Laguna Tools 1632 User manual

Producer:
Laguna Tools Inc
744 Refuge Way, Suite 200
Grand Prairie, Texas 75050
USA
Phone: [phone]
Website: www.lagunatools.com
Distributor:
IGM nástroje a stroje s.r.o.
Ke Kopanině 560, 252 67, Tuchoměřice
Czech Republic, EU
Phone: [phone]
E-mail: [email protected]
Website: www.igmtools.com
2022-03-30
151-1632 LAGUNA Drum Sander Manual EN v2.0 A4ob
www.igmtools.info
PDF ONLINE
1632
Drum Sander
Operating Instructions

-2-www.igmtools.com
EC DECLARATION OF CONFORMITY
We
(Manufacturer)
Laguna Tools Inc.
2072 Alton Parkway, Irvine, California 92606, USA
Declare that the product name: Woodworking Drum Sander
Model Name :
71632, 71938, 71938-D, 72550
Conform with the essential safety requirements of the relevant European Directive:
-Machinery Directive 2006/42/EC
-Electromagnetic Compatibility Directive 2014/30/EU
The person who compile technical file established within the EU:
Name:
IGM nastroje a stroje s.r.o.
Address:
Tel.:
Email:
Ke Kopanine 560, Tuchomerice , CZ-252 67
[phone]
[e-mail]
Mounting and connecting instructions defined in catalogues and technical construction files must be respected
by the user.
They are based on the following standards：
EN ISO 12100:2010 Safety of Machinery - General principles for design / Risk Assessment and Risk reduction.
EN 60204-1:2006+AC:2010 Safety of machinery –Electrical equipment of machines, part 1 : General
requirements.
EN 13849-1:2015 Safety of machinery –Safety –related parts of control systems Part 1: General principles for
design
EN 50370 -1:2005 Electromagnetic compatibility (EMC) –Product family standard for machine tools –Part 1:
Emission.
EN 50370 -2:2003 Electromagnetic compatibility (EMC) –Product family standard for machine tools –Part 2:
Immunity.
EN 61000-4-2: 2009 Electrostatic (ESD)
EN 61000-4-4: 2012 Electrical fast transient/burst requirements (EFT/Burst)
EN 61000-4-6: 2014 Immunity to conducted disturbances, induced by radio-frequency fields (CS)
Responsible for the documentation: Head Product Management, Laguna Tools Inc.
Name : Torben Helshoj
Responsibility
Authorized Signature
Date : Oct. 15, 2021
Place : Laguna Tools Inc.
2072 Alton Parkway, Irvine, California 92606, USA
Telephone: [phone]
Fax: [phone]

-3-www.igmtools.com
Table of Contents
1. Declaration of Conformity
2. Warranty
3. Safety
Authorized Use
General Safety Notes
Hazards
Grounding Instructions
4. Machine Specication
5. Transport and Setup
Setup
6. Setting and Adjustment
Drum Sander Adjustment
Installing and Wrapping Abrasives
7. Machine Operation
8. Maintenance
9. Troubleshooting
1. Declaration of Conformity
We declare that this product is in compliance with the directive and the
standard mentioned on the previous page of this manual.
2. Warranty
The company IGM Tools & Machinery s.r.o. always strives to deliver a
product of high quality and e󰀩ciency.
The application of the warranty is governed by the valid Business
Conditions and the Warranty Conditions of the company IGM Tools &
Machinery s.r.o.
3.Safety
3.1 Authorized Use
This machine is designed for sanding wood and wooden products only.
Sanding of other materials is not permitted but can be performed in
specic cases only after consulting the manufacturer.
The machine is not suitable for wet sanding.
The required minimum age must be observed.
The machine must only be used in a technically perfect condition.
In addition to the operating instructions, also read the safety requirements
and your country’s applicable regulations.
You should observe the generally recognized technical rules and safety
requirements concerning the operation of woodworking and metalworking
machines.
Neither the manufacturer nor the supplier is liable for damage resulting
from unauthorized use of the machine. Responsibility is transferred
exclusively to the operator.
3.2 General Safety Notes
Woodworking machines can be dangerous if not used properly.
Read and understand the entire operating manual before attempting
assembly or operation.
Protect this operating manual from dirt and humidity and pass it over to the
new owner if you part with the machine.
No changes to the machine may be made.
Daily inspect the function and existence of the safety appliances before
you start the machine. Correct all defects or damaged safety appliances
immediately. The machine must only be used in a technically perfect
condition.
Protect long hair with a cap or hair net. Remove all loose clothing, rings,
watches and other jewellery. Wear safety shoes; never wear leisure shoes
or sandals. Follow personal protection guidelines.
Do not wear gloves while operating this machine!
Install the machine so that there is su󰀩cient space for safe operation and
workpiece handling.
The machine must be bolted on rm and levelled surface and must be
properly lighted.
Always wear a protective mask in a dusty environment.
Keep work area well lighted.
Make sure the machine stands on a board.
Make sure that the power cord does not impede work. Keep work area
clean. Never reach into the machine while it is operating or running down.
Stay alert! Give your work undivided attention. Use common sense. Do
not operate the machine under the inuence of drugs, alcohol or any
medication.
Keep children and visitors a safe distance from the work area. Never
leave a running machine unattended. Before you leave the workplace
switch o󰀨 the machine.
Do not use the machine in a dump environment and do not expose it to
rain.
Wood dust is explosive and can also represent a risk to health. In
particular dust from tropical woods and hardwoods like beech and oak, is
classied as a carcinogenic substance.
Focus on the position of your ngers and other parts of your body when
working.
Do not start the machine without safety appliances.
It is important to clamp all workpieces.
Machine only stock which rests securely on the table.
Do not remove chips and workpiece parts until the machine is at a
standstill.
Minimum workpiece length is 60 mm.
Do not stand on the machine.
Repair work on the electrical installation may be carried out by a qualied
electrician only.
Have a damaged or worn power cord replaced immediately.
Have a damaged abrasive replaced immediately.
3.3 Hazards
When using the machine according to regulations some remaining
hazards may still exist.
EN - English
Operating Instructions (Original)
Dear Customer,
many thanks for the condence you have shown in us with the purchase of your new Laguna Tools machine. This manual has been
prepared for the owner and operators of an IGM LAGUNA 1632 SuperMax Drum Sander to promote safety during installation,
operation and maintenance procedures. Please read and understand the information contained in these operating instructions and the
accompanying documents. To obtain maximum life and e󰀩ciency from your machine, and to use the machine safely, read this manual
thoroughly and follow instructions carefully.
We wish you many work and personal pleasures when working with the Laguna Tools machine.

