KRESS KG367.X User manual

Cordless Chainsaw EN P02
Tronçonneuse sans l F P21
Sierra de cadena inalámbrica ES P38
KG367 KG367.X

2
EN
TABLE OF CONTENTS
Introduction.........................................................................................................................................................2
Safety Instructions.............................................................................................................................................3
Symbols..............................................................................................................................................................8
Specications.....................................................................................................................................................9
Component List................................................................................................................................................11
Assembly..........................................................................................................................................................16
Operation..........................................................................................................................................................17
Maintenance.....................................................................................................................................................18
Troubleshooting................................................................................................................................................20
INTRODUCTION
Dear Customer,
Thank you for buying this Kress product. We are dedicated to developing high quality products to
meet your lawn & garden requirements.
The Kress brand is synonymous with premium quality service. Over the years of your products life, if
you have any questions or concerns about your product, please contact your location of purchase or
our Customer Service Team for assistance.
We are condent you will enjoy working with your Kress product for years to come.
INTENDED USE OF CHAINSAW
This Chainsaw is designed for felling trees, limbing, bucking tree trunks, cutting wooden beams, etc. All
cuts should be across the grain. This product is intended for cutting wood only.

3
EN
PRODUCT SAFETY
WARNING: Some dust created by power
sanding, sawing, grinding, drilling and
other construction activities contains chemicals
known to the State of California to cause cancer,
birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints;
• Crystalline silica from bricks and cement and
other masonry products;
• Arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a
well ventilated area, and work with approved
safety equipment, such as those dust masks that
are specially designed to filter out microscopic
particles.
WARNING: This product can expose you to
chemicals including lead and Di(2-ethylhexyl)
phthalate (DEHP) which are known to the State
of California to cause cancer and birth defects or
other reproductive harm. For more information go
to www.P65Warnings.ca.gov.
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING Read all safety warnings,
instructions, illustrations and specifications
provided with this power tool. Failure to follow all
instructions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1. WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2. ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp loca-
tion is unavoidable, use a residual current
device (RCD) protected supply . Use of an RCD
reduces the risk of electric shock.
3. PERSONAL SAFETY
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medi-
cation. A moment of inattention while operating
power tools may result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing
protection used for appropriate conditions will
reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising power
tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from
moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dust-
related hazards.
h) Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action
can cause severe injury within a fraction of a
second.
4. POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the

4
EN
rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow
for safe handling and control of the tool in
unexpected situations.
5. BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified by
the manufacturer . A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from
one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery
may cause irritation or burns.
e) Do not use a battery pack or tool that is
damaged or modified. Damaged or modified
batteries may exhibit unpredictable behaviour
resulting in fire, explosion or risk of injury.
f) Do not expose a battery pack or tool to fire
or excessive temperature. Exposure to fire or
temperature above 130 °C may cause explosion.
g) Follow all charging instructions and do not
charge the battery pack or tool outside
the temperature range specified in the
instructions. Charging improperly or at
temperatures outside the specified range may
damage the battery and increase the risk of fire.
6. SERVICE
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
b) Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
1) GENERAL CHAIN SAW
SAFETY WARNINGS:
a) Keep all parts of the body away from the saw
chain when the chain saw is operating. Before
you start the chain saw, make sure the saw
chain is not contacting anything. A moment of
inattention while operating chain saws may cause
entanglement of your clothing or body with the
saw chain.
b) Always hold the chain saw with your right
hand on the rear handle and your left hand on
the front handle. Holding the chain saw with a
reversed hand configuration increases the risk of
personal injury and should never be done.
c) Hold the chain saw by insulated gripping
surfaces only, because the saw chain may
contact hidden wiring . Saw chains contacting a
“live”wire may make exposed metal parts of the
chain saw “live”and could give the operator an
electric shock.
d) Wear safety glasses protection. Further
protective equipment for hearing, head,
hands, legs and feet is recommended.
Adequate protective clothing will reduce personal
injury by flying debris or accidental contact with
the saw chain.
e) Do not operate a chain saw, on a ladder, from
a rooftop, or any unstable support. Operation
of a chain saw in this manner could result in
serious personal injury.
f) Always keep proper footing and operate
the chain saw only when standing on fixed,
secure and level surface. Slippery or unstable
surfaces may cause a loss of balance or control of
the chain saw.
g) When cutting a limb that is under tension , be
alert for spring back. When the tension in the
wood fibres is released , the spring loaded limb
may strike the operator and/or throw the chain
saw out of control.
h) Use extreme caution when cutting brush and
saplings. The slender material may catch the saw
chain and be whipped toward you or pull you off
balance.
i) Carry the chain saw by the front handle with

