Learn & Climb STAY IN BED User manual

1
USER MANUAL
STAY IN BED
L I G H T C L O C K

2
ALARM SETTINGS pg. 7, 8, 9
ADVICE AND SAFETY pg. 10, 11
ABOUT
The Stay in bed clock, is a fun clock that can help kids learn about
time and helps parents get more time to sleep! The Stay in Bed
clock, can also be a Night-light, when your little one is sleeping.
You will nd the Stay in Bed clock useful for kids to learn time and
wake up at the right time!
SAFETY INSTRUCTIONS pg. 3
VISUAL GUIDE pg. 3
WHAT'S INCLUDED pg. 4
SETUP pg. 4
SETTING THE TIME FORMAT AND TIME pg. 5
NIGHT LIGHT SETTING pg. 6
AUTO OFF FUNCTION pg. 6

3
SAFETY INSTRUCTIONS
VISUAL GUIDE
Please read these safety instructions completely before using this product
for your protection.
• For safety reasons, all warnings and operating should be followed and adhered to.
• All packing materials, such as tape, plastic, sheets, packaging locks, wire ties and tags
are not part of this toy, and should be discarded for your child’s safety.
• Please keep this user’s manual as it contains important information.
• Please protect the environment by not disposing of this product with household waste.
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may
cause undesired operation.

4
WHAT'S INCLUDED IN THIS PACKAGE
SETUP
• 1 Stay in Bed Light Clock
• 1 USB Power Cable (USB Power Supply not included)
The supplied USB Power Cable can be used with any USB Power Supply.
This Clock can be powered with either the USB Cable or 3 AA batteries (batteries are not
included).
USING BATTERIES
1. Locate the battery cover on the bottom of the unit and open
it with a small Philips screwdriver.
2. Insert 3 AA batteries as illustrated
3. Replace the battery cover and tighten the screw
USING THE USB POWER CABLE
1. Take the supplied USB Power cord and plug it into the Power port on the back of the
clock.
2. Insert the other end of the USB Power Cable into a USB Power Supply (not included),
and then insert into a regular 120V Outlet.
Once the batteries are inserted or the clock is plugged into an outlet the Clock will
beep and the screen will display “12:00 AM”. At this time you can set the time.

5
SETTING THE TIME FORMAT AND TIME
SETTING THE TIME FORMAT
Open the rear control panel compartment (See Image 1)
SETTING THE TIME
1. (1) Hold down the “Set Time” button for 2 seconds.
The Setting icon “ ” will start flashing and “12Hr” will be
displayed on the screen. See Image 2.
2. Push the “Hour” button to choose the clock format
between 12 Hr. and 24 Hr.
3. After choosing the hour format push the “set time”
button to save the format setting. After selecting your
hour format the display will look like “Image. 3” and you
can now set the clock Time.
4. Push the “Hour” & “Min” buttons to adjust the time.
5. Once you are done adjusting the time, push the “set
time” button to save the time setting. Screen display
will look like “image 4”

6
NIGHT LIGHT AND LIGHT BRIGHTNESS
SETTING THE AUTO-OFF FUNCTION
• When the clock is in regular time dislay mode the night light
can be turned on by pushing the “big Light button” on the left
side. (See Image 5)
• The Clock has 4 light colors to choose from (Orange, Green,
Red, Purple) that can be cycled through using the light bulb
button on the left side.
• When any of the clock light colors are on, the brightness can
be adjusted by pressing the “Light Adj.” button in the control
panel. There 3 different brightness settings.
• The Night Light will stay on all Night unless the auto-off option
is programmed. (see programming Auto-off Function)
The Auto-off function will turn off the night light in between 15 minutes and 2 hours in 15
minute increments.
SETTING THE AUTO OFF
• Hold Down the Auto Off button for 2 seconds. The “ icon” will flash and “Off” will be
displayed on the screen.
• By default, the Auto-Off Function is off and the night light will stay on all night.
• Push the “Min” buttons to select the length of time (in 15 min increments) that you want
the night light to stay on, before turning off.
• Once the amount of time for the auto-off function is displayed, push the “auto-off” button
to save the settings.
• The setting is now locked and the display will show the current time.
Note: The light have the brightness adjusted with the “light adj.” after you
push the“big Light button” to light on. The brightness can not be adjust during
programming and when the alarm time displaying at the top of the screen.
Note: Auto-Off does not get saved for each night light use. Every time you
turn on the Night Light and want it to shut at a designated time, you will need
to reset Auto-Off.

