KYOKUTOH AB2 Series User manual

Please read this instruction manual carefully
before operating this unit and use our product correctly.
After reading this instruction manual, be sure to keep it in a place where a person
who uses or manages the equipment can check it at any time.
Air Blow Unit（AB2-**）
Instruction Manual
First Edition 2020.09.23

1
TABLE OF CONTENTS
1. Safety Precautions
2. Parts List
3. Assembly Procedure
4. Maintenance
5. Order Model
Contact
2
3
4
9
8
8

2
1. Safety Precautions
■Introduction
The Air Blow Unit (AB2) is a tool for our Dressers to prevent chips being stuck
while dressing cap tips.
This is a product exclusively for preventing chips being stuck. Do not use for
any other purpose. Do not use for Changers other than the specified models.
We do not assume any responsibility for malfunctions, repairs, accidents, or
others which occurred by using with un-specified models or by other purpose.
■Regarding Signs
It indicates contents informing possibilities of death or
serious injury in case of incorrect handling.
It indicates contents informing possibilities of injury due
to handling error or occurrence of material damages.
This symbol indicates operations that should not be done.
This symbol indicates operation that should be done.

3
2. Parts List
■Example for CDK-R
No.
Name
Model
QTY
Note
1 Air Blow Nozzle Holder Block AB2-BLOW-BL-03-001 1
2 Air Blow Nozzle AB2-BLOW-NZ-01-003-S 1
3 Air Blow Bracket for K-Model AB2-BLOW-K-BR-01-001 1 For CDK-R
4 Samini Compressed Spring 12-1021 1
5 CKD Solenoid Valve AB2-01-3-A-DC24V 1
6 PISCO Fitting PL6-01 2
7 PISCO Fitting PL6-M5 1
Tighten with ②.
Tightening
torque :1.0N/m
Loctite：High-Strength
8 PISCO Spatter Tube（φ6）FB0640 1 170mm
③
④
②
①
⑤
⑥
⑥
⑦
⑧
M5*10 3-sems
M3*14 Hex Socket Cap Screw
M3 Spring Washer
M5*25 Hex Socket Cap Screw
M5 Spring Washer
M5 Flat Washer

4
3. Assembly Procedure
*Image below is an example of installing to CDK-R.
■Precautions
1. Make sure that the air flow is following the arrow direction.
2. Check the air pressure. (range: 0.3 ～0.5 MPa)
3. Some parts are made of Synthetic Resin. Excessive screw tightening may
damage the product.
Arrow is marked on the
back side。
Air OUT
Air IN

5
■Procedure
1. Remove the screws from the Dresser, then attach the bracket with screws
enclosed.
（M5*25 Hex Socket Cap Screw, M5 Spring Washer, M5Flat Washer is used.
Tightening torque 4.5N/m）
*This product is available to both left and right side by flipping the bracket. Be
careful of the orientation when attaching.
2. Attach Nozzle ASSY to the bracket. (Use M3*14 Hex Socket Cap Screw, M3
Spring Washer. Tightening torque 1.0N/m)
Screw holes must be vertical when attached.

6
3. Attach the Solenoid Valve.
(Use M5*10 M5*10 3-sems. Tightening torque 4.5N/m)
4. Attach the Spatter Tube.

7
5. Completion

8
4. Maintenance
Changing Cutter / Holder can be done without removing the Air Blow Unit.
Squeeze the Nozzle when changing the Cutter / Holder as the image below.
5. Order Model
Model
Correspond Dresser
Note
AB2-K CDK-R
AB2-KSG CDK-SG
AB2-BA CDK-BAYO
AB2-SV CD-SVR
*Special parts may be required according to position of dresser or gun motion.
Please call us for more information.

9
Contact
Contact us if there is any damage or machine defects in our products.
KYOKUTOH CO., LTD.
181-1, Nakayashiki, Orido-cho, Nisshin, Aichi 470-0115 Japan
TEL [phone] FAX [phone]
E-Mail: [e-mail]
http://www.kyokutoh.com
KANTO SALES OFFICE
TEL [phone] FAX [phone]
HIROSHIMA SALES OFFICE
TEL [phone] FAX [phone]
CHANGER ＆DRESSER CORPORATION
1527 ITC Way, Anniston, AL 36207 U.S.A
TEL [phone] FAX [phone]
http://www.changer-dresser.com
KYOKUTOH CHINA
73 Huagang Street, Xiuquan Town, Huadu District,
GuangZhou City, GuangDong Province, China.
TEL [phone] FAX [phone]
http://www.kyokutoh.com.cn
KYOKUTOH THAILAND
339/2 Soi Phattanakarn 69, Phattanakarn Road, Prawet,
Bangkok 10250 THAILAND
TEL [phone] FAX [phone]
http://www.kyokutoh.co.th
KYOKUTOH KOREA
117, Tawon TAKRA II Industry Center, Dongsan-ro 76,
Danwon-gu, Ansan-si, Gyeonggi-do, Korea 15434
TEL [phone] FAX [phone]
KYOKUTOH EUROPE
Radlkoferstr. 2 81373 Muenchen, Germany
TEL [phone] FAX [phone]
http://www.kyokutoh.de
KYOKUTOH WELD INDIA
Office No.19, 3rd Floor, Aditya Centeegra, FC Road, Deccan,
Pune - 411004
TEL [phone] FAX [phone]