Leeson SM series User manual

Variable Speed AC Motor Drives
SM Series
Quick Reference Guide
7KLVJXLGHLVLQWHQGHGDVDQDLGWRFRQILJXUHWKH606HULHVGULYH
NOTE: %HIRUHLQVWDOOLQJDQG RSHUDWLQJWKH 60GULYH SOHDVH
UHDGDQGEHFRPH IDPLOLDUZLWK WKH 60 6HULHV LQVWDOODWLRQ
DQGRSHUDWLRQPDQXDO
6KRZQEHORZDUHWZRVDPSOHZLULQJGLDJUDPVLQFOXGLQJ
IRUZDUGUHYHUVHGLUHFWLRQFRQWURO2QHVKRZVDWKUHHZLUH
VWDUWVWRSFRQWUROXVLQJPRPHQWDU\FRQWDFWVDQGWKHRWKHUVKRZVD
ZLUHVWDUWVWRS FRQWUROXVLQJ PDLQWDLQHGFRQWDFWV 5HTXLUHG
SDUDPHWHUVHWWLQJVDUHDOVRLQFOXGHG
:,5(67$576723
6HW3DUDPHWHU7%$
WR6WDUW5HYHUVH
6HW3DUDPHWHU 7%(
WR6WDUW)RUZDUG
6HW3DUDPHWHU5RWDWLRQ
WR)RUZDUGDQG5HYHUVH 
SM TERMINAL STRIP DIAGNOSTIC AND DISPLAY MESSAGES
BULLETIN #2454
3577S/1000/6-02/RL/BH
STOP
SIGNAL COMMON
0-10 VDC SPEED REFERENCE INPUT
SPEED POT POWER SUPPLY
DIGITAL INPUT REFERENCE
TB-13A FUNCTION SELECT
TB-13B FUNCTION SELECT
TB-13E FUNCTION SELECT
4-20 mA SPEED REFERENCE INPUT
DISPLAY DESCRIPTION
Speed Reference Codes
CP CONTROL PAD: The drive speed is controlled by the and buttons on the front of the drive.
EI EXTERNAL CURRENT: The drive speed is controlled by a 4-20 mA signal between TB-25 and TB-2
EU EXTERNAL VOLTAGE: The drive speed is controlled by a 0-10 VDC signal between TB-5 and TB-2.
JG JOG: The drive is in Jog mode and the speed is set by preset speed #2 (Parameter 32).
OP MOP: Contacts wired to TB-13B and 13C are used to increase and decrease the drive speed.
Pr1-Pr7 PRESET SPEEDS #1-7: The drive speed is set by the selected Preset Speed (Parameters 31-37).
Status Indication
br DC BRAKING: The DC braking circuit is activated.
CL
CURRENT LIMIT: The output current has exceeded the CURRENT LIMIT setting (Parameter 25)
and the drive is reducing the output frequency to reduce the output current. If the drive
remains in CURRENT LIMIT for too long, it can trip into a CURRENT OVERLOAD fault (PF).
Er ERROR: Invalid data has been entered.
GE “GE” will be displayed if an attempt is made to change the OEM default settings when the
drive is operating in the OEM mode (see Parameter 48).
LC FAULT LOCKOUT: Failed three restart attempts. Requires a manual reset.
SE SERIAL: The optional remote keypad is active as the user interface instead of the buttons on the
front of the drive.
SP START PENDING: This is displayed during the 15 second interval between restart attempts.
Diagnostic Codes
AF HIGH TEMPERATURE FAULT: Ambient temperature is too high.
CF CONTROL FAULT: A blank EPM, or EPM with corrupted data has been installed. Perform a
factory reset (Parameter 48).
cF INCOMPATIBILITY FAULT: An EPM with a different parameter version has been installed.
dF DYNAMIC BRAKING FAULT: The drive has sensed the dynamic braking resistors are overheating.
EF EXTERNAL FAULT: TB-13A and/or TB13C is set as an external fault input and TB-13A and/or
TB-13C is open with respect to TB-2.
GF DATA FAULT: User data and OEM defaults in the EPM are corrupted.
HF HIGH DC BUS VOLTAGE FAULT: Line voltage is too high; Deceleration rate is too fast;
Overhauling load. Fast deceleration and overhauling loads may require dynamic braking.
