KYE Systems Corp. Genius SW-Flat2.1 800 User manual

ServiceGuide SW-Flat2.1 800
Version : 1.0 Page 1 of 16
SERVICE GUIDE
KYESYSTEMS CORP.
SW-Flat2.1 800

ServiceGuide SW-Flat2.1 800
Version : 1.0 Page 2 of 16
Version : 1.0
RevisionHistory
Version Date Change
1.0 2/5/2008

ServiceGuide SW-Flat2.1 800
Version : 1.0 Page 3 of 16
Table of Contents
Revision History …………………………………………………………………….2
Table of Contents ……………………………………………………………………3
Getting Started ………………………………………………………………………4
Conventions Used in this Guide ……………………………………….4
Safety Precautions ……………………………………………………..4
Chapter 1. How to Handle Defective Returns……………………………………..5
1.1 Overview …………………………………………………………..5
1.2 Problems …………………………………………………………...6
1.2.1 One or more channels no sound ………………..…7
1.2.2 Power LED (indicator) no light………………....…8
1.2.3 Volume , Bass no function...……..……….………..8
Chapter 2. Specifications ………………………………………….………………9
Chapter 3. Block Diagram …………………………………………….………….10
Chapter 4. Exploded View …………………………………………….………….11
Chapter 5. Part List …………………………………………………….…………14
Chapter 6. Schematic Diagram ………………………………………….………..15
Chapter 7. Important Notes ……………………………………………….………16
7.1 Packing Requirement for Sending the PCB Assembly by Post. …..16
7.2 Short of Spare Parts while Repairing a Speaker System ………..…16

ServiceGuide SW-Flat2.1 800
Version : 1.0 Page 4 of 16
Getting Started
Conventions Used in this Guide
Pay Special Attention : Instructions that are important to remember and
may prevent mistakes .
Caution : Information that, if not followed, may result in damage to the
product .
Safety Precautions
The following precautions should be observed in handling the speaker
Described in this guide :
Place the speakers on a flat, level and stable surface.
Do not place the speakers in environments subject to mist, smoke,
vibration, excessive dust, salty or greasy air, or other corrosive gases
and fumes.
Do not drop or jolt the speakers.
Do not allow anything to drop into the subwoofer case through its
ventilator, as it could result in fatal electric shock or fire .
Place the unit far enough from other equipments for good heat
dissipation .
Disconnect the AC adaptor from the AC outlet before performing
any maintenance on the speakers .
Do not perform any maintenance with wet hand .
Prevent foreign substances, such as water, other liquids or chemicals ,
From entering the speakers while performing maintenance procedures
on the speakers .

ServiceGuide SW-Flat2.1 800
Version : 1.0 Page 5 of 16
Chapter 1. How to Handle Defective Returns
1.1 Overview
Verifying problems
Proceeding necessary tests
Receiving Defective speakers from
Customers
Analyzing possible malfunction
causes
Deciding & proceeding the
rectification methods
Replace necessary defective parts
Proceeding tests to
Verif
y
if the s
p
eaker is
functionin
g
normall
y
Return the speakers with proper
repackaging to customers
Function NG
Function OK
Function OK
Function NG

ServiceGuide SW-Flat2.1 800
Version : 1.0 Page 6 of 16
1.2 Problems
Item Problem Description
1.2.1 Oneormorechannelsnosound
1.2.2 PowerLED(indicator)nolight
1.2.3 Volume,Bassnofunction

ServiceGuide SW-Flat2.1 800
Version : 1.0 Page 7 of 16
Attention
1.2.1 One or more channels no sound
Problem
Solutions
Please follow the numbered sequence marked within parenthesis given in individual
Flow chat, in that this is the best-recommended sequence to rectify the problems.
One or more channels no sound
Broken or short circuit Defective
U1, U2, U3, U4
wired control cable
Speaker cable dis-connect
or speaker damaged
Check solder points on
PCB
Check and Replace
defective IC
Re-connect speaker
cable or replace
defective speaker(s)
Analyzer and
Identify the Causes

ServiceGuide SW-Flat2.1 800
Version : 1.0 Page 8 of 16
1.2.2 Power LED (indicator) no light
Problem
Solutions
1.2.3 Volume , Bass no function
Problem
Solutions
Power LED (indicator) no light
Power switch or LED
defective
Defective D2~D5,
SW1 , R15 , U4
C34 , C35 , C36
wired control cable
AC cord of adaptor
disconnected or defective
Re-solder or replace
defective component(s)
Analyzer and
Identify the Causes
Volume , Bass no function
Broken or short circuit Volume: Defective VR2
Bass: Defective VR1
Check solder points on PCB
Analyzer and
Identify the Causes
Check and Replace defective
components

