landscape structures Hang Glider 156465 User manual

© 2012 by Landscape Structures.All rights reserved.
601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 [phone] 1-888-LSI-INST (1-888-574-4678) FAX [phone]
Document #18496100
156465 Hang Glider®
Evos
®
DETAIL
CROSSOVERATTACHMENT
(2) 5" Clamp
Assemblies
Ref. To Plan
View
(2) Ball
Retainers
(2) Ball
Clamps
(4) 3/8" x 1 1/8
BHCS w/Pin
(4) 5/8" x 1 1/2
BHCS w/Pin
#100201-00
(Orange Patch)
(2) 5" Clamp
Assemblies
Ref. To Plan View
(2) 1/4" x 3/8"
Drive Rivets
Protective
Surfacing
Arch #3
Arch
(2) Hang
Glider Rails
Crossover
DETAIL
Crossover
Curved Loop
Pole
Curved Loop
Pole
Crossover
(2) Hang
Glider Rails
(4) 1/4" x 3/8"
Drive Rivets Arch
Hang Glider
Crossover Stubs
10" Inside
254
Arch #4
18496100
Sheet 1 of 2
SAFETY NOTE
Choose a protective surfacing material that
has a Critical Height Value of at least the
height of the Highest Accessible Part/Fall
Heightoftheadjacentequipment. (Ref.ASTM
F1487.)

Specifications are subject to change without notice.
Evos®156465 Hang Glider®
J:\INSTSPEC\SPECS\184\18496100.P65
Parts List
Part# Description Qty.
154800-00 Hang Glider Rail, Specify Color .............................. 2
182712-00 Hang Glider Crossover, Specify Color .................... 1
182643-00 Curved Loop Pole, Specify Color ............................ 1
156699-00 Ball Clamp, Specify Color........................................ 2
156700-00 Ball Retainer, Specify Color..................................... 2
182368-00 Hang Glider Hardware Package........................... 1
100198-00 3/8" x 1 1/8" BHCS w/Pin, SST .................................. 4
100201-00 5/8" x 1 1/2" BHCS w/Pin, SST .................................. 4
100611-00 1/4" x 3/8" Drive Rivet, AL/SST ................................. 6
156848-00 Play It Safe Label, 8-12 Years .................................. 1
Specifications
Hang Glider Rail: Fabricatedfrom1.900"O.D. RS40 (.120"-.130" wall)
galvanized steel tubing. Finish: ProShield®, color
specified.
Curved Loop Pole: Weldment comprised of 2.375" O.D. RS20 (.095"-
.105" wall) galvanized steel tubing, and 1.029" O.D.
RS20 (.070"-.080" wall) galvanized steel tubing. Fin-
ish: ProShield, color specified.
Crossover: Weldment comprised of 1.315" O.D. RS20 (.080"-
.090"wall)galvanizedsteeltubing, 1.900" O.D. RS20
(.090"-.100"wall) galvanized steeltubing,2.375" O.D.
RS40 (.130"-.140" wall) galvanized steel tubing, 1/8"
HRPO sheet steel and 1 7/8" steel ball. Finish:
ProShield, color specified.
Ball Clamp/
Ball Retainer: Cast from 535 almag. Finish: ProShield, color speci-
fied.
Fasteners: Primary fasteners shall be socketed and pinned
tamperproofindesign, stainless steel(SST)perASTM
F 879 unless otherwise indicated (see specific prod-
uct installation/specifications).
InstallationTime: Approx. 3 man hours
Concrete Req.: Approx. 3.75 cu. ft.
Area Req.: 6' (1830 mm) minimum use zone
Weight: 162 lbs.
Fall Height: 81" (2060 mm)
Installation Instructions
1) (Direct Bury) Refer to the Site Plan for footing locations.
2) Attach ball retainers to 5" round clamps using 5/8" x 1 1/2" BHCS w/pin.
Attach crossover to ball retainers using ball clamps and 3/8" x 1 1/8"
BHCS w/pin. Refer to the Crossover Attachment Detail. NOTE: 5"
Round clamps may need to be turned, or moved up or down to con-
nect crossover and position hang glider properly. Check to make
sure crossover is level, if not adjust 5" round clamps.
3) Insert end of curved loop pole into crossover stub. With curved loop
pole steps level, drill through holes in crossover tube into curved
loop pole with a 1/4" or "F" (only) drill bit. Insert 1/4" x 3/8" rivets into
holes and hammer rivet pins in until it is flush with head. Refer to
Detail. NOTE: Distance from center rail of loop pole to arch should
be greater than 9".
4) Place hang glider rails onto crossover stubs. With glider rails in proper
position, drill through holes in hang glider rails into crossover with a
1/4" or "F" (only) drill bit. Insert 1/4" x 3/8" rivets into holes and ham-
mer rivet pins in until it is flush with head. Refer to Detail.
5) With curved loop pole steps and crossover level and rail hang glider
in proper position, pour concrete footings. Allow concrete footings
to cure for a minimum of 72 hours before users are allowed to play
on the structure.
6) Install protective surfacing before users are allowed to play on the
structure.
Eco #54543 Document 18496100 replaces 18282900. Changed curved loop pole part number.

© 2012 by Landscape Structures.All rights reserved.
601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 [phone] 1-888-LSI-INST (1-888-574-4678) FAX [phone]
Document #18496100
Sheet 2 of 2
184961a
DETAIL
DIRECT BURY
Loose Fill
Protective
Surfacing
Subgrade
Concrete
Crushed Rock
12"
305
20" Min 508 34"
864
Hang Glider Rails &
Curved Loop Pole
Proper Use Label
(Affixed At Factory)
NOTE: Distance from
center rail of loop pole
to arch should be
greaterthan 9".
SAFETY NOTE
Choose a protective surfacing material that
has a Critical Height Value of at least the
height of the Highest Accessible Part/Fall
Heightof theadjacentequipment. (Ref.ASTM
F1487.)
Play It Safe Label
156465 Hang Glider®
Evos
®
NOTE: Attach Play It
Safe Label 8-12 Years,
approximately as
shown.