5
EN
the chain saw switched off and away from
your body. When transporting or storing the
chain saw , always fit the guide bar cover.
Proper handling of the chain saw will reduce the
likelihood of accidental contact with the moving
saw chain.
j) Follow instructions for lubricating,
chain tensioning and changing the bar
and chain. Improperly tensioned or
lubricated chain may either break or
increase the chance for kickback.
k) Cut wood only. Do not use chain saw for
purposes not intended. For example: do
not use chain saw for cutting metal, plastic,
masonry or non-wood building materials . Use
of the chain saw for operations different than
intended could result in a hazardous situation.
l) Do not attempt to fell a tree until you have an
understanding of the risks and how to avoid
them. Serious injury could occur to the operator
or bystanders while felling a tree.
m) Do not operate a chain saw in a tree unless
you have been specifically trained to do so.
Operation of a chain saw in a tree without
proper training could increase the risk of
serious personal injury.
n) Follow all instructions when clearing
jammed material, storing or servicing
the chain saw. Make sure the switch
is off and the battery pack is removed.
Unexpected actuation of the chain saw while
clearing jammed material or servicing may result
in serious personal injury.
o) Recommendation that the first-time user
should, as a minimum, practice cutting logs
on a saw-horse or cradle.
p) Recommendation to have sharpening and
maintenance of the saw chain performed by
authorised service centers.
2) CAUSES AND OPERATOR
PREVENTION OF KICKBACK :
Kickback may occur when the nose or tip of the
guide bar touches an object, or when the wood
closes in and pinches the saw chain in the cut.
Tip contact in some cases may cause a sudden
reverse reaction, kicking the guide bar up and
back towards the operator. Pinching the saw chain
along the top of the guide bar may push the guide
bar rapidly back towards the operator.
Either of these reactions may cause you to lose
control of the saw which could result in serious
personal injury.
Do not rely exclusively upon the safety devices
built into your saw. As a chain saw user, you
should take several steps to keep your cutting jobs
free from accident or injury.
Kickback is the result of chain saw misuse and/or
incorrect operating procedures or conditions and
can be avoided by taking proper precautions as
given below:
a) Maintain a firm grip, with thumbs and fingers
encircling the chain saw handles, with both
hands on the saw and position your body
and arm to allow you to resist kickback
forces. Kickback forces can be controlled by the
operator, if proper precautions are taken. Do not
let go of the chain saw.
b) Do not overreach and do not cut above
shoulder height. This helps prevent unintended
tip contact and enables better control of the chain
saw in unexpected situations.
c) Only use replacement bars and chains
specified by the manufacturer. Incorrect
replacement guide bars and saw chains may
cause chain breakage and/or kickback.
d) Follow the manufacturer’s sharpening and
maintenance instructions for the saw chain.
Decreasing the depth gauge height can lead to
increased kickback.
SAFETY WARNINGS FOR
BATTERY PACK
a) Do not dismantle, open or shred battery pack.
b) Do not expose battery pack to heat or fire.
Avoid storage in direct sunlight.
c) Do not short-circuit a battery pack. Do not
store battery packs haphazardly in a box or
drawer where they may short-circuit each other
or be short-circuited by other metal objects.
When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or fire.
d) Do not subject battery pack to mechanical
shock.
e) In the event of battery leaking, do not allow the
liquid to come in contact with the skin or eyes.
If contact has been made, wash the affected
area with copious amounts of water and seek
medical advice.
f) Do not use any battery pack which is not
designed for use with the equipment.
g) Keep battery pack out of the reach of children.
h) Always purchase the battery pack
recommended by the device manufacturer for
the equipment.
i) Keep battery pack clean and dry.
j) Wipe the battery pack terminals with a clean
dry cloth if they become dirty.
k) Battery pack needs to be charged before use.
Always use the correct charger and refer to
the manufacturer’s instructions or equipment
manual for proper charging instructions.
l) Do not leave battery pack on prolonged charge
when not in use.
m) After extended periods of storage, it may