ServiceGuide SW-Flat2.1 800
Version : 1.0 Page 9 of 16
Chapter 2. Specifications
Woofer
NO. Description Unit Specifications
1 Out Power at THD 10% W 9 ±0.5
2 Sensitivity mV 720 ±50
3 Freq. Response (Top -3dB) Hz 56 ~ 610 ±10%
4 S/N ratio dB ≧60
5 Hum & Noise (Vol.: max) mV ≦ 2
Satellite
NO. Description Unit Specifications
1 Out Power at THD 10% W ≧3
2 Sensitivity mV 570 ±50
3 Freq. Response (Top -3dB) Hz 225 ~ 20K ±10%
4 Separation dB ≧40
5 S/N ratio dB ≧70
6 Hum & Noise (Vol.: max) mV ≦ 2

ServiceGuide SW-Flat2.1 800
Version : 1.0 Page 10 of 16
Chapter 3. Block Diagram
AUDIO IN
Volume
Control
Power
Amplifier
R. Satellite
L. Satellite
Woofer
woofer volume
AC IN Adaptor &
Rectifier
FILTER Standby
Switch
Wired Control Box

ServiceGuide SW-Flat2.1 800
Version : 1.0 Page 11 of 16
Chapter 4. Exploded View
Woofer

ServiceGuide SW-Flat2.1 800
Version : 1.0 Page 12 of 16
Satellite

ServiceGuide SW-Flat2.1 800
Version : 1.0 Page 13 of 16
Wired Control Box

ServiceGuide SW-Flat2.1 800
Version : 1.0 Page 14 of 16
Chapter 5. Part List
No. DESCRIPTION Qty UNIT Part No.
1 SW-Flat2.1 800/Body/Satellite 2 PC 19-101-01
2 Loud Speaker, 4 ohm 3W 2 PC E1049-33
3 Rubber Pad, SW-lat2.1 800/Satellite 4 PC 19-100-01
4 SW-Flat2.1 800/Body/Woofer 1 PC 19-101-02
5 Loud Speaker, 4 ohm 10W 1 PC E1049-32
6 PCBA, SW-Flat2.1 800 1 PC 19-101-03
7 IC, UTC8227 1 PC E1065-18
8 IC, YW4558 1 PC 11-100-04
9 IC, TDA7499 1 PC E1065-16
10 IC, L7812CV 1 PC E1065-15
11 Rubber Pad, SW-Flat2.1 800/Woofer 5 PC 19-100-02
12 Adaptor, 120V:13.5VAC & 1.2A(US)
1 PC
E1074-125
13 Adaptor, 220V:13.5VAC & 1.2A(AR) E1074-131
14 Adaptor, 230V:13.5VAC & 1.2A(EU) E1074-124
15 Adaptor, 240V:13.5VAC & 1.2A(AU) E1074-132
16 Adaptor, 240V:13.5VAC & 1.2A(UK) E1074-127
17 Audio Cable, 3.5mm plug, 1.5M 1 PC E1066-25
18 Manual, SW-Flat2.1 800 1 PC 12030263100-A
19 S/N Label, SW-Flat2.1 800 2 PC 19-102-01
20 Gift Box, SW-Flat2.1 800 1 PC 12000311100-A
21 Bubble sheet, SW-Flat2.1 800 1 PC 19-102-02
22 Round Yellow Type Label (on Gift Box) 1 PC 19-102-03
23 Carton, SW-Flat2.1 800 1/10 PC 12100173100-A

ServiceGuide SW-Flat2.1 800
Version : 1.0 Page 15 of 16
Chapter 6. Schematic Diagram

ServiceGuide SW-Flat2.1 800
Version : 1.0 Page 16 of 16
Chapter 7. Important Notes
7.1 Packing Requirement for Sending the PCB Assembly by Post
PCB assembly is a kind of sophisticated electronic circuit board. Well
packing will be required when sending them by post.
* Some sophisticated IC components are mounted on the PCB assembly,
hence it is necessary to pack each PCB assembly with a separate static
protecting bag, in order to avoid static electricity.
* Reliable external packing is also very important when sending PCB
assembly by post, in that it would avoid unnecessarily lost or damage.
7.2 Short of Spare Parts while Repairing a Speaker System
If you are short of spare parts when you have some speaker systems waiting
to be repaired, it would be recommended to take the necessary parts form
one speaker system, so that you may have the as many speaker systems.