LG 47LC7D User manual

eooa
LCD TV I PLASMA TV
OWNER'S MANUAL
LCD TV MODELS
32LB9D
47LC7DF
PLASMA TV MODELS
60PY3D
Please read this manual carefully before operating your set.
Retain [t for future reference.
Record mode[ number and serial number of the set.
See the [abe[ attached on the back cover and quote this
information to your dealer when you require service.
ENERGY STAR is a set of power-saving
guidelines issued by the U.S.
Environmental Protection Agency(EPA).
As an ENERGY STAR
Partner LGE U.S.A.,
Inc. has determined
that this product
meets the ENERGY
STAR guidelines for
energy efficiency.

WARNING /CAUTION
WARNING /CAUTION
To prevent fire or shock hazards, do not expose
this product to rain or moisture.
WARNING/CAUTION
TO REDUCE THE RISK OF FIRE AND ELEC-
TRIC SHOCK. DO NOT EXPOSE THIS PRO-
DUCT TO RAIN OR MOISTURE.
Class B digital device
This equipment has been tested and found to com-
ply with the bruits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio fre-
quency energy' and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference wi[[ not
occur in a particular installation, if this equipment
does cause harmful interference to radio or televi-
sion reception, which can be determined by turning
the equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- increase the separation between the equipment
and receiver.
-Connect the equipment to an outlet on a circuit
different from that to which the receiver is con-
nected.
-Consuff the deaJer or an experienced radio/TV
technician [-or help.
Any changes or modifications not express[)'
approved by the party responsible for compliance
couJd void the user's authority to operate the
equipment.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV sys-
tem installer's attention to Article 820-40 of the
National Electric Code (U.S.A.). The code pro-
vides guidelines for proper grounding and. in
particular, specifies that the cable ground shall
be connected to the grounding system of the
building, as close to the point of the cable entry
as praci_caL
Do not attempt to modify this product in any way
without written authorization from LG Electronics.
Unauthorized modification could void the user's
authority to operate this product

SAFETY INSTRUCTIONS
IMPORTANT SAFETYINSTRUCTIONS
Important safety instructions shall be provided with each apparatus. This information shall be given in a se-
parate booklet or sheet, or be located before any operating instructions in an instruction for installation for
use and supplied with the apparatus.
This information shall be given in alanguage acceptable to the country where the apparatus is intended to
be used.
The important safety instructions shall be entitled "Important Safety Instructions': The following safety
instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safe-
ty information may be included by adding statements after the end of the following safety instruction list. At
the manufacturer's option, a picture or drawing that illustrates the intent of a specific safety instruction may
be placed immediately adjacent to that safety instruction :
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
O Do not use this apparatus near water
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordancewith the manufacturer'sinstructions.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other appa-
ratus (including amplifiers)that produce heat.
0Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong, The wide blade
or the third prong are provided for your safe-
ty. If the provided plug does not fit into your
outlet, consult an electrician for replacement
of the obsolete outlet.
OProtect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit
from the apparatus.
Only use attachments/accessories specified
by the manufacturer.
2

0Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
O Unplug this apparatus during lightning storms
or when unused for long periods of time.
O
Refer all servicing to qualified service person-
nel. Servicing is required when the apparatus
has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the
apparatus, the apparatus has exposed to rain
or moisture, does not operate normally, or has
been dropped.
CAUTION concerning the Power Cord :
Most appliances recommend they be placed
upon a dedicated circuit; that is, a single out-
let circuit which powers only that appliance
and has no additional outlets or branch cir-
cuits. Check the specification page of this
owner's manual to be certain.
Do not overload wall outlets. Overloaded wall
outlets, loose or damaged wall outlets, exten-
sion cords, frayed power cords, or damaged
or cracked wire insulation are dangerous. Any
of these conditions could result in electric
shock or fire. Periodically examine the cord of
your appliance, and if its appearance indicates
damage or deterioration, unplug it, disconti-
nue use of the appliance, and have the cord
replaced with an exact replacement part by an
authorized servicer. Protect the power cord
from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a
door, or walked upon. Pay particular attention
to plugs, wall outlets, and the point where the
cord exits the appliance.
Outdoor Use Marking :
WARNING - To Reduce The Risk Of Fire Or
Electric Shock, Do Not Expose This Appliance
To Rain Or Moisture
Wet Location Marking : Apparatus shall not be
exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall
be Dlaced on or over apparatus.
GROUNDING
Ensure that you connect the earth ground
wire to prevent possible electric shock. If
grounding methods are not possible, have a
qualified electrician install aseparate circuit
breaker.
Do not try to ground the unit by connecting
it to telephone wires, lightening rods, or gas
pipes.
Power Supply
DISCONNECTING DEVICE FROM MAINS
Main plug is the disconnecting device. The
plug must remain readily operable.
3

