury.
• This machine will only run when 2 batteries are
installed. It is recommended to use the same
two batteries and charge the two batteries at
the same time.
• When you use two batteries with different
power, the machine will only run to the lower
common denominator.
5. POWER INDICATOR LIGHT (See Fig. J)
IMPORTANT:
When only one light is illuminated, your battery is
overly discharged, even though the machine may
still be capable to work. Continuing to operate
your machine with the battery in this discharged
condition may reduce the life and performance of
your battery.
When no light are illuminated, at least one battery
is not fully installed or battery may be defective,
please double check the batteries are fully seated
into position.
BATTERY STATUS
•Before starting or after use, press the button
beside the power indicator light on the machine to
check the battery capacity.
•During operation, the battery capacity will be
indicated automatically by the battery power
indicator. The indicator constantly senses and
displays the battery condition as follows.
•For the machine with 2 battery packs with
different power, the power indicator light displays
the battery condition with the lower one of the two
batteries.
Battery indicator
light status Battery condition
Five green lights
() are
illuminated.
The two batteries are in a
highly charged condition.
Two, three or four
green lights are
illuminated.
The two batteries have a
remaining charge. The more
lights are illuminated, the
more battery capacity.
Only one green
light ( )
is illuminated.
The battery level of at least
one battery pack is very low.
Please check and charge the
battery pack.
No light is
illuminated. At least one battery is not fully installed or battery may be
defective.
Only one light is
ashing twice per
cycle.
At least one battery is over
discharged (please refer to
the battery charge condition),
please recharge the two
batteries at once before use
again or storage.
Only one light
is ashing three
times per cycle.
At least one battery is hot,
wait for them cool down
before start again.
Only one light is
ashing four times
per cycle.
The machine is over load.
Remove tool from cutting
area and try again.
6. SWITCHING ON AND OFF (SEE FIG. K)
ATTENTION: Check the battery packs before
using your cordless tool. Only use the battery
pack listed in the accessories section.
For switching on the tool, press the lock-out button,
then fully press the on/off switch and hold in this
position. The lock-out button can now be released.
For switching off, release the on/off switch.
NOTE: The chain brake must be activated in order for
the saw to be switched on.
7. CHAIN BRAKE LEVER (See Fig. L)
The chain brake lever is a safety mechanism
activated through the front hand guard, when
kickback occurs. Chain stops immediately.
The following function check should be carried out
at regular intervals. Pull the front hand guard towards
the operator (position ) to deactivate chain brake.
To activate the chain brake, push front hand guard
forwards (position ).
NOTE: If the saw is unable to start, even though it is
assembled properly and working with fully charged
battery packs, then you should check if the chain
brake lever is in the correct position (position ).
8. CUTTING
IMPORTANT: Is the oil tank filled? Check
the Oil Level Window prior to starting and
regularly during operation (See Fig. M). Refill oil
when oil level is low. A full oil tank will last approx.
12 minutes of cutting depending on sawing
intensity and stops.
Check recent replaced chain tension about every
10 minutes during operation.
(1) Installing the battery pack into the machine.
(2) Make sure section of log to be cut is not laying on
the ground. This will keep the chain from touching
the ground as it cuts through the log.
Touching the ground while the chain is moving is
dangerous and will dull the chain.
(3) Use both hands to grip saw. Always use left hand
to grip front handle and right hand to grip rear
handle. Use a rm grip. Thumbs and ngers must
wrap around saw handles. (See Fig. N)
(4) Make sure your footing is rm. Keep feet-shoulder
width apart. Distribute your weight evenly on both

17
EN
feet.
(5) When ready to make a cut, push the lock-
out button completely in with the right thumb
and squeeze the trigger. This will turn saw on.
Releasing the trigger will turn the saw off. Make
sure the saw is running at full speed before starting
a cut.
(6) When starting a cut, slowly place moving chain
against the wood. The wood should be as close to
the saw body as possible. Hold saw rmly in place
to avoid possible bouncing or skating (sideways
movement) of saw.
