Lab.gruppen Fp+ series fp 10000q Instruction manual

A Benchmark For Touring Amplification

Over the past decade, the tight and transparent sound of

Lab.gruppen touring amplifiers has earned the praise of renowned

FOH engineers and leading sound rental companies worldwide.

FP 10000Q, the flagship four-channel model of the FP+ Series,

continues this tradition. At the core of the FP 10000Q’s performance

is the patented Class TD output stage, a breakthrough amplifier

topology that approaches the exceptional efficiency of Class D while

retaining the sonic purity of proven Class B designs. Further contri-

buting to the remarkable efficiency of the FP 10000Q is a Regulated

Switch Mode Power Supply (R.SMPS), which gives the added benefit

of stabilizing rail voltages to the output even with wide fluctuations of

mains voltage. A highly refined and updated circuit layout optimizes

the interaction of R.SMPS and Class TD to produce the extraordinary

power density of the FP 10000Q.

To keep its cool under extreme demands, the FP 10000Q relies on

Lab.gruppen’s proprietary Intercooler. This innovation uses thou-

sands of copper fins to multiply the exposed heatsink surface’s

rapid heat dissipation. Also, all output devices are mounted trans-

verse to the airflow for uniform cooling. As a result, the FP 10000Q

delivers Lab.gruppen’s trademark “all the power, all the time” with no

degradation of sonic performance.

To maximize headroom in any application, the FP 10000Q offers

adjustable input gain along with Lab.gruppen’s exclusive Voltage

Peak Limiter (VPL). Adjustable on a per-channel basis, VPL opti-

mizes the output for any load, from a single massive subwoofer to a

series of HF compression drivers.

The comprehensive warning and protection features on the

FP 10000Q safeguard output circuits and connected loads while

also extending amplifier life and minimizing chance of service inter-

ruptions. Whether it’s a matter of faulty wiring, improper use, or ex-

treme ambient temperatures, the FP 10000Q gives clear indication of

any problems. Automatic protection measures engage only at critical

thresholds. Operating conditions are re-checked every six seconds

and, if a fault is detected, normal operation is resumed when mea-

surements return to nominal.

The FP 10000Q is shipped with a NomadLink network interface as

standard. In conjunction with DeviceControl software, or the leading

third party control platforms, NomadLink network allows monitoring

of all key amplifier parameters and remote control of power on/off,

channel mutes, and channel solo functions. (NomadLink requires the

separate NLB 60E NomadLink Bridge & Network Controller).

▸Very high power and channel density – The four-channel

FP 10000Q delivers a total of 10000 W (4 x 2500 W @ 2 ohms) in

only 2U.

▸Four-channel flexibility – Four channels in one cabinet increases

efficiency, flexibility and value in powering monitor systems, line

arrays, and bi- or tri-amped systems. Adjacent channels bridge-

able for 2- or 3-channel operation.

▸Lab.gruppen sound quality – FP 10000Q amplifiers maintain

the impeccable sonic performance standards set by the original

fP Series, with the same durability and even greater efficiency.

▸NomadLink®network ready – Monitoring and control of key

functions accessible via the intuitive DeviceControl software and

the robust, daisy-chained NomadLink network, as well as by the

leading third party control platforms.

▸Patented Class TD®amplifier topology – Road-proven output

stage delivers Class B audio quality with Class D efficiency.

▸Regulated Switch Mode Power Supply (R.SMPS™) – Output

power remains constant even with significant drops in the mains

voltage.

▸Efficient cooling system – Unique, lightweight Intercooler®cop-

per cooling system dissipates more heat to allow extended peak

output.

▸Adjustable parameters – Selectable Gain, scalable Voltage Peak

Limiter (VPL

™), and bridge-mode operation allow custom configu-

ration for any system or application.

▸XLR input connectors

▸Heavy-duty binding post or speakON®output connectors

▸Comprehensive protection and warning – Excessive output

current, DC, high temperature, very high frequency (VHF), short

circuit, open load, mains fuse protection, and soft start.

