LG AW-52LG50MS User manual
A
AW
W-52LG50MS
-52LG50MS
A
AW
W-60PG60MS
-60PG60MS
LSW600A
LSW600A
Bolts for guide spacer
AW-52LG50MS(M6X30)-4
AW-60PG60MS(M8X35)-4
LSW600A(M8X25)-4
4 Guide Spacer
4 Protection
cushion
Bolts for tilt wall
mounting bracket
AW-52LG50MS-6
AW-60PG60MS-8
LSW600A-8
Wall Anchor Bolt
Sleeves
AW-52LG50MS-6
AW-60PG60MS-8
LSW600A-8
2 Safety clip
Accessories
Slim tilt wall mounting bracket
Installation and
Setup Guide
RF Cable
* Only AW-52LG50MS
PC Cable HDMI CableCables for external
devices
* Only
AW-60PG60MS
After reading this manual, keep it in an easy to reach place.
- Qualified service technician should install the product properly after reading this manual thoroughly.
- Qualified service technician should hand this manual over to the customer after installation and ask him/her to
read and keep it.
Safety Instructions
Safety Instructions
WARNING
Do not install this product by yourself. Contact the
service technician qualified by the manufacturer.
It may cause injuries.
Do not install this product on a place where it cannot
be supported securely.
It may cause the product to fall and could cause injuries.
Contact the qualified service technician for
moving or replacing this product after installing.
Installing the product needs specified technical personnel, it
may cause safety problem to move or install it by yourself.
When mounting a TV on the wall, make sure not
to install TV by the hanging power and signal
cables on the back of the TV.
It may cause a fire or could give an electric shock.
Do not hang onto or impact on to this product.
It may cause the product to fall and could cause injuries.
ENGLISH
NOTES
Be sure to follow these instructions when installing
this product.
Otherwise it may cause serious injuries or damage of the product.
When drilling use drill and drill bit specified by
the manufacturer. And the depth of the hole
should meet the specifications.
Otherwise it may cause a safety problem.
Do not place a heat source (radiator or heater) or a
humidifier under the installed product.
It may cause a fire or could give an electric shock.
Make sure to unplug before installing this product.
Otherwise it may cause a fire or could give an electric shock.
Do not install this product near a sprinkler, a
sensor, a high voltage electric line, any power
source or the place where impact or vibration
can affect it.
Do not install this product barehanded.
It may cause injuries.
Two adults are needed when installing this product
and adjusting the height.
Otherwise, serious injury or product damage can occur.
Before installing, check whether the material of wall
satisfies the specifications and make sure to use
enclosed anchors supplied with the product.
Otherwise it may cause a safety problem.
Please only use the cables provided when connecting
it to the product. Using other cables will create friction
with the walls, possibly resulting in damage to the
walls or product.
Installation
Installation
1
Guide Spacer Install
- When attaching the guide spacer if bolts are loose verify bolts assembly depth one more time and refer to the
service manual.
<Work method>
1. If there are already bolts in the TV, remote them.
2. Insert the guide spacers (1) and then the bolts (2).
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
s At this time, tighten the bolt to more than 35kgf∙cm of torque.
Guide Spacer
bolts for guide spacer
(AW-52LG50MS-M6X30
AW-60PG60MS-M8x35)
LSW600A-M8X25)
ENGLISH
2
Installing Anchors
- Using the hole-drilling template provided, mark the positions of the anchor holes shown on the drawing in the
wall; using a centre-punch or other device to clearly identify the 10 drill hole positions.
Note: It is advisable to use a bubble level to make sure that the template is horizontally true.
- Warning: The surface that the tilt wall mounting bracket is to be mounted on should be of sufficient strength to
support the weight of the monitor and speakers typically; concrete, strong/weak natural rock, brick and hollow
block.
- Warning: Plasterboard is not a sufficiently strong enough material; unless the bolts are anchored into standard
construction type studs capable of supporting the weight of the monitor and speakers. If you can not
determine the strength of the material, each drilled hole should be capable of supporting a normal stress level
of 70kgf (686N) and shear stress 100kgf (980N).
Keep these instructions for future reference
Keep these instructions for future reference
a b
d
e
a. Using an 8mm drill appropriate for the material on the wall, drill each hole to a depth of 80mm/3.15inches –
100mm/3.94inches.
b. Clean each drilled hole.
c. Insert an anchor supplied with the tilt wall mounting bracket into each hole.
d. Mount the tilt wall mounting bracket on the wall. And push the guide control part upward.
e. Assembled in holes carefully. At this time, tighten the bolt to over 45kgf∙cm of torque.
Bolts for tilt wall mounting bracket
c
Anchor
3
A
Attaching the Wall Bracket
If it’s not possible to use the indicated bolt holes,
use the closet ones. Don’t go more than two
away from the indicated position.
AW-52LG50MS Model
Wall mounting equipment will be set up based in
VESA 800X400 regulation.
Fix the upper right and left side with two bolts
each, and fix the bottom right and left side with
one bolt each.
AW-60PG60MS / LSW600A Model
Wall mounting equipment will be set up based in
VESA 600X400 regulation.