(7) Guide the saw using light pressure and do not put
excessive force on the saw, letting the saw do its
work. The motor will overload and can burn out.
It will do the job better and safer at the rate for
which it was intended.
(8) Remove the saw from a cut with the saw running
at full speed. Stop the saw by releasing the on/off
switch. Make sure the chain has stopped before
setting the saw down.
(9) Keep practicing on scrap logs in a secure working
area until you are comfortable, using a uid motion
and a steady cutting rate.
Kickback Safety Devices On This Saw
This saw has a low-kickback chain and reduced
kickback Guide Bar. Both items reduce the chance
of kickback. However, kickback can still occur with
this saw.
The following steps will reduce the risk of kickback.
• Use both hands to grip saw while saw is running.
Use rm grip. Thumbs and ngers must wrap
around saw handles.
• Keep all safety items in place on saw. Make sure
they work properly.
• Do not overreach or cut above shoulder height.
• Keep solid footing and balance at all times.
• Stand slightly to the left side of saw. This keeps
your body from being in direct line with chain.
• Do not let Guide Bar nose touch anything when
chain is moving.
• Never try cutting through two logs at same time.
Only cut one log at a time.
• Do not bury the Guide Bar nose or try plunge cut
(boring into wood using guide bar nose).
• Watch for shifting of wood or other forces that
may pinch chain.
• Use extreme caution when reentering a previous
cut.
• Use only the low-kickback chain and guide
bar that were supplied with this Chainsaw or
recommended.
• Never use a dull or loose chain. Keep chain sharp
with proper tension.
How to use Saw Safely
1. Use the Chainsaw only with secure footing.
2. Hold the Chainsaw at the right-hand side of your
body (See Fig. O).
3. The chain must be running at full speed before it
makes contact with the wood.
4. Use the bumper spikes to secure the saw onto the
wood before starting to cut.
5. Use the Bumper Spikes as a leverage point while
cutting. (See Fig. P)
6. Do not operate the Chainsaw with arms fully
extended, attempt to saw areas which are difcult
to reach, or stand on a ladder while sawing (See
Fig. Q).
Never use the Chainsaw above shoulder height
Cutting wood under tension (See Fig. R)
WARNING: When cutting a limb that is
under tension, use extreme caution. Be alert
for wood springing back. When wood tension
is released, limb could spring back and strike
operator causing severe injury or death.
When sawing logs supported on both ends, start
the cut from above(Y) about 1/3 of the diameter into
the log (overbuck) and then nish the cut (Z) from
below, in order to avoid contact of the Chainsaw with
the ground. When sawing logs supported on only
one end, start the cut from below (Y) about 1/3 of
the diameter into the log (underbuck) and nish the
cut from above (Z) in order to avoid log splitting or
jamming of the Chainsaw.
SAW MAINTENANCE
Follow maintenance instructions in this manual.
Proper cleaning of saw and chain and Guide Bar
maintenance can reduce chances of kickback.
Inspect and maintain saw after each use. This will
increase the service life of your saw.
NOTE: Even with proper sharpening, risk of kickback
can increase with each sharpening.
MAINTENANCE AND
STORAGE OF CHAINSAW
1. Remove the battery pack
• When not in use
• Before moving from one place to another
• Before servicing
• Before changing accessories or attachments,
such as saw chain and guard
2. Inspect Chainsaw before and after each use.
Check saw closely if guard or other part has been
damaged. Check for any damage that may affect
operator safety or operation of saw. Check for
alignment or binding of moving parts. Check for
broken or damaged parts. Do not use Chainsaw if
damage affects safety or operation. Have damage
repaired by authorized service center.
3. Maintain Chainsaw with care.
• Never expose saw to rain or direct moisture.
• Keep chain sharp, clean, and lubricated for better
and safer performance.
• Follow steps outlined in this manual to sharpen
chain.
• Keep handles dry, clean, and free of oil and
grease.

18
EN
• Keep all screws and nuts tight.
4. When servicing, use only identical replacement
parts.