FP 10000Q

Technical Data

FP+ Series: Dedicated Touring Ampliﬁers

Item no. TDS-FP10000Q_V9

Lab.gruppen ab ▸Sweden

internationaL contact ▸ info@Labgruppen.com | uS & canada contact ▸ info@tcg-americaS.com

www.labgruppen.com

General

Number of channels 4

Peak total output both channels driven 10000 W

Peak output voltage per channel 150 V

Max. output current per channel 50 A peak

Max. Output Power 2 ohms 4 ohms 8 ohms 16 ohms

Per ch. (both ch.’s driven) 2500 W 2100 W 1300 W 660 W

Bridged per ch. 3) 5000 W 4200 W 2600 W

Performance with Gain: 35 dB and VPL: 150 V

THD 20 Hz - 20 kHz for 1 W <0.1%

THD at 1 kHz and 1 dB below clipping <0.05%

Signal To Noise Ratio >112 dBA

Channel separation (Crosstalk) at 1 kHz >70 dB

Frequency response (1 W into 8 ohms) +0/-3 dB 6.8 Hz - 34 kHz

Input impedance 20 kOhm

Common Mode Rejection (CMR) >54 dB, 20 Hz to 20 kHz

Output impedance @ 100 Hz 32 mOhm

Voltage Peak Limiter (VPL), max. peak output

VPL, selectable per ch. 150, 121, 101, 83, 70, 56, 47, 38 V

VPL, selectable when bridged 1) 300, 242, 202, 166, 140, 112, 94, 76 V

Voltage Peak Limiter mode (per ch.) Hard / Soft

Gain and Level

Amplifier gain selectable (all channels) 1)

– rear-panel switches

23, 26, 29, 32, 35, 38, 41, 44 dB

Default gain 35 dB

Level adjustment (per ch.) Front-panel potentiometer, 31 position detented from -inf to 0 dB

Connectors and Switches

Input connectors (per ch.) 3-pin XLR, electronically balanced

Output connectors (per ch.) Neutrik speakON or Binding Posts (must be specified upon order)

Output bridge mode per two ch.’s A+B - Ch. A is signal input source

NomadLink network On board, 2 x RJ45 etherCON®connectors, IN and OUT

Intelligent fans (on/off) Yes, depending on presence of output signal

Power on/off and Remote enable on/off Individual switches on front-panel

Cooling Two fans, front-to-rear airflow, temperature controlled speed

Front-panel indicators:

Common NomadLink network; Power Average Limiter (PAL) 2); Power on

Per channel Signal present / High-impedance; -20 dB, -15 dB, -10 dB and -4 dB output signal;

Voltage Peak Limiter (VPL); Current Peak Limiter (CPL); Very High Frequency (VHF); High temperature; Fault; Mute

Power

Operating voltage, 230 V / 115 V nominal 4) 130-265 V / 65-135 V

Minimum power-up voltage, 230 V / 115 V 171 V / 85 V

Power Average Limiter (PAL) 2) Ye s

Soft start / Inrush Current Draw Yes / max. 5 A

Mains connector 230 V CE: 16 A, CEE7; 115 V ETL: 30 A Twist lock

Dimensions W: 483 mm (19”), H: 88 mm (2 U), Overall D: 396 mm (15.6”), Mounting D: 358 mm (14.1”)

Weight 12 kg (26.4 lbs.)

Finish Black painted steel chassis with black painted steel / aluminum front

Approvals CE, ANSI/UL 60065 (ETL), CSA C22.2 NO. 60065, FCC

Note 1): Automatic -6 dB gain compensation when bridging channels.

Note 2): PAL can reduce the maximum output power to keep the power supply operating safely, and/or to prevent excessive current draw tripping the mains breaker.

Refer to the FP+ Operation Manual section 7.5.8 Power Average Limiter (PAL) for more information.

Note 3): The amplifier will be fully operational at bridge-mode 2 ohm loads, but due to physical constraints in the construction, the max. output power will not be

significanty higher than running individual channels and therefore this mode of operation is not

recommended.

Note 4): Separate 230 V or 115 V versions available. Not selectable on the amplifier.

All specifications are subject to change without notice.

Intercooler, NomadLink and Class TD are national and/or international registered trademarks of Lab.gruppen AB. R.SMPS and VPL are trademarks of Lab.gruppen AB. All other