LevelOne WUA-1610 User manual

WUA-1610, WUA-1610H
300Mbps Wireless USB Adapter
User Manual
V1.0

Table of Contents
Chapter 1 Introduction ...................... 1
1.1 PACKAGE CONTENTS .........................................................1
1.2PRODUCT FEATURES..........................................................1
1.3LED INDICATOR DESCRIPTION..............................................2
1.4 PRODUCT USAGE .............................................................2
1.5 BEFORE INSTALLATION .......................................................2
1.6 DISABLE OTHER MANUFACTURERS’WIRELESS NETWORK ADAPTERS .3
1.7 PRODUCT MAINTENANCE ...................................................4
1.8WORKING ENVIRONMENT ..................................................5
1.9 SYSTEM REQUIREMENTS.....................................................5
Chapter 2 Installation Guide .............. 5
2.1 HARDWARE INSTALLATION................................................6
2.2 DRIVER AND SOFTWARE INSTALLATION....................................6
Chapter 3 System configuration....... 12
3.1 GENERAL .....................................................................13
3.2PROFILE.......................................................................13
3.3LINK INFORMATION.........................................................23
3.4ADVANCED ...................................................................25
Appendix 1: FAQ .............................. 27

-1-
Chapter 1 Introduction
Thank you for choosing this LevelOne wireless adapter!
The LevelOne WUA-1610 / WUA-1610H 300Mbps Wireless USB Adapter
complies with the most advanced IEEE802.11n standards, and is also
compatible with IEEE802.11 b/g/n wireless devices. The WUA-1610 /
WUA-1610H 300Mbps Wireless USB Adapter includes an easy-to-use
configuration that discovers available wireless networks wherever you go.
1.1 Package Contents
WUA-1610 / WUA-1610H
2dBi Antenna x 2 ( WUA-1610 )
5dBi Antenna x 2 ( WUA-1610H )
USB Cable
Quick Installation Guide
CD Manual / QIG / Utility
1.2 Product Features
Upgrades your wireless network up to 300Mbps
Provides 2dBi detachable antenna (WUA-1610)
Provides 5dBi detachable antenna (WUA-1610H)
Provides Wi-Fi protected setup (WPS) configuration
Quick and easy installation
Compatible with IEEE802.11b/g/n wireless standards
Supports WEP, WPA and WPA2 encryption with IEEE 802.1X for high
level security
USB 2.0 interface
Supports Window XP/Vista/7

-2-
1.3 LED Indicator Description
There is one status LED indicator on the side of the wireless network adapter.
It lights up and stays ON when working correctly, and flashes when
transferring data.
1.4 Product Usage
The WUA-1610 / WUA-1610H Wireless USB Adapter offers a fast, reliable and
extendable solution for wireless access.
It is mostly used in the following circumstances:
1. Enables staff members who require greater mobility in the office to have
access to wireless networks anywhere inside their company.
2. Enables wireless communication for companies or places which are not
suitable for wired LAN installation because of budget or building environment
restrictions, such as historical buildings, rentals, or places for short-term
usage.
3. Suits businesses or individual who often changes network topology.
4. Suits company or individual who would like to avoid using expensive
cables or renting lines etc.
1.5 Before Installation
1. Please peruse this user manual before you install and use the product.
2. Please close or uninstall the configuration programs of other
manufacturers’ before you install the configuration programs of WUA-1610 /
WUA-1610H Mato avoid possible UI collision.
3. In order to avoid possible network collision between this LevelOne
network adapter and those of other manufactures, we recommend you to
first disable the network of other manufacturer when installaing drive.

-3-
1.6 Disable other manufacturers’ wireless network adapters
1. Right click “My Computer” and select “Manage”
2. On the Computer Management screen ,select“Device Manager” －
“Network adapters”, and right click the network adapter you want to disable
and click “Disable”

-4-
3. Click the “Yes” button on the dialogue box to disable the network adapter.
1.7 Product Maintenance
1. Please keep the product away from water and humid environment to
guarantee its normal performance
2. Protect it against hazardous substances (such as acids, alkalis etc).
3. Please don’t directly expose the adapter to the sunlight or excessive
heat.
4. Please contact LevelOne tech support if any problems occur.