6
EN
be necessary to charge and discharge the
battery pack several times to obtain maximum
performance.
n) Recharge only with the charger specified by
Kress. Do not use any charger other than
that specifically provided for use with the
equipment.
o) Retain the original product literature for future
reference.
p) Use only the battery pack in the application for
which it was intended.
q) Remove the battery pack from the equipment
when not in use.
r) Dispose of properly.
s) Do not mix cells of different manufacture,
capacity, size or type within a device.
t) Keep the battery away from microwaves and
high pressure.
SAVE THESE INSTRUCTIONS
Instructions concerning the proper techniques
for basic felling, limbing, and cross-cutting
(bucking)
1. Felling a tree
When bucking and felling operations are being
performed by two or more persons at the same
time, the felling operations should be separated
from the bucking operation by a distance of at
least twice the height of the tree being felled. Trees
should not be felled in a manner that would
endanger any person, strike any utility line or cause
any property damage. If the tree does make
contact with any utility line, the company should be
notied immediately.
The Chainsaw operator should keep on the uphill
side of the terrain as the tree is likely to roll or slide
downhill after it is felled.
An escape path should be planned and cleared as
necessary before cuts are started. The escape
path should extend back and diagonally to the rear
of the expected line of fall as illustrated in Figure 1.
Before felling is started, consider the natural lean
of the tree, the location of larger branches and the
wind direction to judge which way the tree will fall.
Remove dirt, stones, loose bark, nails, staples and
wire from the tree.
2. Notching undercut
Make the notch 1/3 the diameter of the tree,
perpendicular to the direction of falls as illustrated
in Figure 1. Make the lower horizontal notching
cut (W) rst. This will help to avoid pinching either
the saw chain or the guide bar when the second
notch (X) is being made.
3. Felling back cut
Make the felling back cut (Y) at least 50 mm higher
than the horizontal notching cut as illustrated in
Figure 1.
Keep the felling back cut parallel to the horizontal
notching cut.
Make the felling back cut so enough wood is left
to act as a hinge. The hinge wood keeps the tree
from twisting and falling in the wrong direction. Do
not cut through the hinge.
As the felling gets close to the hinge, the tree
should begin to fall. If there is any chance that the
tree may not fall in desired direction or it may rock
back and bind the saw chain, stop cutting before
the felling back cut is complete and use wedges of
wood, plastic or aluminium (Z) to open the cut and
drop the tree along the desired line of fall ( ).
When the tree begins to fall remove the Chainsaw
from the cut, stop the motor, put the Chainsaw
down, then use the retreat path planned ( ). Be
alert for overhead limbs falling and watch your
footing. (See Figure 1)
3
22
W
YZ
X
50mm
50mm
1
1
1
2
2/3
1
1/3
12
2/3
1/3
Fig.1
Fig.2
Fig.3
Fig.4
Fig.5
Fig.6
4. Limbing a tree
Limbing is removing the branches from a fallen
tree.
When limbing leave larger lower limbs to support
the log off the ground. Remove the small limbs in
one cut as illustrated in Figure 2. Branches under
tension should be cut from the bottom up to avoid
binding the Chainsaw.
3
22
W
YZ
X
50mm
50mm
1
1
1
2
2/3
1
1/3
12
2/3
1/3
Fig.1
Fig.2
Fig.3
Fig.4
Fig.5
Fig.6
5. Bucking a log
Bucking is cutting a log into lengths. It is important
to make sure your footing is rm and your weight
is evenly distributed on both feet. When possible,
the log should be raised and supported by the use
of limbs, logs or chocks. Follow the simple
directions for easy cutting.
When the log is supported along its entire length
as illustrated in Figure 3, it is cut from the top
(overbuck), avoid contacting ground as this will
greatly reduce the chain sharpness.

7
EN
3
22
W
YZ
X
50mm
50mm
1
1
1
2
2/3
1
1/3
12
2/3
1/3
Fig.1
Fig.2
Fig.3
Fig.4
Fig.5
Fig.6
When the log is supported on one end, as
illustrated in Figure 4, cut 1/3 the diameter from
the underside (underbuck) (1). Then make the
nished cut by overbucking (2) to meet the rst
cut.
3
22
W
YZ
X
50mm
50mm
1
1
1
2
2/3
1
1/3
12
2/3
1/3
Fig.1
Fig.2
Fig.3
Fig.4
Fig.5
Fig.6
When the log is supported on both ends, as
illustrated in Figure 5, cut 1/3 the diameter from the
top (overbuck) (1). Then make the nished cut by
underbucking (2) the lower 2/3 to meet the rst cut.
3
22
W
YZ
X
50mm
50mm
1
1
1
2
2/3
1
1/3
12
2/3
1/3
Fig.1
Fig.2
Fig.3
Fig.4
Fig.5
Fig.6
When bucking on a slope always stand on the
uphill side of the log, as illustrated in Figure 6.
When “cutting through”, to maintain complete
control release the cutting pressure near the end of
the cut without relaxing your grip on the Chainsaw
handles. Don’t let the chain contact the ground.
After completing the cut, wait for the saw chain to
stop before you move the Chainsaw.
Always stop the motor before moving from tree to
tree.
3
22
W
YZ
X
50mm
50mm
1
1
1
2
2/3
1
1/3
12
2/3
1/3
Fig.1
Fig.2
Fig.3
Fig.4
Fig.5
Fig.6