-4-www.igmtools.com
Loose sanding belt can cause injury. The workpiece may bounce o󰀨 the
sanding belt and turn against the machine operator.
Danger of thrown workpiece.
Dust and noise can be health hazards.
Be sure to wear safety goggles, ear protection and dust mask.
Use a suitable dust exhaust system.
Defective or damaged sanding belt can cause injury.
Do not use damaged or worn power cord.
3.4 Grounding Instructions
Connection cord:
In the case of a defect or malfunction, grounding provides a path of least
resistance to electric current, reducing the risk of electric shock. The
machine is supplied with connection cord with a guard wire and euro plug.
The plug must only be connected to an appropriate outlet in accordance
with all local codes and regulations.
• Do not modify the plug, if it does not t into the socket. Contact a
qualied electrician and have the appropriate socket installed.
• Improper connection may result in a risk of electric shock. Ground wire
is an insulated wire with a green surface with/without yellow stripes. If the
cord or plug needs to be repaired, contact a qualied electrician.
• Damaged cords should be repaired immediately and only by a qualied
electrician.
• Use only three-wire cables with a euro plug and an appropriate socket.
4. Machine Specication
Type: 1632
Power: 230 V / 50 Hz / 1 phase
Recommended circuit breaker: 16 A, rating C (16/1/C)
Current at maximum load: 6,5 A
Power output: 1100 W
Conveyor Belt Motor: 40 W
Speed: 1420 RPM
Feed Speed: 0-3 m/min.
Workpiece Width (one pass): 406 mm
Workpiece Width (two passes): 812 mm
Thickness of Material min. / max.: 0,8-76 mm
Drum Size: 127 x 406 mm
Width of Abrasive: 76 mm
Minimum dust collector capacities: 1000 m3/h
Dust Extraction Outlet: 100 mm
Length x width x height: 860 x 560 x 1220 mm
Weight: 62 kg
Shipping Dimensions: 940 x 660 x 550 mm
Shipping Weight: 71,7 kg
1. Height adjustment handle of the drum
2. Shroud
3. Digital Read-out
4. Knob to start feed conveyor and select feed rate
5. Starts and stops drum motor
6. Conveyor table
7. Tension roller contact adjustment
8. Drum carriage
5. Transport and Setup
5.1 Setup
The machine is transported in a shipping package. The machine is
designed to operate in closed rooms and must be placed stable on a
rm and levelled ground. The machine requires assembling.
Package contents
Stand box contents (found inside the main box)
Drum Sander Assembly
Note: For initial stand assembly secure all bolts nger tight. This will allow
for easier levelling after the sanding unit is installed on the stand. The
holes in the legs are spaced so that the short and long top braces will only
line up from one face of each leg.
1. Secure two legs to the outside of each of the two short top cross braces
using the supplied carriage bolts and ange nuts.
2. Secure the two long top rails inside of the legs and on top of the short
rails.

-5-www.igmtools.com
3. Note: Long rail on top of short rail and both rails inside of legs.
4. Connect the second leg sub-assembly to the top long rails.
5. Attach the lower cross braces to the legs. The longer cross braces
should sit on top of the short ones.
6. Attach a levelling foot to the bottom of each leg (not required if installing
optional caster set).
Note: After nal assembly and sander installation, adjust the nuts on the
threads as needed to level the stand.
IInstalling Drum Sander
1. For easier access to the machine, peel back the plastic liner, cut the
box at the corners, and fold down the 4 sides of the box.
2. Then with the help of an assistant carefully lift the machine and set it
down on a workbench with one end hanging slightly over the edge.
3. Unscrew the bolts holding the wooden packing support to the underside
of the machine, then carefully turn the machine around and repeat at the
opposite end (these bolts can be re-used to secure the unit to the stand;
extra bolts are also provided for this with the machine).
4. With the help of an assistant place the machine on the stand so that the
mounting holes on the stand line up with the holes on the underside of the
machine. Remove the Styrofoam and wooden support block from under
the sanding head.
5. Using the supplied 14 mm wrench bolt the machine to the stand from
underneath using the supplied hex bolts and washers.
Note: With the machine properly secured, level the stand and tighten all
its bolts.
LIFTING POINT
Drum carriage
LIFTING
POINT
Motor