-5-
1.8 Working Environment
Temperature :
Operating Temperature：0℃~40℃
Storage temperature：-20℃~70℃
Humidity :
Operating Humidity：10% ~ 90% RH (non-condensing)
Storage Humidity：5% ~ 95% RH (non-condensing)
1.9 System Requirements
►Available USB 2.0 slot
►300 MHz processor and 32 MB of memory
►CD-ROM drive
►An 802.11 b/g/n access point (for Infrastructure Mode) or another 802.11
b/g/n wireless adapter (for Ad Hoc; Peer-to-Peer networking mode.)
►Microsoft® Windows® 7, Vista™, XP
Chapter 2 Installation Guide
This chapter will guide you through the process of installing the network
adapter software package, with the included software CD. The package
integrates driver and configuration software. Thus, when you are installing
the driver, the configuration software will be installed automatically as well.
The software installation steps and operating guide in this user guide are
explained under Windows XP, Installation steps for other operating systems

-6-
are similar.
2.1 Hardware Installation
Plug the USB Wireless Adapter into an available USB port on your computer,
and the Found New Hardware Wizard (windows 7) screen will appear; Close
the wizard, then clicks the following steps to install
2.2Driver and Software Installation
Installation
1. Insert the CD into the CD-ROM drive on your PC. The autorun program should
start automatically. If it does not, please run autorun.exe under your CD-ROM
drive. In the autorun screen, click Utility to begin the software installation.
2. Click “Next” to continue.

-7-
3. Click “Next” to continue.

-8-
4. Click “Next” to continue.
5. In Windows Vista / 7, the follow message may appear. Please click “Install
this driver software anyway.”
6. Please click “Finish” and restart your computer.

-9-
7. After your computer has restarted, the Utility icon will appear in your taskbar.
Note: The red cross over the icon indicates the USB Adapter is not plugged in.
8. Now insert the Wireless USB Adapter into your computer’s USB port. The

-10-
“Found New Hardware Wizard” will appear. Follow the prompts until you
see that the Wireless USB Adapter has been successfully installed.
Note: Device installation is now complete. You can now use the Utility to connect to your
wireless network.
Connect to Wireless Network
9. Double click the LevelOne Wireless LAN Utility on your Windows desktop.
10. Click the “Site Survey” tab to scan for available wireless access points.

-11-
Double click the wireless access point you want to connect to. This will create a new Profile.
Enter the wireless encryption method and key if required. This needs to be the same as the
wireless router or access point you are connecting to.
11. Click “Next” to continue. “ ”

-12-
12. Click “Next” to continue. “ ”
LevelOne recommends WPA2-PSK (AES) for maxi-mum security.
Chapter 3 System configuration
The USB Wireless Adapter provides two modes: Station mode and Access
Point mode, the default is Station mode. You can select remote wireless AP to
connect to Internet in station mode. But in the AP mode, the wireless USB
adapter act as a wireless access point which wireless client can connect to
share an Internet connection with others.
Use the LevelOne WLAN Utility to check the link information, search for
available wireless networks, or create profiles that hold different
configuration settings. You can double-click the icon on your desktop to run it.
Another way to start the Configuration Utility is to click Start> All Programs>
LevelOne Wireless> LevelOne Wireless Utility. If the utility is not selected to
install, then you may use the utility your computer has (e.g. windows zero
config)

-13-
3.1 General
The General tab displays current Wireless statistics.
General Information
SSID: The unique name of the wireless network.
Rate: The data transfer rate of the current connection
IP Address: The IP Address of the Adapter
Mask: The Subnet Mask of the Adapter
Channel: The channel of the current connection
3.2 Profile
3.2.1. Quick Connect
If you want your wireless computers to communicate with other computers
on your wired network via a wireless access point.

-14-
Select Available Network tab and click Refresh button to refresh current
available wireless network, you can double click it after highlighting a
wireless network you want to connect, If it is encrypted, you need to enter
Network Key and confirm it and it will be OK. (Note: profile will detect the
Authentication and Encryption of current wireless network, you don’t need
to change it.)

-15-
Click to enter the encryption code.
Click to connect the wireless network.
3.2.2. Add to profile
Select a wireless network and click the “red” button to create this profile (the
following picture).

-16-
Input the profile name and select Network Type, you should select
“Infrastructure-connection to AP”, then click .

-17-
If it is encrypted, you need to enter Network Key to confirm it and then click
next.(Note: profile will detect the Authentication and Encryption of current
wireless network, you don‟t need to change it .)
You can select “Use Pre-logon Connection” and click .

-18-
The wireless network connection be added to the profile list.
3.2.3. Profile Management
Select a profile and you can delete, edit and export to computer as a
Wireless profile file.
Also you can click the “Red” button to display the Profile list.