Fix the right and left side with two bolts each.
< Fixing Bolts >
When mounting a bracket in a place other than the
designated wall, fix it to the concrete inside the finishing
materials with long bolts and nuts as shown in the
illustration. Bolts and nuts in the illustration are sold
separately.
<When mounting in other than the designated wall>
AW-52LG50MS
ENGLISH
4
How to connect a bracket with the product/adjust horizontal level
< How to connect the wall mount supporter and product >
Work in the order of figure
1. Carefully lift up the product and place it in position on the tilt wall mounting bracket securely as shown by arrow 1.
2. When adjusting the horizontal level, use the safety ring provided by pressing it slightly to in the direction as illustrated.
(See number in the illustration.)
There is a risk of the product falling when the safety ring is not used as shown in the illustration.
Pull the bottom of the TV/Monitor to affirm that it is firmly fixed.
See A above,be sure to lift a product/speakers assembly by the product only, do not lift using only the speakers.)
<
Horizontal level adjustment
>
If the product leans to one side, adjust the tilt with bolt 3 (M5x20). The product tilt is changed according to bolt’s
rotation direction.
- Always have more than 2 people hold the product for installation.
* Connecting the wall mount
bracket and safety clip
Safety clip
5Tilt Angle Adjustment
Use both hands when adjusting the angles. Do not place the hands on the TV’s back side or the wall mount
while adjusting. If could cause injury.
Two adult people who are capable of adjusting the tilt angle to need excessive force.
When adjusting the number
angle of the product, you must use both hands and then you can adjust the angle
as shown above.
When adjusting the number
angle of the product, you must use both hands and then you can adjust the angle
as shown above.
When adjusting the number
angle of the product, you must use both hands and then you can adjust the angle
as shown above.
When adjusting the number
angle of the product, you must use both hands and then you can adjust the angle
as shown above.
- The tilt angle can be adjusted after installation and setup.
- When you adjust the angle, hold the product carefully with both hands to avoid any damage to the product or wall.
*
The above numbers are the maximum allowed, some models may do less.(Upper picture explains the features available on
the 60 inch Plasma.)
ENGLISH
6
How to adjust height
It is possible to move the set upward and downward by as much as 80mm.
Please use both hands when adjusting the set upward and downward. Do not forget to remove the bolts on both sides of the set
before adjusting the height. Anchor the bolts again after height adjustment.
Use 14~55kgf of power when adjusting the set upward or downward.
AW-52LG50MS / AW-60PG60MS :
Two adults are needed when installing the product and adjusting the height.
LSW600A : Three adults are needed when installing the product and adjusting the height.
Otherwise, serious injury or product damage can occur.
7How to adhere the protection cushions and arrange cables
Use the protection cushions to reduce shock between the wall and TV/Monitor.
Arrange the cable like shown. You can purchase the cable holder separately or use it provided like accessory of
the TV/Monitor get.
protection
cushion
Please use only the provided PC cable, HDMI cable, and correct cables for external devices. They are optimized for this slim wall mounting.
Cables for slim wall mounting have a shorter end than that of common cables. This protects the TV such that the cables do not reach the wall
when TV is pushed to the wall.
Only use the coaxial lines and power cords provided with the TV.
When using coaxial cables other than provided, connect by using a jack shaped as '' , sold separately.
Please contact the agency or an LG Service Center if you wish to purchase extra cables for slim wall mounting.
Use the provided cables and connect them to the terminal backside. For detailed information on this, please refer to the user
guide provided with the TV.
HDMI Cable / PC Cable / Cables for external devices / RF Cable
.
ENGLISH
Dimension
Cable specification for Slim wall mounting bracket
Cable specification for Slim wall mounting bracket
Cable name
Specification
Total length (m)
Head length (mm)
HDMI cable
Ver. 1.3, 19 pin
2
28
PC cable
15 pin
2
25
Component cable
N/A
2
20
[ unit : mm ]
< AW-52LG50MS >
.
Specifications
Specifications
[ unit : mm ]
< AW-60PG60MS / LSW600A >
AW-52LG50MS
858 / 33.78
465 / 18
25 / 1
6.9 / 15.2
8.4 / 18.5
800 X 400
AW-60PG60MS
LSW600A
658 / 26
465 / 18
25 / 1
6.3 / 13.8
7.7 / 17
600 X 400
Model
Width(mm/inch)
Height(mm/inch)
Depth(mm/inch)
Weight
(kg/pound)
Weight with packing
(kg/pound)
Wall mount Vesa
specification
This manual suits for next models
2
Other LG Rack & Stand manuals
Popular Rack & Stand manuals by other brands
Premier Mounts
Premier Mounts PSD-EB installation manual
Vertiv
Vertiv KMMLED156 Quick installation guide
Vivo
Vivo STAND-TV22B instruction manual
BIN WAREHOUSE
BIN WAREHOUSE JAN21 Assembly instructions
GeoSlam
GeoSlam ZEB CRADLE Unboxing and setup instructions
Hammond Manufacturing
Hammond Manufacturing HWM Series instructions
