Led lighting Followspot 1200 hmi User manual

We thank you for choosing the projector FOLLOWSPOT

1200 HMI.

To make the most of this unit and to make it work correctly

in the years, before connecting it to its source and using it,

we suggest you to carefully read this manual.

In this way you will be more familiar with it and its

connections and will be easier to use it.

very important warnings, to be read with the maximum attention;

important parts of the text that give details and/or explanations on the use of the

FOLLOWSPOT 1200 HMI;

practical advices for an ecient use of the FOLLOWSPOT 1200 HMI.

IMPORTANT

Make sure that the unit has not been damaged during the transportation.

In case it has happened or in case the unit does not work correctly, immediately contact the Retailer.

If the unit has been directly sent to you , immediately contact the Freight Company.

Only the nal receiver (the person or the Company that receive the unit) is in the position to

complain for the above inconveniences.

The safety of the unit is guaranteed only strictly following the instructions, so it is recommended to

accurately preserve them.

YOUR REFERENCE

Cite the model and the serial number anytime you contact your retailer to ask for information or assistance.

STANDARD PACKAGE

The standard package of the projector FOLLOWSPOT 1200 HMI contains:

1) Projector ON REQUEST:

)972060edoc(pmaL*W0021tsallaB)2

)701040edoc(mm35redloh-oboG*regnahcsruoloC)3

)045380edoc(dnatS*sedalbeliforp4)4

)289491edoc(sleehwhtiwesacthgilF*mm55sirI)5

6) User’s manual

7) Guarantee

IMPORTANT

User’s manual

product code: 991223

All the sections of this manual have been studied to make as easy and complete as possible the use of the

FOLLOWSPOT 1200 HMI.

To make the manual more clear and easy to consult, we have used the following symbols and conventions:

fig. 1

PMALPMAL PMAL PMALPMAL

)MARSO(SGW0021IMHpmalegrahcsiD

K°006.5:erutarepmetruoloC

ero057:efilpmalegarevA

SUCOFDNAMOOZSUCOFDNAMOOZ SUCOFDNAMOOZ SUCOFDNAMOOZSUCOFDNAMOOZ .launaM

LACITREVLACITREV LACITREV LACITREVLACITREV

TNEMEVOM

°54-/°54+

.)1.gif(noitatneirolaunaM

MAEBTHGILMAEBTHGIL MAEBTHGIL MAEBTHGILMAEBTHGIL

EDUTILPMA

)2.gif(°71/°8

REGNAHCSRUOLOCREGNAHCSRUOLOC REGNAHCSRUOLOC REGNAHCSRUOLOCREGNAHCSRUOLOC .)launam(etihw+sruoloc5

TUOKCALBTUOKCALB TUOKCALB TUOKCALBTUOKCALB .launaM

METSYSELIFORPMETSYSELIFORP METSYSELIFORP METSYSELIFORPMETSYSELIFORP .sedalbeliforptnednepedni4

.gniliforplaunaM

SIRISIRI SIRI SIRISIRI .launaM

REWOPTUPNIREWOPTUPNI REWOPTUPNI REWOPTUPNIREWOPTUPNI

.zH05;caV032:egatlovgnitarepolanimoN•

.W0421:ylppusrewopdetaR•

.)caV032(A01:tnerruclanimoN•

GNIKROWGNIKROW GNIKROW GNIKROWGNIKROW

NOITISOP

.dnatsanO

SNOISNEMIDSNOISNEMID SNOISNEMID SNOISNEMIDSNOISNEMID

)HxDxW(

rotcejorProtcejorP rotcejorP rotcejorProtcejorP.)1.gif(083x0711x023.mm

tsallaB.)1.gif(032x033x042.mm

THGIEWTHGIEW THGIEW THGIEWTHGIEW rotcejorProtcejorP rotcejorP rotcejorProtcejorP32.gK

tsallaB71.gK

YDOBYDOB YDOB YDOBYDOB .muinimuladnaleetS

FOLLOWSPOT 1200 HMI

CODE 991223

fig. 2

1170 mm.

380 mm.

MANUAL

ORIENTATION

KNOBS

BRACKET

LIGHT BEAM

REGULATION

SCREWS

230 mm.

320 mm.

240 mm.

330 mm.

TECHNICAL FEATECHNICAL FEA

TECHNICAL FEATURESTURES

TURESTURES

TURES

LIGHT BEAM AMPLITUDE RELATED TO DISTANCES

Amplitude

Distance in mt.

!Do not dismantle and modify the unit.

!Do not install the unit outdoors directly exposed to rain or moisture.

!To avoid any inflammable liquids, water or metal objects entering the unit.

!To avoid installing the unit close to heat sources. Never to lean the connecting cable on the hot unit.

!Replace the fuses with others of the same kind and value 5x20 250V 10A (fig. 4).

!The unit must be at a minimum distance of 50 cm. from the walls or from any inflammable material and 3 mt.

from lighted objects.

!The unit must be placed where it could be easily aerated. To avoid obstructing the in/out air gratings.

!Do not directly look at the Lamp when it is on.

WARNINGSARNINGS

ARNINGSARNINGS

ARNINGS

!Before installing the FOLLOWSPOT 1200 HMI, make sure that the carrying structure is safe and able to support the

weight of the unit.

The FOLLOWSPOT 1200 HMI is equipped with a bracket with a middle eye (diam. 12 mm.) to place it on stand (fig. 1).

To orientate the unit follow these instructions:

1) Unscrew the Manual Orientation Knobs on the side of the unit (fig. 1);

2) Orientate the projector as you want, using its proper handles (fig. 4 and 6);

3) Screw the Manual Orientation Knobs.

!At the end of the assembling operations make sure that the unit has been correctly and safely fixed.

