Lacertosus HALF RACK PRO User manual

Allen bolt
M12x105
x12
Allen bolt
M12x25
x4
Nut
M12
x12
Flat washer

x28
Spring washer
x4
Wrench
N19
For a simpler and faster
assembly we recommend
the use of two wrenches
*
Thank you for choosing another high quality product from Lacertosus®, enjoy the installation and please get back to
us in case you are facing problems!
Scan this qr code for
the online instructions
in english or italian
And if this manual isn’t enough:
2
0
1
2

4
5
6
7
8
9
10
11
12

14
15
16
17
18
19
20
21
22

[cm]

Assemble the U-base on the ground
Assemble the triangular galvanized plates without tightening them
x4 x4 x8
x4 x4 x8
ASSEMBLY INSTRUCTIONS / HALF RACK
Note:
After this step, If you also
bought the adjustable pull
up bar, please go to page 6
3

Assemble the poles on the base, thightening the bolts
Note: repeat this operation for each
pole’s hole
Tighten the remaining bolts, securing the pole to the plates
x4 x4 x4
x4 x4 x8
4

Add the J-Hook and enjoy your new training partner!
5.
5

After the operations indicated in point 2., on the ground, insert the galvanized pipe inside the pole
WARNING:
During this operation pay attention to
don’t ever put your ngers inside the
poles’ holes

x4 x4 x8
6
Note:
For proper pairing
make sure that the
logo is facing up


Assembly the black bar, inserting it in the upper holes and block it with the screws
x4 x4 x4
Note: repeat this operation for each
pole’s hole
x4 x4 x4
5.
6.
7

Tighten the remaining bolts, securing the pole to the plates
x4 x4 x8
7.
Add the J-Hook and enjoy your new training partner!
8.
8
CAUTION:
With the adjustable pull up bar mounted, it is
strongly recommended to fasten the rack to
the ground


|Lacertosus®is a registered trademark |
release date 11/2020


0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
[cm]
Vite
M12x105
x12
Vite
M12x25
x4
Dado
M12
x12
Rondella

x28
Grover
x4
Chiave
N19
Per un montaggio più
semplice e veloce si con-
siglia l’uso di due chiavi
*
-
trare problemi ti preghiamo di contattarci!
Scannerizza il codice
QR per accedere alle
istruzioni online
E se pensi che questo manuale non sia abbastanza
2

Montare la base a U sul terreno
Montare le piastre triangolari zincate senza serrarle
x4 x4 x8
x4 x4 x8
Note:

acquistato la Sbarra per trazioni

3


Note: ripetere questa operazione per
ogni foro del palo

x4 x4 x4
x4 x4 x8
4

Aggiungi i j-hook e goditi la tua nuova attrezzatura!
5.
5

Dopo l’operazione indicata la punto 2.
AVVERTENZA:
Durante questa operazione prestare attenzione
anon mettere mai le dita all’interno dei fori dei
pali 

x4 x4 x8
6
Note:
Per un corretto accoppia-
mento assicurarsi che il
logo sia rivolto verso l’alto



x4 x4 x4
Note: ripetere questa operazione per
ogni foro del palo
x4 x4 x4
5.
6.
7


x4 x4 x8
7.
Aggiungi i j-hook e goditi la tua nuova attrezzatura!
8.
8
ATTENZIONE:
Con la barra per trazioni regolabile
 si consiglia vivamente di
ssare il rack a terra utilizzando le
apposite ange triangolari e i piedini

|®is a registered trademark |
release date 11/2020