8
EN
SYMBOLS
To reduce the risk of injury, user
must read instruction manual
WARNING
Wear ear protection
Wear eye protection
Wear dust mask
Always use chain saw two-handed
(left hand must be on top handle,
right hand must be on rear handle)
Beware of chain saw kickback and
avoid contact with bar tip
Do not expose to rain
Wear head protection
Wear protective gloves
Li-Ion battery, battery must be
recycled
Do not burn
Batteries may enter water cycle if
disposed improperly, which can be
hazardous for ecosystem. Do not
dispose of waste batteries as
unsorted municipal waste.
Unlock
Lock
Positec Inc. has established a partnership with
the RBRC Corporation to recycle any Positec
batteries with the RBRC-call2recycle seal. For
environmental protection, please do not discard
batteries in the trash.
After the batteries' life cycle is ended, then
please call 1-800-822-8837 for a free service that
will properly dispose of the battery.

9
EN
TECHNICAL DATA
Type Designation KG367 KG367.X (3 - designation of machinery, representative of Chainsaw)
KG367 KG367.X *
Rated voltage 60 V Max. **
Bar length 16'' (40 cm)
Chain speed 72 ft/s (22 m/s)
Oil tank capacity 6.7 oz. (190 ml)
Chain pitch 3/8'' LP (0.95 cm)
Chain gauge 0.043'' (1.1 mm)
Machine weight (bare tool) 9.5 lbs (4.3 kg)
* X may be followed by one or two characters. All models are the same except model number and
trademark. The suffix in models may be number from “1” to “999” or English letter “A” to “Z” or “M1” to”
M9” which means different package or the various of accessories packed in the package.
** Voltage measured without workload. Initial battery voltage reaches maximum of 60 volts. Nominal voltage
is 54 volts.
Category Type Capacity
60V Battery KA3001 2.5 Ah
KA3008 5.0 Ah
60V Charger KA3712 3.0 A
KA3714 5.0 A
We recommend that you purchase your accessories from the same location in all places that sold you the
tool. Refer to the accessory packaging for further details. Store personnel can assist you and offer advice.

10
EN
12
34
567
8
9
13 11 10
12
14
22
21
17
15 1918
20
16

11
EN
COMPONENT LIST
1. CHAIN
2. GUIDE BAR
3. CHAIN BRAKE LEVER (HAND GUARD)
4. FRONT HANDLE
5. BATTERY PACK RELEASE BUTTON
6. THROTTLE LOCK-OUT BUTTON
7. REAR HANDLE
8. REAR HAND GUARD
9. THROTTLE TRIGGER
10. BATTERY PACK ***
11. OIL LEVEL WINDOW
12. OIL FILLER CAP
13. BUMPER SPIKE
14. CHAIN COVER
15. CHAIN TENSIONING KNOB
16. CHAIN DIRECTION SYMBOL
17. OIL OUTLET
18. BAR LOCATING TABS
19. FASTENING BAR BOLT
20. BAR PAD
21. DRIVE SPROCKET
22. PROTECTIVE SCABBARD
23. BAR TENSIONING PLATE (SEE FIG. A2)
*** Not all the accessories illustrated or described are included in standard delivery.

2
B1 B2
C
A1
23
A2
1
Kink/Plis/Torcimiento
D

3-5mm
EN:Bar / F: Bar
ES: Barra de guía
0.12-0.2”
H
G
E
I1
100%
0%
F
1
2
I2

1
21
2
Click/
Cliquez/Clic Click/ Cliquez/Clic
KL
J1 J2
M
1
2
1
2
N

O
S
Q
2
2
1
1
R
P
EN: Injecting grease to lubricate
ES: Inyectando grasa para lubricar
F: Injectez la graisse pour lubrifier
T