-6-www.igmtools.com
16 A, rating C (16/1/C)). Do not plug the machine into the power supply
until it is fully setup.
6. Setting and Adjustment
6.1 Setting the Drum Sander
Checking Drum Alignment
UNPLUG THE MACHINE FROM THE POWER SOURCE!
During initial setup only. Checking the alignment is necessary to make
sure that the machine functions properly.
1. Before checking the drum alignment make sure that the fast lever
between the conveyor motor and the machine is in the up position
The conveyor table bolts on the inboard side should not be so tight that
the fast lever does not rotate – see rst note on page 17.
2. Remove abrasive from the drum. Removing the abrasive ensures that
the adjustment is as accurate as possible.
3. Use a at, uniform piece of wood as a thickness gauge. Set it between
the conveyor belt and the drum on the inboard (right) side of the machine.
4. The tension rollers are set just below the drum enough so that material
cannot pass easily underneath. Use the height adjustment handle to lower
the head until the drum makes contact with the piece of wood. Turn on the
DRO and take note of the thickness indicated on the display.
6. Screw the height adjustment knob into the handle and tighten it down.
7.+ 8. Slide the digital read-out (DRO) out and install the supplied batteries
with the (+) side facing up.
9. Slide the DRO fully back and plug in the cable from the machine.
Installing Drum Sander (continued)
10. Plug the short power cord that is attached to the motor into the outlet
on the control panel.
11. Make sure that your power supply is adequate (230 V, circuit breaker

-7-www.igmtools.com
5. Raise the head of the sander by rotating the height adjustment handle up
exactly one full turn.
6. After the height has been adjusted move the piece of wood over to the
outboard side (left) and lower the head by turning the handle down exactly
one full turn until the DRO thickness matches the noted thickness from
step #4.
7. Check the height of the drum in relation to the piece of wood. It the
drum is aligned it will just make contact with the wood as it did on the
inboard side. If you cannot turn the handle one full turn, or if there is a
gap between the drum and the wood, proceed to the following alignment
procedure
8. If the drum is not parallel, loosen the 4 socket head screws (A) along
the outboard (left) side of the conveyor belt and raise or lower the
conveyor with the adjustment nut (B) to achieve parallel alignment. Then
tighten the 4 socket head screws.
Connecting Dust Collection
Dust collection is necessary for the drum sander. The sander comes
equipped with a 100 mm (4”) diameter dust exhaust port at the top of
the cover. Make sure that the minimum dust requirements are su󰀩cient.
To attach to your collection system, install 100 mm (4”) hose from your
collector. The minimum recommended dust collector capacities is 1000
m³/h. For best results, follow the recommendations of the manufacturer
of your dust collector. When connecting dust collector straight pipe is
preferred because it is the least restrictive for airow. If straight pipe is not
possible Y’s and elbows are preferred because they are less restrictive to
airow than T’s.
Note: Some applications will require more dust collection than the
recommended minimum.
Power and Electrical Safety
11. Make sure that your power supply is adequate (230 V, circuit breaker
16 A, rating C (16/1/C))). After the dust collection system is in place and
the drum alignment is checked your machine is ready to be powered up
and operated.
Abrasive Selection Guide
To attach the abrasive to the drum, follow the procedure below.
Grit Common Application
36 GRIT - Abrasive planing, surfacing rough-sawn boards, maximum
stock or glue removal
60 GRIT - Surfacing and dimensioning boards, trueing warped boards
80 GRIT - Light dimensioning, removal of planer ripples
100 GRIT - Light surfacing, removal of planer ripples
120 GRIT - Light surfacing, minimal stock removal
150 GRIT - Finish sanding, minimal stock removal
180 - GRIT Finish sanding only, not for stock removal
220 GRIT - Finish sanding only, not for stock removal
6.2 Installing and Wrapping Abrasives
Accurate attachment of the abrasive to the drum is critical to achieving
the machine top performance. Abrasive strips do not have to be pre-
measured. The end of the roll is rst tapered and attached to the outboard
(left) side of the drum. Then the strip is wrapped around the drum. The
second taper is made for attachment to the inboard (right) side of the
drum.
Note: Pre-cut abrasives have been factory tapered to the specic width of
your drum. If you are cutting your own abrasive, use the wrap that came
on the drum as a template (abrasive side up).
Installing and Wrapping Abrasives (continued)
UNPLUG THE MACHINE FROM THE POWER SOURCE!
1. Start on the left (outboard) side of the drum. Squeeze the clip lever and
insert the tapered end of the paper into the fastener so that it uses most of
the width of the slot. Release the clip lever to securely hold the abrasive.
Drum width: 406 mm (16“)
Tip-to-tip: 2 463 mm (97“)
Abrasive ready to install: 2 311 mm (91“)
Approximately 76 mm (3“)
76 mm (3“)
400 mm (15-3/4“)
TAPERED END OF THE
ABRASIVE

