Ledj FOLL010 User manual

Order code: FOLL010
FS 100 LED Followspot
User Manual

www.prolight.co.uk FS 100 LED Followspot User Manual
2
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CARE-
FULLY BEFORE YOUR INITIAL START-UP!
• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.
• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.
• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary
fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.
• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand
thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.
Donotendangeryourownsafetyandthesafetyofothers!
Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!
• Neverletthepowercablecomeintocontactwithother
cables.Handlethepowercableandallmainsvoltage
connectionswithparticularcaution!
• Neverremovewarningorinformativelabelsfromtheunit.
• Donotopentheequipmentanddonotmodifytheunit.
• Donotconnectthisequipmenttoadimmerpack.
• Donotswitchtheequipmentonandoffinshortintervals,
asthiswillreducethesystem’slife.
• Onlyusetheequipmentindoors.
• Donotexposetoammablesources,liquidsorgases.
• Alwaysdisconnectthepowerfromthemainswhen
equipmentisnotinuseorbeforecleaning!Onlyhandle
thepower-cablebytheplug.Neverpullouttheplugby
pullingthepower-cable.
• Makesurethattheavailablemainssupplyvoltageis
between100~240VAC,50/60Hz.
• Makesurethatthepowercableisnevercrimpedor
damaged.Checktheequipmentandthepowercable
periodically.
• Iftheequipmentisdroppedordamaged,disconnectthe
mainspowersupplyimmediatelyandhaveaqualied
engineerinspecttheequipmentbeforeoperatingagain.

• Iftheequipmenthasbeenexposedtodrastic
temperatureuctuation(e.g.aftertransportation),
donotconnectpowerorswitchitonimmediately.
Thearisingcondensationmightdamagetheequipment.
Leavetheequipmentswitchedoffuntilithasreached
roomtemperature.
• Ifyourproductfailstofunctioncorrectly,stopuse
immediately.Packtheunitsecurely(preferablyinthe
originalpackingmaterial),andreturnittoyourProLight
dealerforservice.
• Onlyusefusesofsametypeandrating.
• Repairs,servicingandpowerconnectionmustonlybe
carriedoutbyaqualiedtechnician.THISUNITCONTAINS
NOUSERSERVICEABLEPARTS.
• Thislightingxtureisforprofessionaluseonly-itis
notdesignedfororsuitableforhouseholduse.The
productmustbeinstalledbyaqualiedtechnicianin
accordancewithlocalterritoryregulations.Thesafetyof
theinstallationistheresponsibilityoftheinstaller.The
xturepresentsrisksofsevereinjuryordeathduetore
hazards,electricshockandfalls.
• Warning!RiskGroup2LEDproductaccordingto
EN62471.Donotviewthelightoutputwithoptical
instrumentsoranydevicethatmayconcentratethebeam.
• WARRANTY:Oneyearfromdateofpurchase.

www.prolight.co.uk FS 100 LED Followspot User Manual
3
Product overview & technical specications
TheLEDJFS100Followspotfeatures6dichroiccoloursplusopencoldwhite,3200Kwarmwhitelter,an
electronicshutterforinstantaneousblackout,a9°-14°beamangle,manualfocusing,manualirisandrear
positioninghandle.OnboardDMXcontrolalsogivestheusertheexibilitytocontrolthedimmer,shutterand
colourwheelfromaDMXlightingconsole.
•1x100WcoolwhiteLED
•Adjustablebeamangle:9°-14°
•15kHzrefreshrate
•Manualfocus&zoom
•Electronicblackout
•Manualiris
•Colourwheel:7dichroiccolours,3200K,red,
yellow,blue,green,purplepink+open
•DMXchannels:2
•0-100%dimming
•Rearpositioninghandle
•3pushbuttonmenuwithLEDdisplay
•PowerCONinput
•3-PinXLRinput/output
•Fancooled
FS 100 LED Followspot
Specications
Powerconsumption 118W
Powersupply 100~240V,50/60Hz
Fuse F2A250V
Dimensions 270x280x585mm
Weight 6.4kg
Ordercode FOLL010
0m 3m 5m 7m 8m
9° - Lux
14° - Lux
3930
2260
1m
35600
18090
1300
810
14°
710
412
583
310
9°
585mm280mm
270mm

www.prolight.co.uk FS 100 LED Followspot User Manual
4
www.prolight.co.uk
FOCUS
ZOOM
IRIS
ON
OFF
POWER INPUT:
100-240V~50/60Hz
FUSE:
F2A 250V
100W LED FOLLOWSPOT
DOWN
FUNCTION SELECT
OPEN
COOL
WHITE
WARM
WHITE RED YELLOW
BLUE GREEN PURPLE PINK
BLACKOUT
SHUTTER
• DMX MODE
• MANUAL MODE
UP
Technical specications
01-Dimmingknob
02-DMXinput
03-DMXoutput
04-Colourbuttons
05-Shutterbuttons
06-LEDdisplay
07-Functionbuttons
08-PowerCONinput
09-Fuse:F2A250V
10-On/Offswitch
11-Earthpoint
12-Zoom
13-Focus
14-Iris
Inthebox:1 x xture,
1 x power cable &
1 x user manual
04 07 09
10
11
13
14
05 06 08 12
DMX INPUT
DMX OUTPUT
DIMMING
MIN MAX
DMX INPUT
DMX OUTPUT
DIMMING
MIN MAX
03 02
01