16
EN
ASSEMBLY
WARNING! Do not install the battery pack
before it has been completely assembled.
Always use gloves when handling the chain.
CHAIN AND GUIDE BAR ASSEMBLY
1. Unpack all parts carefully. Remove the chain cover
by turning the chain tensioning knob in a
counterclockwise direction. (See Fig. A1)
2. Place the Chainsaw on a solid, level surface.
3. Use only genuine Kress chains or those
recommended for Guide Bar.
4. Slide the chain in the slot around the guide bar.
Ensure the chain is in correct running direction by
comparing it to the chain icon on the guide bar, or
referring to the chain direction symbol found on
the saw body. Ensure the bar tensioning plate is
facing outward. (See Fig. A2)
5. Fit the chain onto the drive sprocket, so that the
two bar locating tabs on the bar pad t into the
keyway of the opening on the guide bar. (See Fig.
B1, B2)
6. Assure all parts are seated properly and hold
chain and guide bar in a level position. Make sure
the drive links are fully seated in the drive sprocket
(See Fig. C), avoiding a kink as shown in Fig. D. If
kink occurs, pick up on the chain at the guide bar
just ahead of the kink and then pull the kink out.
NOTE: Chain should rotate freely and be free of
kinks.
7. Fit the chain cover and tighten the chain cover by
turning the chain tensioning knob clockwise until it
is slightly tight.(See Fig. E)
WARNING: The chain is not yet tensioned.
Tensioning the chain applies as described
under “TENSIONING CHAIN”. The chain
now needs to be inspected to make sure it is
properly tensioned.
TENSIONING CHAIN (See Fig. E, F)
NOTE: New saw chains will stretch. Check the chain
tension frequently when rst used and tighten when
the chain becomes loose around the guide bar.
WARNING:
●Removing the battery pack before adjusting saw
chain tension.
●Cutting edges on chain are sharp. Use protective
gloves when handling chain.
●Maintain proper chain tension always. A loose
chain will increase the risk of kickback. A loose
chain may jump out of guide bar groove. This may
injure operator and damage chain. A loose chain
will cause chain, bar, and sprocket to wear rapidly.
1. Place the Chainsaw on any suitable at surface.
2. Turn the chain tensioning knob clockwise until it is
hand tight.
3. Tilt the saw forward where the guide bar makes
contact with your working surface and pushed the
tip in an upward direction. This will remove slack
from the chain. Fully tighten the chain tensioning
knob by turning it clockwise.
NOTE: The tension is automatically increased
while the chain tensioning knob is being turned
in a clockwise direction. The built-in ratchet
mechanism prevents the chain tension from
loosening.
4. Double check the tension set by the automatic
chain tensioning knob. The correct chain tension
is reached when the chain can be raised approx.
Half the drivelink depth from the guide bar in the
center. This should be done by using one hand to
raise the chain against the weight of the machine.
(See Fig. F, G)
NOTE: The chain is properly tensioned when it
can be lifted off of the Guide Bar and the drivelink
is within the rail of the Guide Bar.
NOTE: The chain will stretch while cutting and
lose proper tension. When the chain becomes
loose, completely unscrew the chain tensioning
knob or turn the knob around three full turns in
a counter-clockwise direction, then retighten the
chain tensioning knob to properly reset the chain
tension by repeating Steps 1-4 listed above.
LUBRICATION (See Fig. H)
IMPORTANT: The Chainsaw is not filled with
oil. It is essential to fill with oil before use.
Never operate the Chainsaw without bar
and chain oil or allow the tank to become empty,
as this will result in extensive damage to the
product.
NOTE: Chain life and cutting capacity depend
on optimum lubrication. Therefore, the chain is
automatically oiled during operation.
FILLING OIL TANK:
WARNING: Removing the battery pack
before filling the oil tank.
1. Set Chainsaw on any suitable surface with oil ller
cap facing upward.
2. Clean area around the oil ller cap with cloth and
unscrew the cap by turning it counter clockwise.
3. Add bar and chain oil until tank is full.
4. Avoid dirt or debris entering oil tank, ret oil ller cap
and tighten by turning clockwise until hand tight.
IMPORTANT: To allow venting of the oil tank,
small breather channels are provided
between the oil filler cap and the strainer, to
prevent leakage, ensure machine is left in a
horizontal position when not in use.
It is important to use bar and chain lubricant (not
automotive oil) that is formulated to perform
over a wide temperature range with no dilution
required. This can be found at the location where
you purchased this saw or your local hardware
store. Do not use dirty, used or otherwise
contaminated oils. Damage may occur to the
bar or chain.Use of non approved oil will void the
warranty.