-8-www.igmtools.com
2. Wind the abrasive around the drum, being careful not to overlap the
windings. The tapered cut of the wrap end should follow the edge of the
drum.
Continue to wrap the abrasive in a spiral fashion by rotating the drum with
your left hand and guiding the abrasive with your right hand. Successive
windings of the wrap should be ush with previous windings without any
overlap.
3. Squeeze the clip lever to open the clip and pull the take-up lever to the
top. Insert the tapered end through the slot in the inboard (right) end of the
drum.
4. The take-up fastener is designed to automatically tension the abrasive
wrap. If during use the abrasive wrap stretches enough to allow the take-
up lever to reach its lowest position and no longer maintain tension on the
wrap, see Abrasive Tension Adjustment.
Note: The drum was removed to show the inboard (right) take-up fastener.
7. Machine Operation
Proper Abrasive Position
Position the abrasive in the slot with su󰀩cient room between the inside
of the slot and the tapered end of the wrap to allow it to be pulled into the
drum as needed. If enough space is not left between the wrap and the
inside of the slot the take-up fastener will not operate properly.
Abrasive Tension Adjustment
The abrasive wrap may stretch enough to allow the take-up lever to reach
its lowest position. If this occurs, then the abrasive is no longer tensioned.
To x this reset the take-up lever by raising it. Push the abrasive into the
slot and then release the clip lever.
Maximizing Abrasive Longevity
We recommend a sandpaper cleaning stick to remove deposits and help
extend the life of the abrasive.
1. To use the cleaning stick, operate the sanding drum with the dust cover
open and dust collection on.
2. Hold the cleaning stick against the rotating drum and move it along the
drum surface.
3. Use a brush to remove any cleaning stick remnants before resuming
operation.
ALWAYS WEAR EYE PROTECTION WHILE PERFORMING ABRASIVE
CLEANING. TAKE ALL PRECAUTIONS TO AVOID ANY CONTACT WITH
HANDS OR CLOTHING.
Operating the Sander
Using the DRO
Specications
Resolution: Decimal = .005 in.
Fraction = 1/32 in.
Metric = 0.1 mm
Accuracy: Decimal = +/- .0025 in.
Fraction= +/- 1/500 in.
Metric = +/- .05 mm
Battery: 2 AAA (not included)
Functions: - Constant memory retains calibration even when
OFF
- Incremental measuring mode
- Absolute measuring mode
- Millimeter, Inch and Fraction readout
- Auto shut o󰀨

-9-www.igmtools.com
Button Reference and Use
It is helpful to familiarize these buttons and their purpose with the Wixey
DRO
Calibration
There are three typical variations of calibration. The rst variation (Type 1)
is for the DRO to show the sanded thickness of
the material. The second variation (Type 2) is to show how much stock is
being removed with each pass of the sander.
Another method (Type 3) to show the amount of material being removed
per pass without recalibrating the Type 1 setting.
Type 1 Calibration ABS:
Calibration for the DRO to show sanded thickness (Type 1). Calibration is
quick and easy and requires no extra measuring
device. Make sure the machine is turned OFF and power is disconnected!
1. Wrap the sanding drum with the desired grit abrasive.
2. Lower the sanding drum until it lightly touches the conveyor belt.
3. Turn “ON” the DRO.
4. Hold the “CAL” button 3 seconds until “0.00” appears.
Type 2 Calibration ABS:
Calibration for the DRO to show stock removed per sanding pass (Type
2). Calibration is quick and easy and requires no
extra measuring device. Make sure the machine is turned OFF and power
is disconnected after the rst step!
1. Sand a test piece of stock until it is at and uniform on both sides.
2. Turn the Sander OFF and disconnect power to sander.
3. Position the sanding drum (with abrasive still wrapped on drum) on the
test piece until the drum is lightly touching the test
piece.
4. Press and hold the “CAL” button for 3 seconds until “0.00” appears.
Type 3 Calibration INC:
This method allows saving the original calibration from Type 1 and
conrming the amount of material being removed per
pass.
1. Make one pass sanding your stock. Without changing the drum height
press the “ABS/INC” button to read “0.00”. This
changes the readout from “ABS” to “INC” and zero’s the readout on top of