7
ALARM SETTINGS
SETTING THE OK TO COME OUT OF BED LIGHT/ALARM
1. Hold down the alarm button for 2 seconds. The icon and will start
flashing. See Image 6.
2. Push the “Hour & Min” buttons to set the alarm time.
3. Once the alarm time has been set, push the “Alarm” button to continue on
to the ringer selection.
4. Push the big on the right side of the clock repeatedly to select the type of ringer for
the alarm. This clock has 3 ring types: No ring, Slow Ring, Fast Ring. If you only want to
have a light for the ”ok to come out of bed” select the “No Ring Option”.
(Note: At this time you can adjust the volume of the ring, by pressing the “Light adj”
button. There are 3 volume options. Once you have selected the volume, press the Alarm
button again, to move to the light selection.)
5. Once the ring type is selected, push the “Alarm” button to continue
onto the light selection. The “setting icon and the light bulb icon” will be
flashing, and the clock will light up. (See Image 7)
6. Push the “Light bulb button” on the left side of the clock repeatedly to select the ok to
come out of bed color. (4 color options: Orange, Purple, Green and Red)
Note: at this point you can adjust the brightness of light by pressing the “Light Adj.” button, there are 3
brightness levels.
7. Once the light color is selected press the “Alarm button to save the alarm settings.
8. Your “Ok to come out of bed alarm/light is now set.
If you do not want to set a stay in bed light, press the alarm button one more time
and the clock will display the current time, with the “ok to come out of bed alarm
time shown above the current time. If you want to program a stay in bed light than
proceed to the next section.
This clock has 2 different wake up alarm settings:
1. OK TO COME OUT OF BED LIGHT/ALARM
• Alarm can be used to indicate when the child can come out of bed.
(Example: the alarm will light up (green) at 7 am to indicate its ok to come out of bed.)
• An audible alarm can also be set for this if you want.
2. STAY IN BED LIGHT
• Alarm can be used to indicate when a child needs to stay in bed.
(Example: If you do not want your child to get out of bed before 7am, the clock can be programmed
to light up [red] at 6:30 am [or any other AM Hour] and if the child wakes up and the clock is red. He/
she will know that it is too early and they need to wait patiently until the clock turns green to get out of
bed.)
• You can set and use these functions differently to fit you and your child needs
• This Clock also features a Nap Time Setting

8
SETTING THE STAY IN BED LIGHT
1. After pressing the “Alarm” button in the previous steps, the alarm time
will be displayed at the top of the screen, with “OFF” in the center of the
display. (See Image 8.)
2. Press the “Light Adj.” button to turn on the stay in bed light alarm. The
Stay in bed alarm time will be shown in the center of the display. Note:
This is the time in which you would like the clock to light up (Red) to let
your child know that it is still too early to get out of bed.
3. Push the “Hour & Min” buttons to set the time for the stay in bed light to turn on.
4. Push the “Big on the left hand side of the clock to select what color you want the clock
to light up for the stay in bed light alarm. (There are 3 color options: Orange, Red, and
Purple; Green was already used by Ok to come out of bed.)
5. Once the time and color have been set push the “Alarm” button. Now both the “Ok to
come out of bed”, and the “Stay in bed in light” alarms have been set. The current time
will be displayed in the center of the display with the “ok to come out of bed alarm time
shown above the current time. • Note: The stay in bed alarm and light will be saved, you
will not see it on the screen. If you go back into Alarm setting to check, your stay in bed
time setting will be erased and you will need to reprogram the timing.
SILENCING THE ALARM AND SNOOZE FUNCTION
When the alarm goes off you have two options
1. Turn the alarm ???????? “Big Bell button” on the clock’s right side.
2. To Snooze the alarm, press the “Big Light Bulb Button” on the clocks left side, this
snooze the alarm for 10 minutes. To Cancel a snooze at any time, press the “Big Bell
Button” on the clocks right side
TURNING OFF THE ALARM SETTINGS
The "OK to Come out of bed” and the “stay in bed light alarm” can both be turned off
completely so there is no alarm, or the stay in bed light alarm can be turned off leaving the
OK to come out bed alarm still active.
TURNING OFF ALL ALARM SETTINGS
1. Open the cover to the Control Panel and press the “Alarm” Button. The
the “ and the alarm time at the top of the display will disappear, and the
current time will be shown in the middle of the display. (See Image 9)
2. Now all alarms have been turned off, to turn the alarms back on simply
press the alarm button again. The the and the alarm time at the top
of the display will reappear. The Alarm is turned back on now.
8
NOTE: If Alarm button is held down for more than a brief second, it will lose the saved
alarm settings.