5. When not in use, always store Chainsaw
• in a high or locked place, out of children’s reach
• in a dry place
• with bar and chain cover in place
Bar Maintenance
To maximize bar life, the following bar maintenance is
recommended.
The bar rails that carry the chain should be cleaned
before storing the tool or if the bar or chain appear to
be dirty.
The rails should be cleaned every time the chain is
removed.
To clean the Bar rails:
1. Remove chain cover and bar and chain. (see
section ASSEMBLY)
2. Using a wire brush, screwdriver or similar tool,
clear the residue from the inner groove of the bar.
3. Make sure to clean oil passages thoroughly
Conditions which require chain and guide
bar maintenance:
• Saw cuts to one side or at an angle.
• Saw has to be forced through the cut.
• Inadequate supply of oil to the bar and chain.
Check the condition of the guide bar each time the
chain is sharpened. A worn guide bar will damage the
chain and make cutting difcult.
After each use, remove the battery pack, clean all
sawdust from the guide bar and sprocket hole.
When rail top is uneven, use a at le to restore
square edges and sides.
File Rail Edges
and Sides
Square
Worn Groove Correct Groove
Replace the guide bar when the groove is worn,
the guide bar is bent or cracked, or when excess
heating or burring of the rails occurs. If replacement
is necessary, use only the guide bar specied for your
saw in the repair parts list or on the decal located on
the Chainsaw.
Replacing Bar & Chain
Replace chain when cutters are too worn to sharpen
or when chain stops. Only use replacement chain
noted in this manual.
Inspect guide bar before sharpening chain. A worn
or damaged guide bar is unsafe. A worn or damaged
guide bar will damage chain. It will also make cutting
harder.
Fit the bar tensioning plate tab into the new bar by
tightening the screw clockwise. The tab protrusion (a)
must be tted into the bar hole. (See Fig. S)
SHARPENING SAW CHAIN
WARNING: Remove the battery pack before
servicing. Severe injury or death could
occur from electrical shock or body contact
with moving chain.
Cutting edges on chain are sharp. Use protective
gloves when handling chain.
Keep chain sharp. Your saw will cut faster and more
safely. A dull chain will cause undue sprocket, Guide
Bar, chain, and motor wear. If you must force chain
into wood and cutting creates only sawdust with few
large chips, chain is dull.
Lubricate Sprocket
WARNING: Wear heavy duty gloves when
performing any maintenance or service to
this tool. Always remove the battery pack
before performing any service or maintenance on
this tool.
NOTE: It is not necessary to remove the chain or bar
when lubricating the guide bar sprocket.
1. Clean the bar and sprocket
2. Using a grease gun, insert the tip of the gun
into the lubrication hole and inject grease until it
appears at the outside edge of the sprocket tip.
(See Fig. T)
3. To rotate the sprocket pull the chain by hand until
the ungreased side of the sprocket is in line with
the grease hole. Repeat the lubrication procedure.
FOR BATTERY TOOLS
The ambient temperature range for the use and
storage of tool and battery is 0 °C-45 °C
The recommended ambient te.mperature range for
the charging system during charging is 0 °C-40 °C.
ENVIRONMENTAL
PROTECTION
Waste electrical products must not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
local authorities or retailer for recycling advice.

19
EN
TROUBLESHOOTING TABLE
The following table gives checks and actions that
you can perform if your machine does not operate
correctly. If these do not identify/remedy the problem,
contact your service agent.
WARNING: Switch off and remove plug from
power source before investigating fault.
Symptom Possible Cause Remedy
Chainsaw fails
to
operate
Low battery
charge.
Chain brake not
in the proper
position.
Charge both
the battery
packs.
Check to
see if the
chain brake
is in position
. Refer
to CHAIN
BRAKE for
details.
Chainsaw
operates
intermittently
Over heating
Applying too
much pressure
while cutting.
Loose
connection.
Internal wiring
defective.
On/Off switch
defective.
Place the
machine
in a cool,
ventilated
place to cool
it down.