-10-www.igmtools.com
the just sanded piece. Now the readout will show
the amount of stock removed per sanded pass in “INC” mode.
2. To change back to the original (Type 1) calibration press the “ABS/INC”
button to change back to “ABS” mode.
NOTE: When changing the abrasive wrap to a di󰀨erent grit the DRO must
be recalibrated for the change of drum
diameter with the new grit abrasive!
NOTE: When setting the depth of cut, never exceed the thickness of the
grit for stock removal.
Depth of Cut/Sanding
Determining the depth of cut is the most important operating procedure
decision. It may take some experimentation to determine the proper depth
of cut. We recommend practicing on a scrap of wood prior to sanding a
project.
TIP: With the sander turned OFF, place the stock to be sanded under the
drum (wrapped with abrasive of choice)
and lower the drum until the drum contacts the workpiece and the drum
can be rotated with hand pressure.
This is a good test for maximum stock removal as you are becoming
familiar with setting the sander for proper stock removal.
Drum Head Height Adjustments
The drum height can be adjusted using one of two methods determined by
the position of the height adjustment selector.
In the micro adjustment position turning the main height adjustment
handle controls the height of the drum. Clockwise for Up and counter
clockwise for Down.
Note: One full turn raises or lowers the head approximately 1,6 mm
(1/16”).
With the selector in the quick lever position the main handle is
disengaged. Quick large-scale adjustments of up to 76,2 mm (3”) can then
be made by pulling up or down on the Quick Lever.
Note: After completing height adjustments in quick lever mode always
return the selector back to micro adjustment mode.
Conveyor and Speed Rate
After the depth of cut has been determined, selecting the proper feed rate
is essential. For nish sanding the best nish is usually achieved with a
slow to moderate feed rate. Faster feed rates can be used as long as the
machine is not over-stressed.
When nish sanding with grits ner than 80, the best nish can usually be
obtained if INTELLISAND does not engage. If INTELLISAND does slow
the conveyor when nish sanding, it is best to make another sanding pass
without changing the thickness setting and sand again
Note: INTELLISAND will automatically adjust the conveyor feed rate if
an excess load is detected. This prevents excessive gouging, reduces
the risk of burning and protects the machine from overload or stalling.
The red light by the adjustment knob will come on when INTELLISAND is
operating. When the load is decreased, INTELLISAND will automatically
increase the feed rate to the pre-selected speed.
Stock Feeding Operation
Rest and hold the stock to be sanded on the conveyor table. Allow the
conveyor to carry the stock into the drum. Once the stock is halfway
through, reposition yourself to the outfeed side of the machine to control
the stock as it exits the unit.
Stock Feeding Maximum Performance
The versatility of this drum sander allows it to be used for a wide range of
tasks. Learning to use the multiple controls to make adjustments will allow
you to ne tune the machine for maximum results.
• Sanding stock wider than the drum
When sanding stock wider than the drum the fast lever will be very useful
(see picture). Wide stock requires extra space between the drum and the
conveyor on the outboard (left) edge. The extra space prevents ridge lines
from developing along the part that extends beyond the drum. Adjust the
fast lever 45 degrees from the vertical position to slightly shift the drum
position. Before sanding always test on a scrap piece. If a line or ridge is
still visible, make adjustments to the drum alignment. Always return the
lever to the upright position when wide stock sanding is completed.
Note: The fast lever raises the inboard side of the table .003. Upon rst
use, the conveyor table bolts may be set too tight at the factory for secure
shipping. In this case, loosen the bolts slightly. Never tighten the table
bolts all the way. Tighten the bolts enough to still allow the fast lever to be
moved.
• Sanding multiple pieces simultaneously
When sanding multiple pieces at once, make sure to stagger the pieces
across the width of the conveyor belt. This position provides better contact
with the tension rollers. It is best to only process pieces that are all of a
similar thickness. If there is a thickness di󰀨erence, the thinner pieces may
not come in contact with the tension rollers and may slip on the conveyor
belt.
• Sanding Imperfect or Tall Stock
To avoid bodily injury, take special care when sanding stock that is
twisted, bowed or otherwise varied in thickness from end to end. If
possible, support such stock as it is being sanded to keep it from slipping
or tipping. Use extra roller stand, assistance from another person, or
hand pressure on the stock to minimize potentially hazardous situations.
Special attention is needed as the stock exits the machine. Special
attention is needed as the stock exits the machine.
• Stock Feeding Position and Angle
Positioning the stock at an angle will allow the most e󰀨ective stock
removal and least loading on the abrasives. Feeding stock straight
through yields the widest sanding capacity and least noticeable scratch
pattern. Some pieces because of their dimensions will need to be fed into
the sander at a 90-degree angle (perpendicular to the drum). However,
even a slight o󰀨set angle of the stock can provide for more e󰀨ective
sanding. Final pass sanding should be done while following the grain
pattern.
Tension Roller Pressure
The tension roller pressure is factory set and should be adequate.
However, the pressure of each roller can be adjusted as needed. To
increase the tension, turn the tension adjusting screw clockwise 1/4
revolution at a time. To decrease tension, turn the adjusting screw counter
clockwise 1/4 revolution at a time.
Note: Too little pressure can result in slippage of stock on conveyor belt or
kick-back Too much tension can cause snipe when drum sanding.

-11-www.igmtools.com
Tension Roller Contact Adjustment
The tension rollers are factory set for the most versatile use.
1. To adjust tension roller contact, loosen the four socket head screws
holding the tension roller brackets (2 per side; front and back).
2. Have abrasive wrapped on the drum.
3. With the machine unplugged, lower sanding drum until it rests on
conveyor belt.
4. Raise drum 2 to 3 revolutions.
5. Tighten the four socket head screws.
6. Raise the drum up, o󰀨 of the conveyor belt.
7. Set the drum on the proper sanding height.
Conveyor Belt Tension
Insu󰀩cient belt tension will cause slippage of conveyor belt on the drive
roller. The conveyor belt is too loose if it can be stopped by placing your
hand directly on the conveyor belt.
Excessive belt tension can result in bent rollers, premature wearing of the
bronze bushings or conveyor belt.
To adjust the conveyor belt, rst adjust the take-up screw nut on both
sides of the conveyor to obtain approximately equal tension on both sides.
Conveyor Belt Tracking
Belt tracking adjustments are made while the conveyor belt is running.
After the proper belt tension is obtained, turn the conveyor on and set it at
the fastest speed setting. Watch for a tendency of the conveyor belt to drift
to one side of the conveyor.
To adjust the belt tracking, tighten the take-up screw nut on the side the
belt is drifting toward, and loosen the take-up screw nut on the opposite
side.
Adjusting the take-up screw nuts does not a󰀨ect the belt tension.
Note: Adjust the take-up screw nuts only 1/4 turn at a time. Allow the
belt to react to the adjustments before proceeding further. Avoid over-
adjustments.
8. Maintenance
Monthly Maintenance
• Lubricate conveyor bushings and check for wear.
• Lubricate with a dry lubricant spray all of the moving parts.
• Clean dust from conveyor belt.
• Check all set screws for tightness.
• Clean drum and abrasives if necessary.
Replacing Conveyor Belt
To replace the conveyor belt, the conveyor assembly must be removed
from the machine.
Unplug the machine from the power source!
1. Raise the drum carriage to its highest position. Unplug main drive motor
from receptacle on the machine.
2. Loosen the conveyor take-up screws to relieve belt tension and slide
the drive roller fully inward.
3. Remove the two hex bolts on the inboard (right) side that attach the
conveyor assembly to the base.