CONTENTS
WARNING /CAUTION ........................... 1
SAFETY INSTRUCTIONS ..........................2
FEATURES OF THIS TV ................ 6
PREPARATION
Accessories .............................. 7
Front Panel Controls ...................... 8
Back Panel Information ................... 10
Attaching the TV to a Wall ................. 12
Attaching the TV to a Desk ................ 12
Stand Installation ........................ 13
Back Cover for Wire Arrangement ........... 14
Desktop Pedestal Installation ............... 17
VesaWall Mounting ....................... 17
Not usingthe desk-typestand ................ 18
Swivel Stand ............................. 18
Antenna or Cable Connection .............. 19
EXTERNAL EQUIPMENT SETUP
HD Receiver Setup ......................................... 20
DVD Setup ..................................................... 23
VCR Setup ...................................................... 25
Other A/V Source Setup ................................. 27
PCSetup ........................................................ 28
USB In Setup .................................................. 54
Audio Out Setup ............................................. 55
T
WATCHING "I'V/CHANNEL CONTROL
Remote Control Functions .................. 36
Turning on TV ........................... 58
Channel Selection ....................... 39
VolumeAdjustment ...................... 40
On-Screen Menus Selection ................ 41
Channel Setup
- Auto Scan ( Auto Tuning) .............. 42
- Add /Delete Channel ( Manual Tuning) .. 43
- Channel Editing ....................... 44
Input List ............................... 45
SimpLink ............................... 46
Input Label ............................. 48
Entry Modes ............................ 49
Photo List .............................. 50
Music List .............................. 54
PICTURE CONTROL
Picture Size (Aspect Ratio) Control .......... 56
Preset Picture Settings
- Picture Mode - Preset ................ 58
- Color Tone - Preset ................... 59
ManualPictureAdjustment
- Picture Mode - User Mode ............ 60
- Color Tone - User Mode ............... 61
XD - PictureImprovementTechnology........... 62
Advanced - Cinema 3:2 Pulldown Mode ...... 63
Advanced - Black(Darkness) Level .......... 64
Picture Reset ............................ 65
ImageStickingMinimization(ISM)Method ....... 66
Low-Power Picture Mode .................. 67
SOUND &LANGUAGE CONTROL
Auto Volume Leveler ( Auto Volume) ......... 68
Preset Sound Settings( Sound Mode) ........ 69
Sound Setting Adjustment - User Mode ........ 70
Balance ................................. 72
Stereo /SAP Broadcast Setup .............. 73
TV Speakers On/Off Setup ................ 74
Audio Language ......................... 75
On-Screen Menus Language Selection ....... 76
Caption Mode
- Analog BroadcastingSystemCaptions .... 77
- Digital Broadcasting System Captions ...79
- Caption Option ..................... 80
4

TIME SETTING
Clock Setting
- Auto Clock Setup ................... 81
- Manual Clock Setup .................. 82
Auto On/OffTime Setting ................. 83
Sleep Time Setting ........................ 84
Auto Shut-off Setting ..................... 85
Z_ ¸ _ 7 =7_Z _ 7_ =_ _ _:_ _...... _ _
PARENTAL CONTROL/RATINGS
Set Password& Lock System ............... 86
Channel Blocking ........................ 88
Movie & TV Rating ....................... 89
External Input Blocking .................... 92
Key Lock ............................... 92
APPEND IX
Troubleshooting .......................... 93
Maintenance ............................ 95
Product Specifications .................... 96
Programming the Remote Control .......... 97
IR Codes .............................. 101
External Control through RS-232C ......... 103
5

