EKR/EM 7
Conditions o guarantee
The conditions o guarantee applicable or this product are subject to those
published by the representative in the relevant country. Details regarding same
may be obtained rom the dealer rom whom the appliance was purchased.
For claims under guarantee the sales receipt must be produced.
Please note
KÜPPERSBUSCH built-in ovens may be combined only with KÜPPERSBUSCH
built-in hob units. The use o any other make o hob unit shall exempt Küp-
persbusch rom all liability.
Failure to observe this requirement will invalidate all granted certificates
and labels of approval.
Hints on installation
■ Make sure that the worktop is per ectly horizontal.
■ The ront, rear and lateral clearances around the hob unit must be maintai-
ned in accordance with the dimensional drawing.
A corner moulding o solid wood may be itted to the worktop at the back
o the hob unit provided that the minimum clearances are maintained.
For practical reasons the lateral clearance between the hob unit and an ad-
jacent tall cupboard unit must measure at least 300 mm.
■ Make sure that there is su icient clearance underneath the cut-out. Any ur-
niture battens must be cut away to leave an area which is at least the same
size as the cut-out itsel .
■ Make a point o ensuring that the plastic laminate or wood veneer on your
urniture surround has been applied by means o a heat-resistant adhesive
(100 °C).
■ The underside o the installed appliance must be protected by a panel which
prevents inadvertent contact with the live parts or connecting leads between
the control unit and the hob unit.
It must not be possible to remove the panel without tools.
■ Any cooker hoods or wall cupboards must have a vertical clearance o at
least 650 mm rom the hob unit.
■ Miniumum distance rom the hob edge to the adjacent wall: 40 mm.
It will be expedient to seal built-in sinks and other built-in appliances in the
worktop in the same way (protection against ingress o water).
We recommend you to seal the cut sur ace o the worktop recesses or itted
sinks and hobs with a protective water-proo paint.
The assembly seal is to be renewed a ter every dismantling operation. This
seal can be obtained rom our customer service under the spare part
No.538017.
Installation
■ Be extremely care ul when installingl Do not place or drop any sharp or
pointed tools (screwdrivers etc.) on the glass sur ace!
■ The glass-ceramic cooking area must have a level and lush bearing. Any
distortion may lead to racture o the glass panel.
■ Never use any electrically operated or air operated wrenches without an ad-
justable slipping clutch! Any overtightening must be avoided!
Making the worktop recess
– Make the worktop recess accurately with a good, straight saw blade or re-
cessing machine in accordance with the dimensions in the illustrations. The
cut edges should then be sealed so that no moisture can penetrate.
nsert the hob
– Care ully position the hob in the recess and irmly asten to the worktop with
the appropriate attachment elements.
– A ter attachment check the seal with the worktop.
Attachment EKR of worktops made of wood
– In the case o worktops made o wood, screw the attachment springs into
the recess as shown in the illustration and then press the hob evenly into
these springs rom above.
Attachment EKR of worktops made of stone and attachement EM
– Insert the angle nuts and introduce the glass ceramic hob rom above. Then
asten the hob with screws and attachment brackets rom below (see illu-
strations).
– Align the glass ceramic hob horizontally. There is a risk o breakage i
the hob is canted or subjected to stress during installation!
Attachment of worktops with an uneven surface
– When installing a hob into an uneven worktop, e.g. with a ceramic or similar
covering (tiles etc.), the seal on the hob is to be removed and the seal bet-
ween the hob and worktop made with plastic sealing materials, such as
heat-resistant silicone rubber (not included in scope o delivery).
– Clean the sur aces to be sealed in accordance with the manu acturer's in-
structions on the cartridge. Apply the compound in a continuous strip, pres-
sing it irmly against the gap to be sealed.
– Clean the sur aces to be sealed in accordance with the manu acturer's in-
structions on the cartridge. Apply the compound in a continuous strip, pres-
sing it irmly against the gap to be sealed.
Electrical Connection
Warning: This appliance must be earthed!
■ The built-in hob unit must be connected to the mains supply by a qua-
lified electrician who is authorized to carry out such work. Both legal
wiring regulations and the requirements of your local electricity sup-
ply board must be fully complied with.
■ Both the control unit and the oven must be isolated rom the mains during
installation.
– Switch o at the use box or remove the use.
– Make sure that the multiple pin plug belonging to the hob unit is cor-
rectly inserted into the matching socket o the control unit.
Service
The nameplate is located on the underside o the hob unit. The details given
on the nameplate must be quoted when calling in our service engineer or
when ordering replacement parts.
■ Should a repair become necessary, the appliance must be disconnected
rom the mains supply, i.e. by switching o at the use box or removing the
use.