-12-www.igmtools.com
TROUBLESHOOTING GUIDE: MOTOR
Problem Possible Cause Solution
Motor does not start
Main power cord unplugged from receptacle Plug in primary power cord
Drum motor cord unplugged from receptacle
near powerfeed motor
Plug in drum motor cord to receptacle on the
machine
Circuit fuse blown or circuit breaker tripped Replace fuse or retrip breaker (after determining
cause)
Brush motor overloads Inadequate circuit Check electrical requirements
Machine overloaded Use slower feed rate; reduce depth of cut
Conveyor motor oscillates
Motor not properly aligned Loosen housing bolts and hex screw holding
the coupler to drive roller
Shaft collar or bushing worn Replace shaft collar or bushing
Drive roller bent Replace drive roller
Drum motor or Conveyor gear motor stalls Excessive depth of cut Reduce depth of cut; reduce feed rate
TROUBLESHOOTING GUIDE: CONVEYOR
Problem Possible Cause Solution
Conveyor drive rollers run intermittently Shaft coupling loose Align shaft ats of gear motor and drive roller;
tighten shaft coupling set screws
Conveyor belt slips on drive roller Improper conveyor belt tension Adjust belt tension
Excessive depth of cut Reduce depth of cut; reduce feed rate
Stock slips on conveyor belt causing gou-
ging
Excessive depth of cut Reduce depth of cut Tension rollers too high Lower tension rollers
Excessive feed rate Reduce feed rate
Dirty or worn conveyor belt Clean or replace conveyor belt
Conveyor motor stalls
Belt out of adjustment Readjust belt
Roller bushings elongated due to excessive
wear Replace bushings
4. Remove the two nuts and washers from outboard (left) side. Lift
the conveyor and remove it from the sander. Set conveyor on motor
side. Avoid tearing the belt on any edges underneath the conveyor
bed during removal. Reverse the procedure for re-installation.
Cleaning the Sander
The sander may need to be cleaned more frequently depending
upon frequency of use. The drum and the conveyor belt need to be
clean. Allowing excess build-up of dust and debris can adversely
a󰀨ect performance and increase the likelihood of slippage on the
conveyor belt. Sweep the conveyor belt clean after all operations.
When cleaning dust from the drum leave the dust collection system
on.
Optional Accessories:
IGM Fachmann Stick Abrasive Cleaner
Order code: MCBP
IGM LAGUNA 1632 Drum Sander Folding Infeed/Outfeed Tables
Order code: 151-1632FT
Conveyor Belt
IGM LAGUNA Conveyor Belt for Sander 1632 SuperMax
Order code: 151-1632-015
Abrasives
Up to date o󰀨er at www.igmtools.com
9. Troubleshooting
Any operating problems will likely occur during the period of
becoming familiar with the sander. If you are experiencing a problem
a󰀨ecting the machine’s performance, check the following listings for
potential causes and solutions. Also review the previous sections in
this manual on setting up and operating your machine.

-13-www.igmtools.com
TROUBLESHOOTING GUIDE: MACHINE
Problem Possible Cause Solution
Drum height adjustment works improperly Improper adjustment of height control Readjust height control
Knocking sound while running Bearing worn Replace the bearing.
Contact distributor
Sniping of wood (gouging near end of
board)
Inadequate support of stock Use roller stands to support stock
Conveyor drive or driven rollers higher than
conveyor bed Readjust rollers
Exessive tension roller pressure Adjust rollers
Burning of wood or melting of nish Feed rate too slow Increase feed rate
Excessive depth of cut Reduce depth of cut
Conveyor motor stalls
Conveyor belt is too loose Adjust belt tension
Excessive depth of cut Reduce depth of cut
Wood slipping on conveyor due to lack of
contact Use alternate feeding procedure