9
TURNING OFF ONLY THE STAY IN BED ALARM LIGHT
1. Press the “Alarm” button for 2 seconds, the and will start flashing.
Press the “Alarm” button 3 times, then press the “Light Adj.” button 1 time.
2. The Word “OFF” will be shown in the center of the display.
3. Press the “Alarm” button 1 time to save the alarm setting changes. The
Current time will be displayed in the center with the bell icon and alarm
time shown at the top of the display indicating the “OK to come out of
bed” alarm is still on. (See Image 10)
This clock has a nap time timer, making it easy to set an alarm for nap times without having to change the
existing alarm settings.
SETTING THE NAP TIME TIMER
1. Hold down the “Nap” button for 2 seconds, the “bell” ”settings” “clock icon” will flash
and 1:00 will appear in the center of the screen. (See Image 11)
2. Push the “Hour and Min” buttons to select the length of time for the nap timer. (Between
1:00 and 2:00 Hours), when the time has been adjusted press the nap button to save the
nap timer and to select the ring type.
3. Push the “Big Bell Button” on the clocks right side to select the ring type for when the
nap timer counts down to zero. (There are 2 ring options: Slow Ring, Quick Ring) Note:
At this time you can adjust the volume of the ring, by pressing the “Light adj” button.
There are 3 volume options. Once you have selected the volume, press the Alarm button
again, to move to the light selection.
4. Press the “Nap” Button to Save the Nap Timer Settings
STARTING THE NAP TIMER
1. Open the Cover to the Control Panel.
2. Press the Nap Button, The “Bell Icon” “Alarm Clock” icon and the selected timer will
show up on the display, and the Timer will start counting Down. See Image 12
3. When the Nap Timer has counted down and the alarm has sounded, The Nap Timer and
Alarm can be snoozed in the exact same way as the alarm.
• To Silence the alarm, press the “Big Bell button” on the clock’s right side
• To Snooze the alarm, press the “Big Light Bulb Button” on the clocks left side, this
will snooze the alarm for 10 minutes.
• To Cancel a snooze at any time, press the “Big Bell Button” on the clocks right side
4. To cancel the Nap Timer, press the nap button 1 time and the nap timer will be turned off
and the current time will be displayed on the clock.
NAP SETTINGS

10
STEP BY STEP
INSTRUCTIONAL VIDEO
Thank you for purchasing the Learn and Climb Stay in Bed Light Clock.
If you would like to see a video demonstrating the instructions
listed above please go to this web address:
https://youtu.be/dgervlnDZsg
Or for your convenience use the QR code
below and you will be taken to the instructional video.
ADVICE
9MAINTAIN THE CLOCK
The clock is not waterproof. Do not use the clock near the water.
9POWER SOURCE
This product should be connect to a power supply only of the type marked on the outside
off your USB wall/power adapter.
9USB SAFETY
This producut has the USB port and 1USB cable included. Please plug the USB cable into
the USB port correctly to avoid loose connectivity.

11
BATTERY SAFETY
• The Batteries power source are 4.5V~5.5V, please do not over this value.
• Batteries are small objects and a hazard to children, must be replaced by an adult.
• Follow the polarity (+/-) diagram in the battery compartment.
• Promptly remove dead batteries from the toy.
• Dispose of used batteries properly.
• Remove batteries from prolonged storage.
• Only batteries of the same type as recommended are to be used .
• DO NOT incinerate used batteries.
• DO NOT dispose of batteries in fire, as batteries may explode or leak .
• DO NOT mix old and new batteries.
• DO NOT mix alkaline, standard (carbon-zinc) or
• rechargeable (Ni-Cd, Ni-MH) batteries.
• DO NOT recharge non-rechargeable batteries.
• DO NOT short-circuit the supply terminals.
• Rechargeable batteries are to be removed from the toy before being charged.
• Rechargeable batteries are only to be charged under adult sup ervision.
8Clock does not turn ON or
does not respond.
8Clock makes strange sounds,
behaves erratically or makes
improper responses.
8Sound becomes weak or the
Clock suddenly stops working.
9Make sure batteries are correctly installed.
9Make sure battery cover is securely
attached.
9Remove batteries and put them back in.
9Clean battery compartment by rubbing
lightly with a soft eraser and then wiping
with a clean dry cloth.
9Install new batteries.
9Push the reset button to restart the clock.
If the problem persists, it may be caused by weak
batteries. Please install a new set of batteries and try
again.
TROUBLESHOOTING

12
E [e-mail] • P 888.888.8888 • W learnandclimb.com