17
EN
Do not swallow any type of bar oil. If swallowed,
call a physician immediately. Keep out of reach of
children. Store away from heat or open flame.
CHECKING THE AUTOMATIC OILER
Proper functioning of the automatic oiler can be
checked by running the Chainsaw and pointing the tip
of the guide chain bar towards a piece of cardboard
or paper on the ground. If an increasing oil pattern
develops on the cardboard, the automatic oiler is
operating ne. If there is no oil pattern, despite a full
oil reservoir, contact Kress customer service agent or
Kress approved service agent.
NOTE: It make take an extended period of time (1
minute +) for the pump to prime when new or after
the saw has not been in use for an extended period
of time.
CAUTION: Do not touch the ground with the
chain. Ensure safety clearance of 6'' (15
cm).
OPERATION
BEFORE USING YOUR CORDLESS TOOL
WARNING! The charger and battery pack
are specially designed to work together so
do not attempt to use any other devices. Never
insert or allow metallic objects into your charger
or battery pack connections because of an
electrical failure and hazard will occur.
NOTE: Your battery pack is UNCHARGED and you
must charge once before use.
The battery charger supplied is matched to the Li-ion
battery installed in the machine. Do not use another
battery charger.
CHECKING THE BATTERY CHARGE
CONDITION (See Fig. I1)
Before starting or after use, press the button beside
the power indicator light on the battery pack to check
the battery capacity.
NOTE: Fig. I1 only applies for the battery pack with
battery indicator light.
Remarks LED-light Battery condition
Five green
lights are
illuminated.
70% ≤ Power level≤100%
Four green
lights are
illuminated.
50% ≤ Power level < 69%
Three
green
lights are
illuminated.
35% ≤ Power level < 49%
Two green
lights are
illuminated.
20% ≤ Power level < 34%
One green
light are
illuminated.
10% ≤ Power level < 19%
No light is
illuminated.
Power level < 10%
CHARGING YOUR BATTERY PACK (See Fig.
I2)
The Li-ion battery is protected against deep
discharging. When the battery is empty, the machine
is switched off by means of a protective circuit. Each
battery must be fully charged before the rst use.
In a warm environment or after heavy use, the battery
pack may become too hot to permit charging. Allow
time for the battery to cool down before recharging.
TO REMOVE OR INSTALL BATTERY PACK
(See Fig. J1, J2)
Depress the battery pack release button to remove
the battery pack from your tool. After recharging,
insert the battery pack into the battery port. A simple
push and slight pressure will be sufcient until a click
is heard. Check to see if the battery is fully secured.
NOTE: When removing the battery pack, hold it
firmly to avoid dropping and injury.
SWITCHING ON AND OFF (SEE FIG. K)
ATTENTION: Check the battery packs before using
your cordless tool. Only use the battery pack listed
in the accessories section.
For switching on the tool, press the throttle lock-out
button, then fully press the throttle trigger and hold
in this position. The throttle lock-out button can now
be released. If the saw does not function, please see
CHAIN BRAKE LEVER information below.
For switching off, release the throttle trigger.
NOTE: The chain brake must be activated in order for
the saw to be switched on.
CHAIN BRAKE LEVER (See Fig. L)
The chain brake lever is a safety mechanism activated
through the front hand guard, when kickback occurs.
Chain stops immediately.
The following function check should be carried out
at regular intervals. Pull the front hand guard towards
the operator (position ) to deactivate chain brake.
To activate the chain brake, push front hand guard
forwards (position ).

