La Crosse Technology Wireless Weather Station User manual

WIRELESS 868 MHz WEATHER STATION
Instruction Manual
INTRODUCTION:
Congratulations on purchasing this Weather station with wireless 868MHz transmission. It not
only displays the indoor temperature and humdity but also receives the outdoor temperature. It is
further acting as a DCF-77 radio controlled clock. With the totally 15 different weather forecast
icons featured by "weather man", users can easily observe the forecast weather condition and
will no longer worry the sudden weather change. This innovative product is ideal for use in the
home or office.
1
« Instant Transmission+» is the up and coming state-of-the-art new wireless
transmission technology, exclusively designed and developed by LA CROSSE
TECHNOLOGY.
“IT +” offers you an immediate update of all your outdoor data measured from the
transmitters: follow your climatic variations in real-time!

FEATURES:
The Weather station
LCD
Display
Function
Keys
Foldout
Stand
Battery
compartment
cover
Hanging hole
2

3
•DCF Radio controlled time function or manual time setting options
•DCF time reception ON/OFF setting
•12/24 hour display
•Hour and minute display
•Time zone option ±12 hours
•Wireless transmission at 868 MHz
•Signal reception intervals at 4-second
•Display indoor and outdoor temperature and indoor humidity (% RH)
•Temperature display in degrees Celsius (°C) or Fahrenheit (°F) selectable
•Weather forecasting with 15 easy-to-read weather forecast signs featured by
Weatherman
•Weather forecasting icon sensitivity setting
•Indoor and Outdoor temperature display with MIN/MAX recording
•All MIN/MAX temperature records show date and time received
•All MIN/MAX recordings can be reset
•Can take up to three outdoor transmitters
•LCD contrast setting
•Low battery indicator
•Table standing/ Wall mounting

The Outdoor Temperature Transmitter
•Remote transmission of outdoor temperature to Weather Station
by 868 MHz
•Shower proof casing
•Wall mounting case (Mounting at a sheltered place. Avoid direct
rain and sunshine)
SETTING UP:
When one transmitter is used
1. First, insert the batteries into the Temperature transmitter. (see “Install and replace
batteries in the Temperature transmitter“).
2. Immediately after and within 25 seconds, insert the batteries into Weather station (see
“Install and replace batteries in the Weather station”). Once the batteries are in
place, all segments of the LCD will light up briefly. Following the time as 0:00 and the
"weather man" icon will be displayed. If these are not displayed after 60 seconds,
remove the batteries and wait for at least 10 seconds before reinserting them.
4

5
3. After inserting the batteries, the Weather station will start receiving data from the
transmitter. The outdoor temperature and the signal reception icon should then be
displayed on the Weather station. If this does not happen after 3 minutes, the batteries
will need to be removed from both units and reset from step 1.
4. In order to ensure sufficient 868 MHz transmission however, this should under good
conditions be a distance no more than 100 meters between the final position of the
Weather Station and the transmitter (see notes on “Mounting” and “868 MHz
Reception”).
When more than one transmitter is used
1. User shall remove all the batteries from the weather station and transmitters and wait for
60 seconds if setting has been done with one transmitter before.
2. Insert the batteries to the first transmitter.
3. Within 25 seconds of powering up the first transmitter, insert the batteries to the Weather
Station. Once the batteries are in place, all segments of the LCD will light up briefly.
Following time as 0:00 and the weather man icon will be displayed. If they are not shown
in LCD after 60 seconds, remove the batteries and wait for at least 60 seconds before
reinserting them.
4. The outdoor temperature from the first transmitter (channel 1) should then be displayed on
the Weather station. Also, the signal reception icon will be displayed. If this does not
happen after 2 minutes, the batteries will need to be removed from both units and reset
from step 1.

6
5. Insert the batteries to the second transmitter as soon as the outdoor temperature readings
from the first transmitter are displayed on the Weather station.
Note: User shall insert the batteries into the second transmitter within 25 seconds of reception
of the first transmitter.
6. The outdoor temperature from the second transmitter and the "channel 2" icon should
then be displayed on the Weather station. If this does not happen after 2 minute, the
batteries will need to be removed from all the units and reset from step 1.
7. Insert the batteries to the third transmitter as soon as the "channel 2" icon and outdoor
data are displayed on the Weather station. Then within 2 minutes, the channel 3 outdoor
data from the third transmitter will be displayed and the channel icon will shift back to "1"
once the third transmitter is successfully received. If this is not happen, user shall restart
the setting up from step 1.
Note: User shall insert the batteries into the third transmitter within 25 seconds of reception of
the second transmitter.
8. In order to ensure sufficient 868 MHz transmission however, this should under good
conditions be a distance no more than 100 meters between the final position of the
Weather Station and the transmitter (see notes on “Mounting” and “868 MHz
Reception”).

7
IMPORTANT:
Transmission problems will arise if the setting for additional sensors is not followed as described
above. Should transmission problems occur, it is necessary to remove the batteries from all units
and start again the set-up from step 1.
9. Once the remote temperature has been received and displayed on the Weather station,
the DCF time (radio controlled time) code reception is automatically started. This takes
typically between 3-5 minutes in good conditions.
If after 10 minutes, the DCF time has not been received, press the SET key to manually enter a
time initially.
Note:
Daily DCF reception is done at 02:00 and 03:00 every day. If the reception at 03:00 is not
successful, then at 04:00 and 05:00 and 06:00 there are other tries, until one is successful. If the
reception at 06:00 is still not successful, then the next try takes place at 02:00 next day.
If reception is successful, the received time will override the manually set time. The date is also
updated with the received time. (Please refer also to notes on “DCF Reception” and “Manual
Time Setting”)

BATTERY INSTALLATION
INSTALL AND REPLACE BATTERIES IN THE WEATHER STATION
The Weather station uses 2 x AA, IEC LR6, 1.5V batteries. To install and replace the batteries,
please follow the steps below: 1. Remove the cover at the back of the weather station.
2. Insert batteries observing the correct polarity (see
marking).
3. Replace compartment cover.
INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE TRANSMITTER
The Temperature Transmitter uses 2 x AA, IEC LR6, 1.5V battery. To install and replace the
batteries, please follow the steps below:
8

9
1. Pull out the battery holder at the bottom of the transmitter.
2. Insert the batteries, observing the correct polarity (see marking).
3. Replace the battery holder on the unit.
Note:
In the event of changing batteries in any of the units, all units need to be reset by following the
setting up procedures. This is because a random security code is assigned by the transmitter at
start-up and this code must be received and stored by the Weather station in the first 3 minutes
of power being supplied to it
BATTERY CHANGE:
It is recommended to replace the batteries in all units regularly to ensure optimum accuracy of
these units (Battery life See Specifications below).

Please participate in the preservation of the environment. Return used
batteries to an authorised depot.
FUNCTION KEYS:
Weather station:
The weather station has four easy to use function keys.
SET key (Setting):
•To enter the set mode for the following functions: LCD contrast, Time zone, Time
Reception ON/OFF, 12/24 hour display, Manual time, Year, Month, Date, Temp unit °C/°F,
and Weather forecast sensitivity settings.
SET key
MIN/
MAX key
+ key
CH key
10