Leon LAURA PLUS User manual

Assembly Instruction
LAURA PLUS
for wooden doors
LP01D

13 17a
18
10
6
9
3
14
15
10
9
8
4
9
16

1. x1 6. x1 11.
* x1 16.
min. x2
2. x1 7. x1 12. *
x1 17. a. x2 b. x2
3. x1 8.
x1 13. *
x1 18.
x1
4. x1 9. x4 x4 14. 5x35
min. x4 19. 3,5x22 x2
5. x2 10.
min. x4 15.
M5x16 min. x4 20.
x1
opcja
19
16
11
5
4
2
1
15 14
12
7
4
17a
17b
20

1

2
A. Unpack the components of
Lara Plus door frame
B. Insert snap-on corners [10]
and two-part expansion
corners [9] into the vertical
profiles of the rear trim
[6 and 7]
C. Assemble the vertical profiles
[6 and 7] with the horizontal
profile [8] of the rear trim
D. Tighten the bolt in the snap-on
corner [10] through the service
hole in the horizontal profile [8]
until the profiles join
10
76
8
7
9
7
8
76
8
8
10

E. Tighten grub screws in the
expansion corners [9], making
sure that the profiles are joined
evenly
F. Make sure that well-assembled
components of hinge fastening
are present on the inner side of
the door frame body
G. Proceeding in the same way
as in the case of rear trim,
insert snap-on corners [10]
and two-part expansion
corners [9] into the vertical
profiles of the door frame body
[1 and 2]
H. Assemble the vertical profiles
[1 and 2] with the horizontal
profile [3] of the door frame
body
3
9
12
3
10
9
1
1
3
12
3
12
3

I. Tighten the bolt in the snap-on
corner [10] through the service
hole in the horizontal profile [3]
until the profiles join
J. Tighten grub screws in the
expansion corners [9], making
sure that the profiles are joined
evenly
K. Insert the wall seal [5] into the
seat of the door frame’s rear
trim along the whole
circumference of profiles
L. Proceed in the same way
in the case of door frame body
4
3
10
9
5
5
12
3
76
8
12
3
12
3

M. Correctly assembled door frame
components - body and rear
trim
N. Insert the assembled door
frame body into the
construction opening. Door
frame trims should rest evenly
on the wall
O. Check the door frame’s vertical
and horizontal placement
P. Wedge the door frame in the
construction opening
5

R. Fill the gaps between the door
frame and the construction
opening with low-pressure
caulking foam
S. After caulking foam has dried,
cut the excess off with a knife
and remove the wedges
T. In order to fasten the door
frame body better in the
construction opening, the
profile can be drilled through
at the place where it will be
covered by the trim. First by
drilling a ø4 hole through and
then a ø10 opening in the first
panel of the profile
U. Using appropriate screws/pins,
fasten profiles in the
construction opening
6

W. Insert the rear trim into the
door frame body, beginning
from the door frame bottom.
Assembly adhesive may be
used to join the trim with the
body permanently
X. Install the trim evenly in the
door frame body
Y. Correctly assembled door
frame in the opening
Z. Using screws [19] screw the
door striker plate to the door
frame profile [18]
7
19
18