18
EN
NOTE: If the saw is unable to start, even though it is
assembled properly and working with fully charged
battery packs, then you should check if the chain
brake lever is in the correct position (position ).
CUTTING
IMPORTANT: Is the oil tank filled? Check
the Oil Level Window prior to starting and
regularly during operation (See Fig. M). Refill oil
when oil level is low. A full oil tank will last approx.
12 minutes of cutting depending on sawing
intensity and stops.
Check recent replaced chain tension about every
10 minutes during operation.
(1) Installing the battery pack into the machine.
(2) Make sure section of log to be cut is not laying
on the ground. if the log you are cutting is laying
on the ground, do not cut completely through
and allow the chain to make contact with the soil.
Reposition the log for the nal separating cut.
(3) Use both hands to grip saw. Always use left hand
to grip front handle and right hand to grip rear
handle. Use a rm grip. Thumbs and ngers must
wrap around saw handles. (See Fig. N)
(4) Make sure your footing is rm. Keep feet-shoulder
width apart. Distribute your weight evenly on both
feet.
(5) When ready to make a cut, push the throttle
lock-out button completely in with the right thumb
and squeeze the trigger. This will turn saw on.
Releasing the trigger will turn the saw off. Make
sure the saw is running at full speed before starting
a cut.
(6) When starting a cut, slowly place moving chain
against the wood. The wood should be as close to
the saw body as possible. Hold saw rmly in place
to avoid possible bouncing or skating (sideways
movement) of the saw.
(7) Guide the saw using light pressure with your left
forearm and do not put excessive force on the
saw, letting the saw do its work. The motor will
overload and can burn out. It will do the job better
and safer at the rate for which it was intended.
(8) Remove the saw from a cut with the saw running
at full speed. Stop the saw by releasing the throttle
trigger. Make sure the chain has stopped before
setting the saw down.
(9) Keep practicing on scrap logs in a secure working
area until you are comfortable, using a uid motion
and a steady cutting rate.
KICKBACK SAFETY DEVICES ON THIS SAW
This saw has a low-kickback chain and reduced
kickback Guide Bar. Both items reduce the chance
of kickback. However, kickback can still occur with
this saw.
The following steps will reduce the risk of kickback.
• Use both hands to grip saw while saw is running.
Use rm grip. Thumbs and ngers must wrap
around saw handles.
• Keep all safety items in place on saw. Make sure
they work properly.
• Do not overreach or cut above shoulder height.
• Keep solid footing and balance at all times.
• Stand slightly to the left side of saw. This keeps
your body from being in direct line with chain.
• Do not let Guide Bar nose tip touch anything when
chain is moving.
• Never try cutting through two logs at same time.
Only cut one log at a time.
• Do not bury the Guide Bar nose or try plunge cut
(boring into wood using guide bar nose). This type
of cutting is for properly trained professionals only.
• Watch for shifting of wood or other forces that
may pinch chain.
• Use extreme caution when reentering a previous
cut.
• Use only the low-kickback chain and guide bar
that were supplied with this Chainsaw or or are
recommended as a replacement.
• Never use a dull or loose chain. Keep chain sharp
with proper tension.
HOW TO USE SAW SAFELY
1. Use the Chainsaw only with secure footing.
2. Hold the Chainsaw at the right-hand side of your
body (See Fig. O).
3. The chain must be running at full speed before it
makes contact with the wood.
4. Use the bumper spikes to secure the saw onto the
wood when starting to cut.
5. Use the Bumper Spikes as a leverage point while
cutting if necessary. (See Fig. P)
6. Do not operate the Chainsaw with arms fully
extended, attempt to saw areas which are difcult
to reach, or stand on a ladder while sawing (See
Fig. Q).
Never use the Chainsaw above shoulder height.
CUTTING WOOD UNDER TENSION (SEE
FIG. R)
WARNING: When cutting a limb that is
under tension, use extreme caution. Be alert
for wood springing back. When wood tension
is released, limb could spring back and strike
operator causing severe injury or death.
When sawing logs supported on both ends, start
the cut from above(1) about 1/3 of the diameter into
the log (overbuck) and then nish the cut (2) from
below, in order to avoid contact of the Chainsaw with
the ground. When sawing logs supported on only
one end, start the cut from below (1) about 1/3 of
the diameter into the log (underbuck) and nish the
cut from above (2) in order to avoid log splitting or
jamming of the Chainsaw.
When cutting short sections (example of rewood), it
is not normally necessary to perform the underbuck
cut when the log is supported on one end.
SAW MAINTENANCE
Follow maintenance instructions in this manual.
Proper cleaning of saw and chain and Guide Bar