Applying
relatively less
pressure while
cutting.
Contact
service agent.
Contact
service agent.
Contact
service agent.
Dry chain No oil in
reservoir.
Vent in oil ller
cap clogged.
Oil passage
clogged.
Rell oil.
Clean cap.
Clean oil
passage
outlet.
Kickback
Brake/Run
Down Brake
Brake does not
stop chain Contact service agent
Chain/chain bar
over-heats. No oil in reservoir.
Vent in oil ller
cap clogged.
Oil passage
clogged.
Chain is over
tensioned.
Dull chain.
Rell oil.
Clean cap.
Clean oil
passage
outlet.
Adjust chain
tension.
Sharpen chain
or replace.
Chainsaw rips,
vibrates, does
not
saw properly.
Chain tension
too loose.
Dull chain.
Chain worn out.
Chain teeth are
facing in the
wrong direction.
Adjust chain
tension.
Sharpen chain
or replace.
Replace
chain.
Reassemble
with chain
in correct
direction.
DECLARATION OF
CONFORMITY
We,
Positec Germany GmbH
Postfach 32 02 16, 50796 Cologne, Germany
Declare that the product
Description Battery-powered chainsaw
Type KG347E KG347E.X (3 - designation of
machinery, representative of Chainsaw)
Function Cutting wood
Complies with the following Directives:
2006/42/EC, 2014/30/EU
2011/65/EU&(EU)2015/863
2000/14/EC amended by 2005/88/EC
The notied body involved
Name: Intertek Deutschland GmbH (Notified body
0905)
Address: Stangenstraße 1, 70771 LEINFELDEN-
ECHTERDINGEN
Certification No.: 20SHW2092-02
2000/14/EC amended by 2005/88/EC:
- Conformity Assessment Procedure as per Annex V
- Measured Sound Power Level 101.2 dB(A)
- Declared Guaranteed Sound Power Level 104 dB(A)
Standards conform to
EN 62841-1, EN 62841-4-1, EN ISO 3744,
EN 55014-1, EN 55014-2
The person authorized to compile the technical le,
Name: Marcel Filz
Address: Positec Germany GmbH
Postfach 32 02 16, 50796 Cologne, Germany
2021/10/28
Allen Ding
Deputy Chief Engineer, Testing & Certication
Positec Technology (China) Co., Ltd.
18, Dongwang Road, Suzhou Industrial
Park, Jiangsu 215123, P. R. China

20
D
INHALTSVERZEICHNIS
Einführung......................................................................................................................................................20
Sicherheitshinweise...................................................................................................................................21
Komponenten..............................................................................................................................................27
Spezikationen............................................................................................................................................27
Montage ........................................................................................................................................................28
Bedienung.....................................................................................................................................................30
Wartung..........................................................................................................................................................32
Umweltschutz..............................................................................................................................................33
Problemlösung.............................................................................................................................................34
Konformitätserklärung..............................................................................................................................34
EINFÜHRUNG
Sehr geehrter Kunde,
Vielen Dank, dass Sie dieses Kress-Produkt gekauft haben. Wir sind bestrebt, quali-
tativ hochwertige Produkte zu entwickeln, um Ihren Anforderungen im Bereich Rasen
und Garten gerecht zu werden.
Die Marke Kress steht für erstklassigen Service. Wenn Sie im Laufe der Jahre
Fragen oder Bedenken zu Ihrem Produkt haben, wenden Sie sich bitte an Ihren
Einkaufsstandort oder an unseren Kundenservice.
Wir sind zuversichtlich, dass Sie in den kommenden Jahren die Arbeit mit Ihrem
Kress-Produkt genießen werden.
BESTIMMUNGSGEMÄSSER GEBRAUCH
Die Kettensäge ist für das Sägen von Bäumen bestimmt, Baumstämme, Äste,
Balken, Bohlen, etc. Cuts kann mit oder quer zur Faser gesägt werden. Dieses
Produkt eignet sich nicht für das Sägen von mineralischen Stoffen.