Bosch VEZ Series Guide

AutoDome Easy II
VEZ Series
en Mounting Manual

AutoDome Easy II Table of Contents | en 3
Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02
Table of Contents
1 Important Safety Instructions 5
2 Unpacking 7
2.1 Parts List 7
3 Description 9
4 Installing a Surface Mount 10
4.1 Description 10
4.1.1 Additional Tools Required 10
4.1.2 Preparing the Surface Mount for an Indoor Installation 11
4.1.3 Preparing the Surface Mount for an Outdoor Installation 12
4.1.4 Installing the Camera to the Mounting Plate 17
5 Installing a Wall Mount 20
5.1 Description 20
5.1.1 Additional Tools Required 20
5.1.2 Preparing the Wall Mount for an Indoor Installation 21
5.1.3 Preparing the Wall Mount for an Outdoor Installation 23
5.1.4 Installing the Camera to the Mounting Plate 26
6 Installing a Recessed Mount 30
6.1 Description 30
6.1.1 Additional Requirements 30
6.1.2 Preparing the Ceiling for Installation 30
6.1.3 Installing the Camera to the Mounting Plate 34
7 Installing a Pipe Mount 38
7.1 Description 38
7.1.1 Tools/Supplies Required 38
7.1.2 Preparing the Ceiling for Installation 39

4en | Table of Contents AutoDome Easy II
F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
7.1.3 Installing the Camera to the Mounting Plate 44
Index 47

AutoDome Easy II Important Safety Instructions | en 5
Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02
1 Important Safety Instructions
Type numbers:
Read, follow, and retain all of the following safety instructions.
Heed all warnings on the unit and in the operating instructions
before operation.
1. Clean only with a dry cloth. Do not use liquid cleaners or
aerosol cleaners.
2. Do not install unit near any heat sources such as radiators,
heaters, stoves, or other equipment (including amplifiers)
that produce heat.
3. Do not block any ventilation openings.
4. Do not use the unit near water or expose to rain or
moisture. Never spill liquid of any kind on the unit.
5. Unplug the unit during lightning storms or when unused for
long periods.
6. Adjust only those controls specified in the operating
instructions.
7. Do not overload outlets and extension cords, as this can
cause fire or electrical shock.
8. Protect the plug and power cord from foot traffic or
pinching, at electrical outlets, and at its exit from the unit.
9. Operate the unit only from the type of power source
indicated on the label.
10. Unless qualified, do not attempt to service a damaged unit
yourself. Refer all servicing to qualified service personnel.
11. Use only replacement parts specified by the manufacturer.
12. Install in accordance with the manufacturer's instructions
in accordance with applicable local codes. Use only
attachments/accessories specified by the manufacturer.
Equipment change or modification could void the user's
guarantee or authorization agreement.

6en | Important Safety Instructions AutoDome Easy II
F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
You can view and print the full version of this Installation
Manual with Adobe Acrobat Reader, both provided on the
enclosed CD-ROM. This user guide is the intellectual property
of Bosch Security Systems; protected by copyright. Contact:
www.BoschSecurity.com
DANGER!
High risk: This symbol indicates an imminently hazardous
situation such as “Dangerous Voltage” inside the product.
If not avoided, this will result in an electrical shock, serious
bodily injury, or death.
WARNING!
Medium risk: Indicates a potentially hazardous situation.
If not avoided, this could result in minor or moderate bodily
injury.
CAUTION!
Low risk: Indicates a potentially hazardous situation.
if not avoided, this could result in property damage or risk of
damage to the unit.

AutoDome Easy II Unpacking | en 7
Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02
2 Unpacking
This equipment should be unpacked and handled with care. If
an item appears to have been damaged in shipment, notify the
shipper immediately.
Verify that all the parts listed in the Parts List below are
included. If any items are missing, notify your Bosch Security
Systems Sales or Customer Service Representative.
The original packing carton is the safest container in which to
transport the unit and must be used if returning the unit for
service. Save it for possible future use.
This installation should be made by qualified service personnel
and conform to the National Electrical Code and applicable
local codes.

8en | Unpacking AutoDome Easy II
F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
2.1 Parts List
The following table lists the parts included:
Quantity Part
1 Wall mount: VEZ-A2-WW or VEZ-A2-WC (white or charcoal)
1 Dome mounting cap
3M4screws
1 #10 screw
1 Installation manual
Quantity Part
1 Pipe mount: VEZ-A2-PW or VEZ-A2-PC (white or charcoal)
1 Dome mounting cap
2 Pipe mount extension poles 20 cm (7.9 in.) and 30 cm
(11.8 in.)
3M4screws
1 Pipe extension coupler
1Ceilingflange
1 #10 screw
1 Installation manual
Quantity Part
1 In-ceiling mount: VEZ-A2-IC
1 White trim ring with 2 (two) M3 captive screws
1 Black trim ring with 2 (two) M3 captive screws
1 Recess mount assembly
1 Installation manual

AutoDome Easy II Description | en 9
Bosch Security Systems, Inc. Mounting Manual F.01U.141.122 | 2.0 | 2010.02
3 Description
The AutoDome Easy II is part of a larger building block for any
surveillance/security system. By using multiple keyboard
controllers and multiple dome cameras, no place is too large for
monitoring. Extensible and flexible architecture facilities
remote control functions for a variety of external switching
devices such as multiplexers and DVRs.
This installation should be made by qualified service personnel
and conform to the National Electrical Code and applicable
local codes.
NOTICE!
A grounded conduit is required in order to meet the EMC
Regulation Requirements.

10 en | Installing a Surface Mount AutoDome Easy II
F.01U.141.122 | 2.0 | 2010.02 Mounting Manual Bosch Security Systems, Inc.
4 Installing a Surface Mount
4.1 Description
This chapter details how to mount the AutoDome Easy II to a
hard surface. The AutoDome Easy II is also suitable for wall
(Section 5 Installing a Wall Mount, page 20), recess
(Section 6 Installing a Recessed Mount, page 30), and pipe
mounting (Section 7 Installing a Pipe Mount, page 38). For
specific directions on mounting the unit, see the manual that
came with your mount.
For an outdoor installation you must obtain the Surface Mount
Junction Box (VEZ-A2-JC or VEZ-A2-JW) and the gaskets and O-
rings supplied with an AutoDome Easy II Outdoor Camera to
ensure a water-tight environment inside the unit and to
maintain an IP Environmental Protection Rating. Refer to
Section 4.1.3 Preparing the Surface Mount for an Outdoor
Installation, page 12, to start an outdoor installation.
NOTICE!
The image sensors in modern CCD cameras are highly sensitive
and require special care for proper performance and extended
lifetime. Follow the guidelines for optimum results with your
camera:
– Do not expose to direct sunlight or bright spotlights in
operating and nonoperating conditions.
– Avoid bright lights in the field of view of the camera. Bright
lights cause a “smearing” effect, which is visible as white
lines above and below the highlight. Prolonged exposure to
bright lights may cause bleaching of the sensor's color
filters. This will be visible as colored spots in the picture
and is irreversible.