Lassic Casa Vida PANAMA SIDEBOARD User manual

IMPORTANT
READ THESE INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR USING
YOUR PANAMA SIDEBOARD.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ASSEMBLY INSTRUCTIONS
PANAMA SIDEBOARD
www.lassic.co.uk
4 m
4m
CARE & MAINTENANCE:
Assemble in the room of use.
To avoid damages assemble the item on a soft, clean surface
Periodically check all screws & fixings to ensure they are secure.
DO NOT push the item as this will damage the base.
Always lift the item with two people to reposition.
Keep any sharp objects away from the item.
This product is manufactured in pine which is a wood with natural characteristics including knots, grains,
clusters or indentations.
On unpacking the item you may notice an odour due to production processes but this will disappear after a
period of time.
DO NOT place the item next to a radiator or direct sunlight – this item is susceptible to temperature change.
It is recommended an even room temperature be maintained with no sudden fluctuations.
DO NOT place hot or cold items directly onto the surface of the item as marking will occur
For general cleaning use a duster or damp cloth (almost dry) not wet – do not use soap and water,
detergents, aerosol sprays or any polish as use of these materials would invalidate any claims.
DO NOT place the item onto wet or damp flooring as staining may occur to the floor.
HEALTH & SAFETY:
DO NOT use this item if any parts are missing, damaged or worn.
DO NOT use this item unless all fixings are secured.
Please keep small parts out of reach of children.
Always use on a level, even surface.
It is recommended that two people handle and assemble the item.
Page 1 of 12
800mm
930mm
405mm

Page 2 of 12
1
2
3
4
5
6
7
8
910
11
12
13
15
16
17
18
19
20
21
22
23
14
16
10
6
2x
14

Wooden dowel
14mm Screw
35mm Screw
Shelf Support
19mm Bolt
A
D
B
E
C
H
25
26
8
4
4
30mm Screw
31
Handle
Tack
G
F
4
36
Clip
Plug
Door Hinge
Corner bracket
4
2
2
1
L
K
J
M
N
16
30mm Screw
Page 3 of 12
HARDWARE LIST
PARTS LIST
Part Item Qty Part Item Qty
Vertical Frame
11 Top Panel
Right Panel
Left Panel
Base Panel
Shelf panel
12
1
3
1
4
1
5
2
6
1
7
1
8
1
9
2
10
111
Back column
Cross Rail
Side Drawer Runner
1
Small Vertical Frame
Middle Drawer Runner
Drawer Side
Drawer Front
Drawer Base
Drawer Back
1
2
4
2
2
2
1
1
221
222
18
19
20
15
16
17
12
13
14
Back panel
Spine
Door
Cleat 4
23
Right Front Frame
Left Front Frame
Centre Front Frame
Front Frame
You will need a small mallet and a screwdriver.
Recycle
2m
01 2 345 6 7891 0
mm 1 1 1 2 1 3 1 4 1 5 1 6

Step 2: Insert the left panel (3) to the left front frame (5) making sure the parts are
pushed together and lined up. Place the cleats (15) between the marks shown and
secure using hardware part D and a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
23
Attention: correct
position of panel.
Top
23
3
9
Yes!No!
3
9
E
E
23
Step 1: Insert the right panel (2) to the right front frame (8) making sure the parts are
pushed together and lined up. Place the cleats (23) between the marks shown and
secure using hardware part D and a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
2
Yes!No!
2
8
8
23
23
Attention: correct
position of panel.
Top
E
E
23
Page 4 of 12

Step 4: Connect the back column (20) to the middle drawer runner (19) using hardware part E and a screwdriver
(not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
19
20
E
Page 5 of 12
Step 3: Insert hardware part A using a small mallet (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim
2and L
L
L
3
A
A
A
A
AA
A
A
A
2x
4
19
20
22
A

Step 5: Connect the front frames (10) and centre front frame (11) to the small vertical frame (12) and
vertical frame (13).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 6: Attach the left panel (3) to the front frame section.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
10
11
12
13
10
74mm
90mm
12
3
Page 6 of 12

Step 7: Attach the base panel (4) using hardware part E and a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 8: Attach the right panel (2) using hardware part E, then attach hardware part M using hardware part B.
You will need to use a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
4
3
E
E
Attention:
4
2M
B
B
M
E
E
Page 7 of 12

Step 9: Attach the top panel (1) using hardware part E and a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
E
E
1
E
E
E
E
E
E
22
22
19
Step 10: Attach the side drawer runners (22), back column (20) and middle drawer runner (19) using hardware
part E and a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Page 8 of 12

Step 13: Attach the doors using hardware part B and a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 11: Attach the cross rails (21) to the doors (14) using hardware part D. Attach hardware
part H to the doors using hardware part B. You will need to use a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
H
B
View from behind
B
Step 12: Attach hardware part G to the doors (14) using hardware part F and a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
14
14
H
H
D
D
21
14
2x
14
2x
F
F
G
G
Page 9 of 12

Step 14: Attach hardware part J to the base panel (4) using hardware part B. Insert hardware
part K and push the doors shut against them to mark the wood. Secure hardware part K to the
doors (14) using hardware part B. You will need to use a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
a:
b: d:
c:
B
B
5
Step 15: Insert the shelf panel (5).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
4
14
14
K
J
J
K
4
J
J
J
KK
14 14
Page 10 of 12

Step 17: Assemble the drawer components using hardware parts C, F and G with a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
a: b:
c: d:
2x
C
C
C
C
G
F
15
16
16
17
18
Step 16: Join together the back panels (6) with the spine (7) and attach to the frame using
hardware part N and a small mallet (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
7
6 6
7
6
6
N
N
N
N
Page 11 of 12

Step 18: Insert the assembled drawers and secure using hardware part A and a small mallet
(not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
A A
Page 12 of 12
Additional Information
If you have any issues with your item please contact the retailer directly you
purchased it from who will be able to resolve any issues.