FEATURESOF THIS TV
What is a Plasma TV ?
Using plasma is the best way to achieve flat panel
displays with excellent image quality and large screen
sizes that are easily viewable. The Plasma TV can be
thought of as a descendant of the neon lamp and or
a series of fluorescent lamps.
How does it work?
Plasma TV is an array of cells, known as pixels, which
are comprised of three sub-pixels, corresponding to
the colors red, green, and blue. Gas in a plasma state
is used to react with phosphors in each sub-pixel to
produce colored light (red, green, or blue). These
phosphors are the same types used in Cathode Ray
Tube (CRT) devices such as televisions and common
computer monitors.
Plasma TV offers a rich, dynamic display because
each sub-pixel is individually controlled by advanced
electronics to produce over 16 million different col-
ors. This means that you get perfect images that are
easily viewable in a display that is fewer than five
inches thick.
160 ° -Wide angle range of vision
Your flat panel plasma screen offers an exceptionally
broad viewing angle of over 160 degrees. This means
that the display is clear and visible to viewers any-
where in the room.
Wide Screen
The wide screen offers a theater-like experience in
your own home.
Multimedia
Connect your plasma display to a PC and use it for
conferencing, games, and Internet browsing. The
Picture-in-Picture feature allows you to view your PC
and video images simultaneously.
Versatile
The light weight and thin size makes it easy to install
your plasma display in a variety of locations where
conventional TVs do not fit.
The Plasma TV Manufacturing Process: afew
minute colored dots may be present on the
Plasma TV screen
The PlasmaTV is composed of 0.9 to 2.2 million
cells. A few cell defects will normally occur in the
Plasma TV manufacturing process. Several tiny,
minute colored dots visible on the screen should be
acceptable. This also occurs in other Plasma TV
manufacturers' products. The tiny dots appearing
does not mean that this Plasma TV is defective. Thus
a few cell defects are not sufficient cause for the
Plasma TV to be exchanged or returned. Our pro-
duction technology minimizes these cell defects dur-
ing the manufacture and operation of this product.
Cooling Fan Noise (This feature is not available for all models.)
In the same way that a fan is used in a PC computer
to keep the CPU (Central Processing Unit) cool, the
Plasma TV is equipped with cooling fans to cool the
Monitor and improve its reliability. Therefore, a cer-
tain level of noise could occur while the fans are
operating and cooling the Plasma TV.
The fan noise doesn't have any negative effect on
the Plasma TV's efficiency or reliability. The noise
from these fans is normal during the operation of
this product. We hope you understand that a certain
level of noise from the cooling fans is acceptable and
is not sufficient cause for the Plasma TV to be
exchanged or returned.
FOR LCD TV
If the TV feels cold to the touch, there may be a
small "flicker '_when it is turned on. This is normal,
there is nothing wrong with TV.
Some minute dot defects may be visible on the
screen, appearing as tiny red, green, or blue spots.
However, they have no adverse effect on the moni-
tor's performance.
Avoid touching the LCD screen or holding your fin-
ger(s) against it for long periods of time. Doing so
may produce some temporary distortion effects on
the screen.
On Disposal
a, The fluorescent lamp used [n this product con-
rains a small amount of mercur_:
b, Do not dispose of this product wffh genera[
household waste,
c, Disposal of this product must be carded out [n
accordance to the regulations of your local
authorffy,
6

PREPARATION
ACCESSORIES
Ensure that the following accessories are included with your plasma display. If an accessory is missing, please
contact the dealer where you purchased the product.
User must use shielded signal interface cables (D-sub 15 pin cable) with ferrite cores to maintain standard
compliance for the product.
_o
m
_o
z
Owner's Manual Batteries CD Manual Remote Control
Power Cord Polishing Cloth
_ Slightly wipe stained spot on the exterior only with the polishing
cloth for the product exterior if there is stain or fingerprint on
surface of the exterior.
_ Do not wipe roughly when removing stain. Please be cautions of
that excessive power may cause scratch or discoloration.
75f_ Round Cable 2- TV Bracket Bolts 2- TV Brackets,
2- Wall Brackets D-sub 15 pin Cable
01"
Cable Management Twist Holder
Arrange the wires with the twist holder, ii/iiii/iillilii,iii!ii!,iiiilil_!_i_i!_ii!_i
/iiiiiiii
(Refer to p. 18)
Additional Cover 3- Bolts 2 - Rubber
7

FRONT PANELCONTROLS
m
z
_ Here shown may be somewhat different from your TV.
_ If your TV stand has a protection film, remove it attached to the stand. Then wipe the stand with polishing
cloth.
60PY3D
Remote Control Sensor
Program Display Touch Pad
Power Standby Indicator
• illuminates red in standby
mode.
• illuminates green when
the set is switched on.
ENTER
Button VOLUME
POWER MENU (@,_)
Button Button Buttons
CHANNEL
(T,A)
Buttons
8

