Lexicon OMEGA Firmware update

USB Device Drivers, Cubase LE
Setup, and Pantheon™Reverb
Plug-in for Windows®XP
OMEGA STUDIO™SOFTWARE INSTALLATION GUIDE
Cubase LE Setup and
Pantheon™ Reverb Plug-in
for Mac®OS X

Congratulations on your purchase of the Lexicon Omega Studio. This guide contains the information
needed to install the required USB drivers and Steinberg’s Cubase LE recording software for use with
your Lexicon Omega hardware on either Windows® XP or Mac®OSX computer systems. Please follow
these instructions carefully to ensure smooth installation of each of these components.
OMEGA STUDIO™FOR WINDOWS®XP USERS
A. INSTALLING THE LEXICON USB DRIVERS
You must install the USB drivers to use your Lexicon Omega’s USB connection with your computer.
Follow the directions listed in the following section to complete the installation process.
1. Start your computer. Close any open programs you have running.
2. Take your Lexicon Omega hardware out of the box and plug the power in.
3. Connect the included USB cable to your computer and to the Omega.
4. You will see multiple messages pop up from the task bar indicating that your computer has found a
new USB device. There will be multiple messages because there are four USB devices in the Omega.
When Windows displays the message “Your new hardware is installed and ready to use”, Windows has
completed identifying your new hardware. However, your software installation IS NOT complete.
5. Put the Omega Studio Software Installation disk into your computer’s CD-ROM drive. If you have
Autorun enabled, the Omega Driver Installer Setup Wizard will automatically launch. If it does not
launch automatically, you can open it by selecting Start>Run and entering D:\Omega.exe
(where D:\ is the letter of your CD-ROM drive).
6. Next, select the language that you’d like to run the installer in.
7. Continue selecting Next and choose I agree to the terms of the License Agreement.
8. Select the Omega Driver Installer Software components (Cubase LE, Pantheon Reverb Plug-In, and
Help Files) that you wish to install and click Next.
9. Choose your desired installation folder, or use the default setting and select Install.
10. You will now see the window shown below. Click Next to continue and follow the onscreen
instructions for the remainder of the installation.

11. During this process you may be asked (4 times) to continue or stop the installation. Click
Continue Anyway each time as shown below.
12. Click Finish to complete the Driver Installation.
Note: If you chose to install Cubase LE in Step 8, the installation of Cubase LE will now
begin. Skip Steps 1 and 2 of the next section and continue following the rest of
the instructions to correctly install Cubase LE.
B. INSTALLING CUBASE LE RECORDING SOFTWARE
1. Start your computer. Close any open programs you have running. Put the Omega Studio Software
Installation disk into your CD-ROM drive.
2. If the disk doesn’t Autorun, you can open it by selecting Start>Run and entering
D:\CubaseNotSilient\Cubase_LE.exe(where D:\ is the letter of your CD-ROM drive) then click
OK.
3. Enter your information as directed by the Cubase LE Installer (all required fields are denoted with an
asterisk). Your Serial Number is printed on the back of the Lexicon Omega Studio Software CD case
(as shown below). Select OK to continue with the installation after you’ve entered all the required
information.
4. Follow the onscreen installation instructions as directed. You will be prompted to restart your
computer when the installation has completed.

C. SETUP WINDOWS AUDIO AND MIDI
When the Lexicon USB Audio and MIDI drivers were installed, Windows may have automatically selected
them as your default audio and MIDI outputs. This means that your Windows sounds will be sent to the
Omega rather than your computer’s sound card. We need to check if these have been changed and
return the settings to what they were before.
1. Select Start>Control Panel>Sound and Audio Devices.
2. Select the Audio tab.
3. Under Sound Playback>Default device, open the pull-down menu and make sure your
computer’s sound card is selected.
4. Under Sound Recording>Default device, open the pull-down menu and make sure your
computer’s sound card is selected.
5. Under MIDI Music Playback>Default device, open the pull-down menu and make sure your
MIDI device is selected.
D. USING CUBASE LE WITH THE LEXICON OMEGA STUDIO
1. Start Cubase LE. The first time you use Cubase LE with the Lexicon Omega Studio your may be
asked to run the Multimedia test as shown below. Select No.
2. Cubase LE will display the following warning that configuration has not been tested. Click OK.

3. Once you are into Cubase, go to Device>Device Setup.
4. Under ASIO Drivers, click on VST Multitrack and select Lexicon USB ASIO if it is not already
selected. Click on Switch to switch the driver and click OK. You are now ready to begin recording
using your Omega Studio and Cubase LE.

OMEGA FOR MAC®USERS
The Omega hardware is designed to interface directly with your Mac computer via USB using OS X’s
Core Audio drivers. This means no separate driver installation is needed as long as your Mac system
software is 10.2.8 or greater (see Apple’s website for software update information if your system software
is 10.2.8 or earlier).
A. INSTALLING CUBASE LE RECORDING SOFTWARE FOR MAC
1. Start your computer. Close any open programs you have running. Place the Omega Studio Software
Installation disk in your CD-ROM drive.
2. Double-click the Lexicon Installer CD icon when it appears on your desktop.
3. When the Lexicon Installer window opens, double-click on the Cubase LE Installer icon and then
click Continue.
4. Click Accept to agree to the terms of the Software Licensing Contract and continue.
5. Choose your desired installation folder, or use the default setting and select Install.
6. Enter your registration information as directed by the Cubase LE Installer. Your Authorization
Number is printed on the back of the Lexicon Omega Studio Software Installation CD case (as shown
below). You must include the hyphens when entering the number. Select OK to continue with the
installation after you’ve entered your name and serial number.
7. Follow the instructions of the onscreen prompts. When the installation is finished, click on Quit.
B. INSTALLING THE LEXICON PANTHEON™ FOR MAC
1. Click on the Pantheon VST Installer icon. Next, click Continue and then Install. When the
License Agreement appears, click Agree then wait for the Installer to finish and click Quit.

C. SETTING UP CUBASE LE FOR USE WITH THE OMEGA STUDIO
1. Take your Lexicon Omega hardware out of the box and plug the power in.
2. Connect the included USB cable to your computer and to the Omega.
3. Open Cubase LE, and go to Devices>Device Setup as shown below.
2. Click on VST Multitrack and select Lexicon Mac USB 1 as the ASIO Driver (as shown below).
3. Cubase LE will now ask you if you would like to switch the driver. Select Switch then OK.
4. Now, go to Devices>VST Inputs. Make each of the 4 Mac USB inputs active by clicking on the
Active buttons and close the box. (If only 2 ports are shown, expand the window to show all 4 ports.)
You are now ready to start recording with Cubase LE.

Cubase and ASIO are trademarks of Steinberg Media Technologies GmBH.
Lexicon uses the Nullsoft Scriptable Install System (NSIS) - Copyright ©1999-2004 Nullsoft, Inc.
18-0542-B
8760 South Sandy Parkway
Sandy, UT 84070
Tel: [phone]
Fax: [phone]
http://www.lexiconpro.com
Lexicon Omega Support
As new recording software becomes available, the Lexicon Omega can be updated to ensure it works properly
with these applications. Please check the Lexicon website for future update information.