Lexus LDT-2111 User manual

INSTALLATION MANUAL
LCD Desk Mount
23"
MAX
75x75
100x100
ISSUED: ARP. 2013
CAU TION: DO NOT EXCEED
RATED LISTED WEIGHT. SERIOUS
INJURY OR PROPERTY DAMAGE
MAY OCCUR!
8kgx2
(17.6lbsx2)
RATED
8kgx2
(17.6lbsx2)
RATED
11
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your distributor if you have any questions.
LDT-2111

21
NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
• Do not begin the installation until you have read and understood all the instructions
and warnings contained in this installation sheet. If you have any questions
regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• Make sure that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
• Always use an assistant or mechanical lifting equipment to safely lift and position
the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage
to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation.
If any parts are missing or faulty, telephone your local distributor for a replacement.
Package P
Package Mx2
M4x14 (x4)
M-A
M5x14 (x4)
M-B
D5 washer (x4)
M-C
4mm Allen key
P-B
(x1)3mm Allen key (x1)
P-A
base plate (x1)
P-C
pad (x1)
P-D
adapter bracket
assembly (x2)
A
desk clamp (x1)
E
cable clip (x2) screw (x2)
Package
bottom pole (x1)
B
top pole (x1)
C
co nector n (x1)
D

4
34 3
3. Assembling the Pole and Desk Clamp
collar loosen
tighten
tighten
P-A
P-A
P-A
B
P-A
P-A
loosen
tighten
adjust height
1. Installing the Cable Clips
4. Attaching to the Desk
4a. Edge Installation
tighten
Turn the knob to make clamp fit to desk edge, then secure it tightly.
Note: min. desktop thickness=10mm
max. desktop thickness=90mm
2. Removing the VESA Plates
P-A
P-A
articulated arm assembly VESA Plate

65
collar
B
D
C
tighten
tighten
5. Installing the Articulated Arm Assembly
Insert the articulated arm
assembly into the pole untill
it touches the collar.
tighten
Note: Plastic handle can
be pulled out due to a
limited amount of space.
adjust handle
4. Attaching to the Desk
4b. Hole Installation
rubber pad
base plate attach screw
P-B
pad
adjust screw
Note: min. hole diameter =10mm
max. hole diameter =70mm
Disassemble the desk clamp and select the right parts for using hole installation.
Re-install the base plate with three retained screws, then tighten securely.
Insert the adjust screw into base plate through the hole. Then using the adjust screw to fix and tighten it securely.

87
7. Installing the Displays
Insert the VESA plate onto the mount and use the previously removed screws to secure them. Make sure
the display is safely secured before finally releasing.
Tighten all screws but do not over tighten.
Screw the VESA plate onto the display.
TV
TV
TV
M-A
M-B
M-C
6. Installing the VESA Plates
Top of the display
P-A

910
+15°
-15°
9. Adjustment
Adjust to the desired position or tilt.
180°
P-B
Slightly loosen or tighten the
screws as required due to
different weights of the displays.
8. Cable Management
Use clips for routing the cables.
Note: Leave slack in the cable for arm movement.
360°