47LC7DF
Intelligent Eye
Adjusts picture
according to the
surrounding con-
ditions. Remote Control Sensor
(V,A) Buttons
VOLUME
(_II,I_) Buttons
ENTER Button
Button
INPUT Button
POWER Button
Power/Standby Indicator
• illuminates red in standby mode.
• illuminates green when the set is switched on.
_D
r_
_D
z
32LB9D
Intelligent Eye
Adjusts picture
according to the
surrounding con-
ditions.
Remote Control
Sensor
(V,A) Buttons
VOLUME
(_,_) Buttons
Button
Button
Button
Button
Power/Standby Indicator
• illuminates red in standby mode.
• illuminates green when the set is switched on.
9

BACK PANELINFORMATION
_o
_o
z
_ Here shown may be somewhat different from your TV.
60PY3D
Input port
-- S-VIDEO Input
Connect S-Video out from an
S-VIDEO device.
'/VIDEO Input
Connect audio/video output from
an external device to these jacks.
47LC7DF
_USB Input
_S-VIDEO Input
Connect S-Video out from an S-
VIDEO device.
_AUDIO/VIDEO Input
Ut Connect audio/video output from
an external device to these jacks.
10

_ Here shown may be somewhat different from your TV.
32LB9D
Input port
,/VIDEO Input
Connect audio/video output from
an external device to these jacks.
_o
m
_o
z
IANTE"N®J--
CABLEIN _ ]
AUDIO
RGB(PC) (RGB/DVI)
Y PB PR
...........VIDEO AUDIO -J S-VIDEO VIDEO LIMO_O)-AUDIO-R
@ HDMI/DVI IN
Connect a HDMI signal to 1,2 or 3.
Or DVI (VIDEO)signal to the 1,2 or 3 port
with a DVl to HDMI cable.
@ COMPONENT IN
Connect a component video/audio device to
these jacks.
_ RGB(PC)
AUDIO (RGB/DVI)
Connect the monitor output from a PC to the
appropriate input port.
_ RS-232C IN (CONTROL & SERVICE)PORT
Connect to the RS-232C port on a PC.
(j_ REMOTE CONTROL PORT
Connect your wired remote control.
Q AV (Audio/Video) IN 1
Connect audio/video output from an external
device to these jacks.
S-VIDEO
Connect S-Video out from an S-VIDEO device.
@
O
AUDIO OUT
Connect analog audio to various types of
equipment.
DIGITAL AUDIO OUT
Connect digital audio to various types of
equipment.
Note: In standby mode, these ports do not work.
_ ANTENNA/CABLE IN
Connect over-the air signals to this jack.
Connect cable signals to this jack.
_ Power Cord Socket
For operation with AC power.
Caution :
Never attempt to operate the TV on DC power.
11

_D
m
_D
z
ATTACHING THE TV TO A WALL
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,
potentially causing injury or damaging the product.
Caution: Please make sure that children don't climb on or hang from the TV.
_ Here shown may be somewhat different from your TV.
60PY3D 47LC7DF
I32 LB9 D 1
_ Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
_lnsert the eye-bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately ) to
the wall. Match the height of the bracket that is mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
_ Use a sturdy rope (not provided as parts of the
product, must purchase separately) to tie the
product. It is safer to tie the rope so it becomes
horizontal between the wall and the product.
ATTACHING THE TV TO A DESK(O.ly32LB9Dmodel)
We recommend that the TV be t_ached to desk so it cannot be pulled in a forward/backward direction,
potentially causing injury or damaging the product.
_iiiii_i_i_i_i_i_iii_!!_!!_i_i_i_i_i_i_i_i_i_i_!_i_!i_iiii_iiii_iii_iii_i_iiiiiiiiiiiiii_ii_i!!i_ii
2-Bolts
(not provided as parts of
the product, must purchase
separately)
Stand
Deck
_ This appar tus must be securely ttached to the floor/wall per installation
instructions.Tipping,shaking, or rocking the machine may cause injury!death,
12

STAND INSTALLATION (Only32LB9Dmodel)
0Carefully place the product screen side down on
acushioned surface that will protect product and
screen from damage.
-0
po
m
po
z
e ssemble the product stand with the product as
shown.
Install the 4 bolts securely, in the back of the
product in the holes provided.
13

BACK COVERFORWIRE ARRANGEMENT
_ Here shown may be somewhat different from your TV.
_o
m
_o
z
60PY3D
O Hold the CABLE MANAGEMENT with both handsand pull it as shown.
45 °
CABLE MANAGEMENT
Connect the cables as necessary.
To connect an additional equipment, see the External equipment Connections section.
Install the CABLE MANAGEMENT as shown.
14