19
EN
maintenance can reduce chances of kickback.
Inspect and maintain saw after each use. This will
increase the service life of your saw.
NOTE: Even with proper sharpening, risk of kickback
can increase with each sharpening.
MAINTENANCE AND
STORAGE OF CHAINSAW
1. Remove the battery pack
• When not in use
• Before moving from one place to another
• Before servicing
• Before changing accessories or attachments,
such as saw chain and guard
2. Inspect Chainsaw before and after each use.
Check saw closely if guard or other part has been
damaged. Check for any damage that may affect
operator safety or operation of saw. Check for
alignment or binding of moving parts. Check for
broken or damaged parts. Do not use Chainsaw if
damage affects safety or operation. Have damage
repaired by authorized service center.
3. Maintain Chainsaw with care.
• Never expose saw to rain or direct moisture.
• Keep chain sharp, clean, and lubricated for better
and safer performance.
• Follow steps outlined in this manual to sharpen
chain.
• Keep handles dry, clean, and free of oil and
grease.
• Keep all screws and nuts tight.
4. When servicing, use only identical replacement
parts.
5. When not in use, always store Chainsaw
• in a high or locked place, out of children’s reach
• in a dry place
• with protective scabbard in place
BAR MAINTENANCE
To maximize bar life, the following bar maintenance is
recommended.
The bar rails that carry the chain should be cleaned
before storing the tool or if the bar or chain appear to
be dirty.
The rails should be cleaned every time the chain is
removed.
TO CLEAN THE BAR RAILS:
1. Remove drive cover and bar and chain. (see
section ASSEMBLY)
2. Using a wire brush, screwdriver or similar tool,
clear the residue from the inner groove of the bar.
(See Fig. S)
3. Make sure to clean oil passages thoroughly.
CONDITIONS WHICH REQUIRE CHAIN AND
GUIDE BAR MAINTENANCE:
• Saw cuts to one side or at an angle.
• Saw has to be forced through the cut.
• Inadequate supply of oil to the bar and chain.
Check the condition of the guide bar each time the
chain is sharpened. A worn guide bar will damage the
chain and make cutting difcult.
After each use, remove the battery pack, clean all
sawdust from the guide bar and sprocket hole.
When rail top is uneven, use a at le to restore
square edges by removing any burrs from the side or
top of the bar.
File Rail Edges
and Sides
Square
Worn Groove Correct Groove
Replace the guide bar when the groove is worn,
the guide bar is bent or cracked, or when excess
heating or burring of the rails occurs. If replacement
is necessary, use only the guide bar specied for your
saw in the repair parts list or on the decal located on
the Chainsaw.
REPLACING BAR & CHAIN
Replace chain when cutters are too worn to sharpen
or when the chain becomes inoperable. Only use
replacement chain noted in this manual.
Inspect guide bar before sharpening chain. A worn
or damaged guide bar is unsafe. A worn or damaged
guide bar will damage chain. It will also make cutting
harder.
SHARPENING SAW CHAIN
WARNING: Remove the battery pack before
servicing. Severe injury or death could
occur from electrical shock or body contact
with moving chain.
Cutting edges on chain are sharp. Use protective
gloves when handling chain.
Keep chain sharp. Your saw will cut faster and more
safely. A dull chain will cause undue sprocket, Guide
Bar, chain, and motor wear. If you must force chain
into wood and cutting creates only sawdust with few
large chips, chain is dull.
LUBRICATE SPROCKET
WARNING: Wear heavy duty gloves when
performing any maintenance or service to
this tool. Always remove the battery pack
before performing any service or maintenance on
this tool.
NOTE: It is not necessary to remove the chain or bar
when lubricating the guide bar sprocket.
1. Clean the bar and sprocket
2. Using a grease gun, insert the tip of the gun
into the lubrication hole and inject grease until it
appears at the outside edge of the sprocket tip.
(See Fig. T)
3. To rotate the sprocket pull the chain by hand until

20
EN
the ungreased side of the sprocket is in line with the grease hole. Repeat the lubrication procedure.
FOR BATTERY TOOLS
The ambient temperature range for the use and storage of tool and battery is 0 ℃-45 ℃(32 ℉-113 ℉).
The recommended ambient temperature range for the charging system during charging is 0 ℃-40 ℃(32
℉-104 ℉).
TROUBLESHOOTING TABLE
The following table gives checks and actions that you can perform if your machine does not operate correctly. If
these do not identify/remedy the problem, contact your service agent.
WARNING: Switch off and remove plug from power source before investigating fault.
Symptom Possible Cause Remedy
Chainsaw fails to operate Low battery charge.
Chain brake not in the proper
position.
Charge both the battery packs.
Check to see if the chain brake is in
position . Refer to CHAIN BRAKE for
details.
Chainsaw operates
intermittently
Applying too much pressure
while cutting.
Not operating saw at full
speed.
Over heating
Loose connection.
Internal wiring defective.
Throttle trigger defective.
Applying relatively less pressure while
cutting.
Place the machine in a cool, ventilated
place to cool it down.
Contact service agent.
Contact service agent.
Contact service agent.
Dry chain No oil in reservoir.
Vent in oil ller cap clogged.
Oil passage clogged.
Rell oil.
Clean cap.
Clean oil passage outlet.
Kickback Brake/Run
Down Brake
Brake does not stop chain Contact service agent.
Chain/chain bar over-
heats.
No oil in reservoir.
Vent in oil ller cap clogged.
Oil passage clogged.
Chain is over tensioned.
Dull chain.
Rell oil.
Clean cap.
Clean oil passage outlet.
Adjust chain tension.
Sharpen chain or replace.
Chainsaw rips, vibrates,
does not saw properly.
Dull chain.
Chain worn out.
Chain teeth are facing in the
wrong direction.
Chain tension too loose.
Sharpen chain or replace.
Replace chain.
Reassemble with chain in correct direction.
Adjust chain tension.