ASSEMBLINGASSEMBLING

ASSEMBLING

fig. 4

Before connecting the unit to the mains, make sure that the working voltage and frequency correspond to the values

indicated on the label (fig. 4).

The FOLLOWSPOT 1200 HMI is made to work at a working voltage of 230V 50Hz; 10 A.

Connect the projector to the power supply through the feed box placed on the ballast (fig. 4).

For the power supply connection, do as follows:

1) open the feed box using a thin screw-driver and gently force the two lateral little tongues (fig. 4/a);

2) the connections from the unit to the power supply source are described in fig. 4/a;

3) close the feed box pressing on its cover;

4) at the end, connect the plug of the projector to the ILME socket of the ballast (fig. 4/a).

!The plug of the projector must be used only for the connection to the ballast.

Any other use could damage the lamp.

To start on the projector there is a green switch ON / OFF (fig. 4).

COLCOL

COLOURS CHANGER SYSTEM ASSEMBLINGOURS CHANGER SYSTEM ASSEMBLING

OURS CHANGER SYSTEM ASSEMBLINGOURS CHANGER SYSTEM ASSEMBLING

OURS CHANGER SYSTEM ASSEMBLING

FOLLOWSPOT 1200 HMI

CODE 991223

ON / OFF

SWITCH

PROFILE SYSTEM AND BLAPROFILE SYSTEM AND BLA

PROFILE SYSTEM AND BLACK OUTCK OUT

CK OUTCK OUT

CK OUT

fig. 3

fig. 3a

The FOLLOWSPOT 1200 HMI comes with a colours changer system (fig. 6), to assamble it, do as follows:

At the front of the projector there are 4 support connections where to mount the colours changer system (fig. 6).

At the back of the colours changer system, there are 4 guide-eyes.

Pull the safety spring at the front of the colours changer system (fig. 6) and precisely connect the 4 guide-eyes to

the 4 support connections, leave free the safety spring making sure that the colours changer system is well stable.

The colours changer system is able to be equipped with No. 5 coloured filters (gelatine).

To insert the gelatines, do as follows:

1) unfasten the three screws of the filter-holder (fig. 6);

2) insert the gelatine;

3) fasten the three screws.

PLUG

FUSE

HANDLE

ILME SOCKET

LABEL

It is recommended to use

only filters with an high

temperature resistance.

ZOOM AND FOCUSZOOM AND FOCUS

ZOOM AND FOCUS

To regulate the zoom and focus use the two knobs (fig. 6) placed on the right side of the projector. The light beam

amplitude can be regulated from a minimum of 8° to a maximum of 17° (fig. 2).

The FOLLOWSPOT 1200 HMI is provided with a profile system of 4 profile blades.

Insert the profile blades (fig. 3) in their appropriate side slots (fig. 6) to cut the beam to the required shape.

In the upper part of the projector has been made an appropriate room with a track to insert the Iris and the

Gobo-holder (fig. 6), available on request (ref. to standard package and fig. 3/a).

The FOLLOWSPOT 1200 HMI is provided with the black out function. It is possible to cut out the entire light beam

using the lever placed at the right side of the projector (fig. 6).

Profile blades

Iris

Gobo-holder

SLOT SIDE

CONNECTION TCONNECTION T

CONNECTION TO THE POWER SUPPLO THE POWER SUPPL

O THE POWER SUPPLO THE POWER SUPPL

O THE POWER SUPPLYY

HANDLE

The unit must be connected to the earth. The inobservance of these instructions automatically makes

the guarantee expiring.

IMPORTANT

FEED BOX

fig. 4/a

THIN SCREW-DRIVER

CABLE CLAMP

L = PHASE (Brown)

N = NEUTRAL (Blue)

= EARTH (Green - Yellow)

g. 6

SAFETY SPRING

COLOURS CHANGER

SUPPORTS

FILTERS HOLDER

SCREWS

BLACK OUT

LEVER

HANDLE

COLOURS CHANGER

SYSTEM

g. 5

To properly adjust the light beam:

• use the two adjusting screws placed at the back of the lower

cover of the projector together with a descriptive label.

Also, follow what described in the diagram in g. 1.

LAMP

THERMIC

PROTECTOR

LOCKING KNOB

TOP LAMP-HOLDER

SUPPORT

LOWER LAMP-HOLDER

1) Disconnect the unit before replacing the Lamp. Always wear protective gloves and goggles.

2) Unfasten the two knobs placed at the top of the projector (g. 6).

3) Take out the cover.

4) Take out the two lateral bushes of the new lamp.

5) Unscrew the locking knob of the top lamp-holder (g. 5).

6) Fasten the lamp in its lower lamp-holder (g. 5).

7) Screw the locking knob of the top lamp-holder.

8) Put back the top cover and fasten the two knobs.

!Before mounting the lamp, make sure that into the lamp holder there is not anything that may cause interruptions

to the thermic and electrical conduction.

FITTING AND REPLAFITTING AND REPLA

FITTING AND REPLA CING THE LAMPCING THE LAMP

CING THE LAMPCING THE LAMP

CING THE LAMP

In case of replacement of the Lamp or maintenance, never open the unit

unless are passed at least 15 minutes after it went o.

IMPORTANT

Rev. 12/2005Working to make its products always more perfect, LED reserves the possibility to make technical changes during the production. The technical features and the drawings on this

manual are not binding for LED and they could be changed at any time without notice. LED it is not responsible for any inconven ience caused by an improper or dierent use of

the unit respect to the one for what it has been made.

ZOOM AND

FOCUS KNOBS

PROFILE BLADE

LAMP ACCESS

HATCH KNOBS

HANDLE

IRIS OR

GOBO-HOLDER

! Before operating any maintenance disconnect the mains.