JF REMOTE KEYPAD FAULT: The communication link between the drive and the optional Remote
Keypad has been lost. Check for proper wiring and/or noise.
LF LOW DC BUS VOLTAGE FAULT: Line voltage is too low.
OF OUTPUT TRANSISTOR FAULT: Phase to phase or phase to ground short circuit on the
output: Failed output transistor: Boost settings are too high: Acceleration rate is too fast.
PF CURRENT OVERLOAD FAULT: VFD is undersized for the application: Mechanical problem with
the driven equipment.
SF SINGLE-PHASE FAULT: Single-phase input power has been applied to a three-phase drive.
UF START FAULT: Start command was present when the drive was powered up. Must wait
2 seconds after power-up to apply Start command if START METHOD is set to NORMAL.
F1 EPM FAULT: The EPM is missing or damaged.
FC,F2-Fo INTERNAL FAULTS: The control board has sensed a problem. Consult factory.

:,5(67$576723
6HW3DUDPHWHU7%$
WR5XQ5HYHUVH
6HW3DUDPHWHU5RWDWLRQ
WR)RUZDUGDQG5HYHUVH 
1
2
5
6
11
13A
13B
13E
25
16
17
PROGRAMMABLE FORM A RELAY
1 2 5 6 11 13A 13B 13E 25
Momentary Momentary
Stop Contact Start Contact
1 2 5 6 11 13A 13B 13E 25
Maintained Maintained
Run Forward Run Reverse
Contact Contact
REV FWD
A Subsidiary of REGAL-BELOIT CORPORATION

CONFIGURING THE SM DRIVE
Entering Program Mode:
7RDFFHVVWKHSDUDPHWHUVSUHVVWKHMode EXWWRQ7KLVZLOODFWLYDWH
WKHSDVVZRUGSURPSW7KHGLVSOD\ZLOOUHDG´µDQGWKHULJKWKDQG
GHFLPDOSRLQWZLOOEHEOLQNLQJ8VHWKH ▲DQG▼EXWWRQVWRVFUROO
WRWKHSDVVZRUGYDOXHWKHIDFWRU\GHIDXOWSDVVZRUGLV DQGSUHVV
Mode WRHQWHU
Connections:
%HORZ LV D VDPSOH ZLULQJ GLDJUDP IRU WZRZLUH VWDUWVWRS FRQWURO
7KHGULYHLVUHDG\WRXVHULJKWRXWRIWKHER[ZLWKWKHVHVLPSOHFRQ
WUROZLULQJ FRQQHFWLRQVQR SDUDPHWHUDGMXVWPHQWV DUHUHTXLUHG
6SHHG LV FRQWUROOHG IURP WKH ▲DQG ▼EXWWRQV RQ WKH IURQW RI WKH
GULYH
3UHVVMode
'LVSOD\UHDGV´µ
8SSHUULJKWGHFLPDOSRLQWEOLQNV
7RDGGDSRWHQWLRPHWHU IRUVSHHG FRQWUROFKDQJH 3DUDPHWHU
6WDQGDUG6SHHG6RXUFHWR9'&
NO. Parameter Range of Factory
Name Adjustment Default
01 Line Voltage High (01), Low (02) High (01)
02 Carrier Frequency 6 kHz (02)
03 Start Method Normal (01)
04 Stop Method Coast (01)
05 Speed Source Keypad (01)
06 Relay Output None (01)
10 TB-13A Select None (01)
11 TB-13B Select None (01)
TB-13E Input Functions
12 TB-13E Output Functions None (01)
Other
14 Control
16 Units Editing Tenths of Units (01), Whole Units (02) Whole Units (02)
SM PARAMETER MENU
4 kHz (01), 6 kHz (02),
8 kHz (03), 10 kHz (04)
Normal (01), Start on Power-up (02),
Start w/DC Brake (03),
Auto Restart w/DC Brake (04),
Flying Restart 1 (05),
Flying Restart 2 (06),
Flying Restart 3 (07)
Coast (01), Coast with
DC Brake (02), Ramp (03),
Ramp with DC Brake (04)
Keypad (01), Preset #1 (02),
0-10 VDC (03), 4-20 mA (04)
None (01), Run (02), Fault (03),
Inverse Fault (04), Fault Lockout (05),
At Set Speed (06), Above Preset #3 (07),