www.prolight.co.uk FS 100 LED Followspot User Manual
5
Operating instructions
Functions:
Dimmer-Turnclockwisetoincreasetheintensity,andanti-clockwisetodecreasetheintensity.
Shutter-TheLEDdisplaywillshowonwhentheshutterisopenandofFwhentheshutterisclosed.
Colourbuttons-Allowstheusertochoosebetween6coloursplus3200Kandopen.
Functionselectionbutton-UsethisbuttontoswitchbetweenDMXandManualmodes
(ModeisindicatedbyLEDsabovedisplay)
LEDdisplay/StatusLEDs-TheLEDdisplayshowstheDMXaddressandxturestatus.ThestatusLEDs
showtheuserwhethertheunitisinDMXorManualmodesandwhetheritisreceivingaDMXsignal.
Up/downbuttons-TheseareusedtochangetheDMXaddress.
DMX mode:
OperatinginaDMXcontrolmodeenvironmentgivestheuserthegreatestexibilitywhenitcomesto
customisingorcreatingashow.Inthismodeyouwillbeabletocontroleachindividualtraitofthexture
andeachxtureindependently.
ToaccesstheDMXmode,pressthe“FUNCTION SELECT”buttonontherearoftheunittoshow--1on
theLEDdisplayandtheDMXmodeLEDisilluminated.TheunitisnowinDMXmode.Nowusethe“UP”
and“DOWN”buttonstosetthedesiredDMXaddress.
Manual mode:
Toaccessthemanualmode,pressthe“FUNCTION SELECT”buttonontherearoftheunituntilthe
ManualmodeLEDisilluminated.Theunitisnowinmanualmode.Nowusetheshutterandcolour
buttonsalongwiththedimmingknobtocontroltheunit.
Channel Value Function
1 000-031 Open(coolwhite)
032-063 3200K
064-095 Red
096-127 Yellow
128-159 Blue
160-191 Green
192-223 Purple
224-255 Pink
2000-255 Masterdimmer(0-100%)
2 channel mode:

www.prolight.co.uk FS 100 LED Followspot User Manual
6
Setting the DMX address:
TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”
from1-512.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel
indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas
addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105
and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe
chainstartsat107.
DMX 512:
DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent
xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.
DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”
XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).
DMX linking:
DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether
andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.
ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest
cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe
DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein
aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda
DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,
nomatterwhereitislocatedintheDMXchain.
DATA cable (DMX cable) requirements (for DMX operation):
ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.
YourunitandyourDMXcontrollerrequireastandard3-pinXLRconnectorfordatainput/output,
seeimagebelow.
Also remember that DMX cable must be daisy chained and cannot be split.
DMX setup
FurtherDMXcablescanbe
purchasedfromallgoodsound
andlightingsuppliersor
ProLightConceptsdealers.
Pleasequote:
CABL10 – 2m
CABL11 – 5m
CABL12 – 10m

www.prolight.co.uk FS 100 LED Followspot User Manual
7
Notice:
Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables
shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs
outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.
Special note:
Line termination:
Whenlongerrunsofcableareused,
youmayneedtouseaterminatoron
thelastunittoavoiderraticbehaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order ref: CABL9O, 5-pin - Order ref: CABL89)
5-pin XLR DMX connectors:
Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures
maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa
3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.
Terminationreducessignaltransmission
problemsandinterferance.itisalways
advisabletoconnectaDMXterminal,
(resistance120Ohm1/4W)betweenpin2
(DMX-)andpin3(DMX+)ofthelastxture.
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
DMX setup

www.prolight.co.uk FS 100 LED Followspot User Manual
8
WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
Thismarkingshownontheproductoritsliterature,indicatesthatitshouldnotbedisposedof
withotherhouseholdwastesattheendofitsworkinglife.Topreventpossibleharmtothe
environmentorhumanhealthfromuncontrolledwastedisposal,pleaseseparatethisfromother
typesofwastesandrecycleitresponsiblytopromotethesustainablereuseofmaterialresources.
Householdusersshouldcontacteithertheretailerwheretheypurchasedthisproduct,ortheir
localgovernmentofce,fordetailsofwhereandhowtheycantakethisitemforenvironmentally
saferecycling.
Businessusersshouldcontacttheirsupplierandcheckthetermsandconditionsofthe
purchasecontract.Thisproductshouldnotbemixedwithothercommercialwastesfordisposal.