Lenofocus LRD03 User manual
Lenofocus
WiFi Camera User Manual
LRD03
1
Thank you for your purchase of Lenofocus LRD03 WiFi Camera. Please read
this manual before operation and keep it handy for future use.
Wi-Fi camera requires set up before working. The camera will not work
properly if user operates it incorrectly. If the camera has any issues, please
you return the camera.
Package Contents
Check if the following items are included in your camera package. If anything
is missing, contact the retailer from which you purchased the camera.
1x Lenofocus LRD03 WiFi Camera
1x USB Charging Cable
1x User Manual
1x Micro SD Card Reader
2
1x Reset Pin
Memory Cards
The camera supports 8 – 128GB micro SD card. The SD card must be High
Speed, we suggest to use U3 Speed Class micro SD card. If the camera can’t
record video on the micro SD card, please format your SD card and try again.
Safety Precautions
Failure to follow these steps each time may result in damage to your camera,
and could possibly destroy your camera. Your warranty does not cover
accidental damage or issues caused by user error.
*The camera is not drop resistant, therefore please avoid unnecessary
roughness when handling the camera. Try to avoid dropping or damaging the
camera in any way.
3
*Don’t keep the camera in moist circumstances for long periods of time.
*Don’t keep the camera in high temperatures as it may cause damage of
external and internal components.
*Use a specialized cloth to clean the camera lens and wipe away fingerprints
or dust.
*For the best and most efficient usage of your battery, we suggest using it in
0-40 °C.
*When inserting or removing the micro SD card, please keep the camera
turned off to avoid damage of the card or saved files.
*Store the camera in a dry place and remove the micro SD card if storing for
long periods of time.
Notice:
The product contains lithium-ion polymer batter, please dispose of it with
proper method according to your local regulations. You can dispose of it at a
recycling center or hazardous waste collection site.
4
Camera Structure
5
About Charging
Before using the camera for the first time, please fully charge the camera. You
can connect the camera to a USB charger or computer / laptop with USB cable
for charging.
LED Indicator Status
Charging Status
Blue light flashes and red light is
solid on
Charging
Blue light flashes and green
light is solid on
Fully charged
BASIC OPERATION
When using the camera for the first time.
6
A. Download Mobile APP
Download and install the JXLCAM app on your mobile device.
Search for JXLCAM on the Google Play Store for Android devices, or on the
Apple App Store for iOS devices.
Or you can scan the flowing QR code to download and install the JXLCAM
app on your mobile device.
B. Inserting micro SD card
Insert your micro SD card into the camera, please notice the correct direction.
Please allow all permissions of the app
when you install it, otherwise the app
will not work properly.
7
Push the card until it locks into place with a click.
C. Turning the camera on / off
Move up the Power Switch to turn the camera on. Blue light flashes. Move
down the Power Switch to turn the camera off.
If the camera is turned on while it is charging, the camera will record video
continuously.
D. Local Mode (Blue light is blinking)
The camera supports WiFi hotspot. You can connect your mobile device to the
camera directly and monitor live video. (Mobile device can’t access micro SD
card inside the camera under WiFi hotspot connection). Make sure the camera
has enough batter power. Low battery power causes connection failed.
8
1. Open settings. 2. Click WLAN. 3. Connect camera (ACCQ***)
9
4. Open JXLCAM app. 5. Click AP. 6. Watch live video.
10
Notice:
1. Under AP mode, the distance between camera and mobile device should
be less than 10 meters.
2. Under AP mode, when your mobile device connects to the camera, the
camera will stop recording video on micro SD card. You have to reset the
camera or restart the camera after your mobile device disconnect from the
camera, and then the camera will record video on micro SD card again.
E. Remote Mode (Android Devices) (Blue light is solid on)
Make sure 2.4G WiFi signal is available before operation. This WiFi camera
only supports 2.4G WiFi Network. Please notice: if your WiFi router is dual
bands 2.4G and 5G WiFi router, you have to connect your mobile device to
the 2.4G WiFi manually. If your router combined 2.4G WiFi and 5G WiFi into
one name, please login to your router and cancel the WiFi combination.
11
1. Open JXLCAM app. 2. Allow Permission. 3. Allow Permissions.
12
4. Click +. 5. AP add camera. 6. Click ...
13
7. Choose your router. 8. Input password. 9. Click ...
14
10. Choose the camera. 11. Click Add Camera. 12. Wait.
15
13. Next. 14. Next. 12. Click and watch video.
16
F. NOTE
1. When the camera is connected successfully, LED indicator changes to
blue solid on.
2. Low battery causes connection failed. Charge, reset and set up again.
3. If connection failed, check if WiFi name and password is correct; put your
mobile device and camera close to your router, and then reset the camera
and set up again.
4. If the app homepage shows the camera is offline, check if the camera is
powered on, and refresh the page by clicking the Refresh icon in the upper
right corner (For Android device); or restart the camera (For all devices).
G. Remote Mode (iOS Devices: iPhone, iPad)
Make sure 2.4G WiFi signal is available before operation. This WiFi camera
only supports 2.4G WiFi Network. Open the JXLCAM app before the following
operations.
17
1. Click +. 2. Click. 3. Click …
18
4. Click Settings. 5. Click WLAN. 6. Choose your router.
19
7. Go to open JXLCAM. 8. Input password. 9. Click ....
Table of contents