Current Limit (08), Auto Speed (09),
Reverse (10), DB Brake (11)
None (01), 0-10 VDC (02),
4-20 mA (03), Preset Speed #2 (04),
Decrease Freq (05), Start Forward (06),
Jog Forward (07), Jog Reverse (08),
External Fault (09),
Inverse External Fault (10),
Auxiliary Stop (11), Accel/Decel #2 (12),
Remove Keypad (13)
None (01), 0-10 VDC (02),
4-20 mA (03), Preset Speed #1 (04),
Start Forward (05), Run Reverse (06),
Start Reverse (07), External Fault (08),
Inverse External Fault (9),
Auxiliary Stop (10), Accel/Decel #2 (11)
NO. Parameter Range of Factory
Name Adjustment Default
17 Rotation Forward Only (01), Forward Only
Forward and Reverse (02) (01)
19 Acceleration Time 0.1 - 3600.0 sec 20.0 sec
20 Deceleration Time 0.1 - 3600.0 sec 20.0 sec
21 DC Brake Time 0.0 - 3600.0 sec 0.0 sec
22 DC Brake Voltage 0.0 - 30% 0%
\23 0.0-Maximum Frequency 0.0 Hz
24 Minimum Frequency - 240.0 Hz 60.0 Hz
25 Current Limit 30 - 180% 180%
26 Motor Overload 30 - 100% 100%
27 Base Frequency 25.0 - 500.0 Hz 60.0 Hz
28 Fixed Boost 0.0 - 30.0% 1.0%
29 Accel Boost 0.0 - 20.0% 0.0%
30 Slip Compensation 0.0 - 5.0% 0.0%
31-37 Preset Speeds 0.0 - Maximum Frequency 0.0 Hz
38 Skip Bandwidth 0.0 - 10.0 Hz 0.0 Hz
39 Speed Scaling 0.0 - 6500.0 0.0
42 Accel/Decel #2 0.1 - 3600.0 sec 20.0 sec
43 Serial Address 1 - 247 1
44 Password 000-999 225
45 Spd at Min Signal Minimum Frequency - 999 Hz 0.0 Hz
46 Spd at Max Signal Minimum Frequency - 999 Hz 60.0 Hz
47 Clear History Maintain (01), Clear (02) Maintain (01)
User Settings (01),
48 Program Selection OEM Settings (02), Reset OEM (03),
Reset 60 (04), Reset 50 (05),
Translate (06)
50 Fault History View Only (N/A)
51 Software Code View Only (N/A)
52 DC Bus Voltage View Only (N/A)
53 Motor Voltage View Only (N/A)
54 Load View Only (N/A)
55 0-10 VDC Input View Only (N/A)
56 4-20 mA Input View Only (N/A)
57 TB Strip Status View Only (N/A)
58 Keypad Status View Only (N/A)
Minimum
Frequency
Maximum
Frequency
User Settings
(01)
2QFHWKH352*5$0PRGHLVDFFHVVHGXVHWKH▲DQG▼EXWWRQVWR
VFUROOWR WKHGHVLUHGSDUDPHWHU QXPEHU DQGSUHVVWKH Mode EXWWRQ
WRVHHWKHSDUDPHWHUVHWWLQJ8VHWKH▲DQG▼EXWWRQVWRFKDQJHWKH
SDUDPHWHUVHWWLQJDQGSUHVVMode WRVWRUHWKHQHZVHWWLQJ
8VH▲DQG▼WRVFUROOWRWKHSDVVZRUG
YDOXHIDFWRU\GHIDXOWSDVVZRUGLV 
3UHVVMode WRHQWHUSDVVZRUG
None (01), 0-10 VDC (02),
4-20 mA (03), Preset Speed #3 (04),
Increase Freq (05), Start Forward (06),
External Fault (07),
Inverse External Fault (08),
Auxiliary Stop (09),
Accel/Decel #2 (10).
Run (11), Fault (12), Inverse Fault (13),
Fault Lockout (14, At Set Speed (15),
Above Preset #3 (16),
Current Limit (17), Auto Speed (18),
Reverse (19), Dynamic Braking (20),
Remote Keypad (21)
Terminal Strip Only (01),
Remote Keypad Only (02)
Terminal Strip
(01)
1 2 5 6 11 13A 13B 13E 25
Maintained
Run/Stop
Contact
1 2 5 6 11 13A 13B 13E 25
Maintained
Run/Stop
Contact
Speed Pot