_ Here shown may be somewhat different from your TV.
47LC7DF
0Connect the cables as necessary.
To connect an additional equipment, see the
External equipment Connections section.
_o
m
_o
z
O Install the CABLE MANAGEMENT as shown.
CABLE MANAGEMENT
O undle the cables using the supplied twist
holder. iii!"!_i'ili!i'i_i_iiili_!_Xi'iii_'ii!i!i!i'i_'ii!iiiil!iii!!_!i_i'i!!!!_i!'!!!ii!!i!i_iliJliii_ii_i!!i!
iililiiiiii!i!i!i!i!i!i!i!i!i_ii_iiiiii_i_i_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_iiii!iiiiii!iii!i!!i! iiiiiiiiiiiiiiiiiiiiiiiiiiiiii!!_!_
_iiiiiiiJiii_iiiiiiii/iiiiiiiiiiiiiiiiiiiiiiiii_i_i_i_i_!_!_i_!_!_!_!_!_!_!!!!!!!_ii!i!!i!!i!!i!iiiiiiiiiiii!¸¸,/
How to remove the cable management
\
TWISTHOLDER
Hold the CABLE MANAGEMENT with both
hands and pull it upward.
, If the product is dropped, you maybe injured or the product may be broken,
1S

_o
m
_o
z
_ Here shown may be somewhat different from your TV.
32LB9D
OConnect the cables as necessary.
To connect an additional equipment, see the
External equipment Connections section.
O nstall the CABLE MANAGEMENT as shown.
(Insert it as pushing the loops on the both
sides of the cable management.)
CABLE MANAGEMENT
O undle the cables using the supplied twist
holder.
How to remove the cable management TWIST HOLDER
Hold the CABLE MANAGEMENT with both
hands and pull it upward.
(Pull it out as pushing the loops on the both sides of
the cable management.)
,If the product is dropped, you may be injured or the product may be broken,
16

DESKTOP PEDESTALINSTALLATION
For proper ventilation, allow a clearance of 4 in. on each side and the top, 2.36 in. on the bottom, and 4 in.
from the wall.
60PY3D
/
32LB9D
4inches
I
4 inches
4 inches
4inches
4 inches
/
47LC7DF
I4inches
4inches
I
4 inches
_D
m
_D
6
z
VESAWALL MOUNTING
This product accepts a VESA-compliant mounting interface pad. (optional)
There 4 threaded holes are available for attaching the bracket.
60PY3D
600ram
Ii
47LC7DF
600mm
400ram
32LBgD
200ram
lOOmrn
b, Screw length needed depends on the wa!l mount used. For further informati0n, refer to the VESA
Wall M0unting !nstructi0n Guide,
17

NOT USING THE DESK-TYPESTAND(o.'y60PY3D model)
z
_ It is applied to when installing only the 60PY3D model as wall-type.
When not using the desk-type stand, install the
supplied desk-type stand fixture protection rubber
caps as shown at the figure.
RUBBER
BOLT
ADDITIONAL COVER
To prevent the foreign materials from entering the
desk-type stand fixture, fix the desk-type stand fix-
ture protection cover(additional cover) by using
the supplied bolts as shown at the figure.
SWIVELSTAND (o.ly60PY3D model)
After installing the TV, you can adjust the the TV set manually to the left or right direction by 20 degrees to
suit your viewing position.
@ Before adjusting the angle, you must remove
the cable management and loosen (to the
left) the shaft bolt on the middle of stand's
back. And when stand be level with TV. you
must close (to the right) the shaft bolt to
set the hole.
18

ANTENNA OR CABLECONNECTION
1. Antenna (analog or digital)
Wall Antenna Socket or Outdoor Antenna without a
Cable Box Connections. For optimum picture quality,
adjust antenna direction if needed.
rMulti-family Dwellings/Apartments
Wall onnect to wall antenna socket)
Antenna
!Antenna .................
I(VHF, UHF) Single-family Dwellings/Houses
/(Connect to wall jack for outdoor antenna) ICopper Wire
IBe careful not to bend the bronze wire
lwhen connecting the antenna ...........................
2. Cable
_o
m
_o
7
Cable TV
Wall Jack
3. Using both cable and antenna
Antenna
RFCoaxial Wire (75 ohm)
Cable TV
Wall Jack
Diplexer
(Signal
Combinner)
UHF
Antenna
_ To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
_If the antenna needs to be split for two TV's, install a2-Way Signal Splitter.
If the antenna is not installed properly, contact your dealer for assistance.
_ NOTE _ The TV wil!!et you know when the analog, cable! and djgita! channel scans are comPlete_
19