-14-www.igmtools.com
16-32 - HEAD ASSEMBLY

-15-www.igmtools.com
# PART NO DESCRIPTION SIZE QTY
Key Part Number Description Specication Qty
1 71632-101 Motor 1
2 480BS-102 Strain Relief, motor 7P-2 3
3 71632-103 Main Cord, Inverter to Control Box 1
4 480BS-104 Key 3/16"SQx3/4" 2
5 480BS-105 Nylon Insert Lock Nut 5/16"-24 4
6 480BS-106 Flat Washer 5/16" 8
7 480BS-107 Oilite Washer 5/16" 8
8 71632-108 Motor Plate 1
9 71632-109 Nut 1
10 71632-110 Hex Cap Screw 5/16"-18x1" 4
11 480BS-111 Lock Washer 3/8" 4
12 71632-112 Socket Head Cap Screw 3/8"-16x3/4" 4
13 480BS-113 Set Screw 1/4"-20x1/4" 5
14 480BS-114 Coupling 2
15 480BS-115 Coupling Spider 1
17 480BS-117 Screw, Phil Pan Head M4x0.7x6 5
18 71632-118 Screw M3x0.5x8 1
19 71632-119 Micro Adjustment/Quick Knob 1
20 480BS-120 Knob 1
21 480BS-121 Height Adjustment Handle 1
22 480BS-122 Nylon Insert Lock Nut 5/8"-11 1
23 71632-123 Height Adjustment Screw 1
24 71632-124 Washer, Wave D17 1
25 480BS-125 Thrust Bearing 51103 1
26 71632-126 Shroud 1
27 30-3028 Stud 4
28 71632-128 Hex Cap Screw 3/8"-16x3/4" 8
29 480BS-129 Flat Washer 3/8" 8
30 480BS-130 Hinge 2
31 71632-131 Dust Cover 1
32 480BS-132 Handle 1
33 480BS-133 Pan Head Machine Screw #8x1/2" 4
34 480DS-134 Lock Washer M3 2
35 480BS-135 Dust Cover Latch 1
36 480DS-136 Phillips Flat Head Screw M3x0.5x10 2
37 71632-137 Sanding Drum 1
38 480DS-138 Hex Nut M3x0.5 2
39 480DS-139 Inboard Abrasive Fastener 1
40 480DS-140 Outboard Abrasive Fastener 1
41 71632-141 Carriage Bolt 5/16"-18x3/4" 4
42 480DS-142 Bearing 6205LLU 2
43 480DS-143 C-Ring S25 2
44 71632-144 Drum Carriage 1
45 480BS-145 Flat Washer 1/4" 5
46 71632-146 Round Socket Head Cap Screw 1/4"-20x3/4" 4
47 480BS-147 Flat Washer 5/16" 4
48 480DS-148 Bearing Seat 2
49 480BS-149 Hex Cap Screw w/ Washer #10-24x3/8" 2
50 480BS-150 Dust Cover Catch 1
51 480BS-151 Stud 1
52 480BS-152 Spring 1
53 71632-153 Tension Roller 2
54 480BS-154 Bushing, Oilite 4
55 480BS-180 Tension Roller Bracket, Outer
Left 2
56 480BS-156 Screw 5/32"-32x1" 4
57 480BS-157 Spring, Tension Roller 4
58 480BS-179 Tension Roller Bracket, Outer
Right 2
59 480BS-159 Pad, Bracket-Tension Roller 2
60 71632-160 Bracket 2
61 480BS-161 Plate 1
62 71632-162 Base 1
63 480BS-163 Adjusting Lever (FAST) 1
64 480BS-164 Adjusting Rod 1
65 480BS-165 Height Adjusting Plate 1
66 71632-166 Round Socket Head Cap Screw 5/16"-18x3/4" 4
67 480BS-167 Lock Washer 5/16" 4
68 480BS-168 Spring 3
69 480BS-169 Nylon Insert Lock Nut 1/4"-20 1
70 71632-170 Socket Head Cap Screw 5/16"-18x1-1/2" 2
71 480DS-171 Hex Nut w/ Washer 5/16" 4
72 71632-172 Spring 1
73 71632-173 Quick Arm 1
74 71632-174 Rubber Sleeve 1
75 71632-175 Cap 1
76 71632-176 Micro Adjustment/Quick Bar 1
77 71632-177 Screw, Phil Pan Head M4x0.7x10 4
78 71632-178 Cylinder 1
79 71632-179 Quick Arm Handle 1
80 71632-180 Spacer 1
81 480BS-181 E-Ring E5 1
82 71632-182 Nut 1
83 71632-183 Socket Head Cap Screw M6x1.0x30 1
84 71632-184 Socket Head Cap Screw M6x1.0x15 1
85 71632-185 Micro Adjustment/Quick Label 1
86 480BS-186 Maintenance Label 1
87 480BS-187 Warning Label 1
88 71632-188 Set Screw 1/4"-20x3/8" 1
89 71632-189 O-Ring P8 1
90 71632-190 Screw M5x0.8x12 3
91 71632-191 Cover, Base-Control Box 1
92 71632-192 Switch, ON/OFF 1
93 480DS-210 Controller 1
94 480BS-207 Knob 1
95 71632-195 Speed Adjustment Label 1
96 480DS-213 Receptacle, Main Cord 1
97 480DS-203 Power Cord 1
98 71632-198 Pan Head Self-Tapping Screw M3x0.5x10 2
99 480BS-214 Screw #10-32x1/2" 2
100 480BS-215 Washer, Lock-Int. Tooth #10 2
101 480BS-204 Flat Washer 5/16" 1
102 480BS-242 Hex Nut 5/16"-24 1
103 480BS-243 Slotted Set Screw #8-36x5/16" 1
104 71632-1104 Hex Nut M4x0.7 4
105 71632-1105 Hex Nut #10-32 2
106 71632-1106 Cover, Base-Control Housing 1
109 72550-197 Screw, Phil Pan Head M4x0.7x12 2
111 71632-1111 Abrasive #80 1
112 71632-1112 Nylon Washer M3 2
117 71632-1117 Socket Head Cap Screw 5/16"-18x1-3/4" 1
121 71632-1121 Flat Washer M3 1
122 71632-1122 Tool Storage 1
123 71632-1123 Fixed Plate, DRO 1
124 71632-1124 Wixey Digital Readout (AAA
Batteries not included) 1
# PART NO DESCRIPTION SIZE QTY

-16-www.igmtools.com
# PART NO DESCRIPTION SIZE QTY
1 480BS-501 LEG, LEFT 2
2 480BS-502 LEG, RIGHT (WITH TOOL
HOLDER) 2
3 71632-303 TOP CROSS BRACE, LONG 2
4 71632-304 TOP CROSS BRACE, SHORT 2
5 71632-305 LOWER CROSS BRACE
RAIL, LONG 2
6 71632-306 LOWER CROSS BRACE
RAIL, SHORT 2
7 480BS-507 FLANGE NUT 5/16" 8
8 480BS-508 LEVELING FOOT 4
9 480BS-129 FLAT WASHER 3/8" 8
10 480BS-509 HEX NUT 3/8"-16 8
11 480BS-506 CARRIAGE BOLT 5/16"-18 X 5/8" 24
BLUE
BLUE
BLUE
BLUE
BLUE
16-32 - WIRING DIAGRAM
16-32 - OPEN STAND ASSEMBLY

-17-www.igmtools.com
# PART NO DESCRIPTION SIZE QTY
1 71632-201 CONVEYOR MOTOR 90 VDC 1
2 480BS-204 FLAT WASHER 5/16" 4
3 480BS-205 SOCKET HEAD CAP SCREW #10-32 X 1/2" 4
4 480BS-206 TRACKER KIT 2
5 71632-205 MOTOR MOUNTING PLATE 1
6 480BS-113 SET SCREW 1/4"-20 X 1/4" 2
7 480BS-224 HEX CAP SCREW 1/4"-20 X 3/4" 5
8 480BS-154 OILITE BUSHING 3
9 71632-209 ROLLER, DRIVEN 1
10 480BS-167 LOCK WASHER 5/16" 4
11 71632-211 ROLLER, DRIVE 1
12 480BS-237 DRIVE ROLLER SUPPORT BRACKET 1
13 71632-213 CONVEYOR BED 1
14 480BS-239 SOCKET HEAD CAP SCREW 1/4"-20 X 3/4" 4
15 71632-215 CONVEYOR BELT (NOT SHOWN) 1
16 480BS-245 HEX NUT 5/16"-18 2
17 71632-217 FLAT HEAD PHILLIPS SCREW 1/4"-20 X 3/4" 1
18 480BS-227 TAKE UP SLIDE BRACKET 2
19 480BS-234 TAKE UP BASE BRACKET 2
20 480BS-225 WAVE WASHER 1/4" 4
21 480BS-145 FLAT WASHER 1/4" 2
22 480BS-233 ROUND HEAD SLOTTED SCREW 1/4"-20 X 1-3/4" 2
23 480BS-232 INT. TOOTH LOCK WASHER 1/4" 2
24 480BS-230 WRENCH 2
25 480BS-231 HEX NUT 1/4"-20 2
26 480BS-247 HEX CAP SCREW W/ WASHER 1/4"-20X1/2" 6
# ....... PART NO. ............. DESCRIPTION.....................................................SIZE .................................................. QTY
1 ........71632-201 ................CONVEYOR MOTOR .........................................................90 VDC ................................................................ 1
2 ........480BS-204 ................ FLAT WASHER ...................................................................5/16" .................................................................... 4
3 ........480BS-205 ................ SOCKET HEAD CAP SCREW ........................................... #10-32 X 1/2" ..................................................... 4
4 ........480BS-206 ................TRACKER KIT .................................................................................................................................................... 2
5 ........71632-205 ................ MOTOR MOUNTING PLATE ........................................................................................................................... 1
6 ........480BS-113 ................ SET SCREW ........................................................................1/4"-20 X 1/4" ..................................................... 2
7 ........480BS-224 ................ HEX CAP SCREW ...............................................................1/4"-20 X 3/4" ..................................................... 5
8 ........480BS-154 ................OILITE BUSHING ............................................................................................................................................... 3
9 ........71632-209 ................ROLLER, DRIVEN ............................................................................................................................................... 1
10 ......480BS-167 ................ LOCK WASHER ..................................................................5/16" .................................................................... 4
11 ......71632-211 ................ROLLER, DRIVE .................................................................................................................................................. 1
12 ......480BS-237 ................DRIVE ROLLER SUPPORT BRACKET ............................................................................................................ 1
13 ......71632-213 ................CONVEYOR BED ............................................................................................................................................... 1
14 ......480BS-239 ................ SOCKET HEAD CAP SCREW ...........................................1/4"-20 X 3/4" ..................................................... 4
15 ......71632-215 ................CONVEYOR BELT (NOT SHOWN) .................................................................................................................. 1
16 ......480BS-245 ................ HEX NUT .............................................................................5/16"-18 .............................................................. 2
17 ......71632-217 ................ FLAT HEAD PHILLIPS SCREW ........................................1/4"-20 X 3/4" ..................................................... 1
18 ......480BS-227 ................ TAKE UP SLIDE BRACKET .............................................................................................................................. 2
19 ......480BS-234 ................ TAKE UP BASE BRACKET ............................................................................................................................... 2
20 ......480BS-225 ................ WAVE WASHER .................................................................1/4"....................................................................... 4
21 ......480BS-145 ................ FLAT WASHER ...................................................................1/4"....................................................................... 2
22 ......480BS-233
................ROUND HEADSLOTTED SCREW ..................................1/4"-20 X 1-3/4" ................................................. 2
23 ......480BS-232 ................ INT. TOOTH LOCK WASHER ............................................1/4"....................................................................... 2
24 ......480BS-230 ................ WRENCH ............................................................................................................................................................ 2
25 ......480BS-231 ................ HEX NUT .............................................................................1/4"-20 ................................................................. 2
26 ......480BS-247 ................ HEX CAP SCREW W/ WASHER ......................................1/4"-20X1/2" ....................................................... 6
16-32 - CONVEYOR AND MOTOR
16-32 - CONVEYOR AND MOTOR

IGM nástroje a stroje s.r.o., Ke Kopanině 560,
Tuchoměřice, 252 67, Czech Republic, EU
[phone],www.igmtools.com
© 2022 IGM nástroje a stroje s.r.o.