Vertiv KMMLED156 User manual

KMMLED156 RACK MOUNT 15.6”
CONSOLE TRAY FOR DELL EMC
Quick Installation Guide
590-2130-501A 1
The KMMLED156 console tray
assembly is provided with a pair of
slide-rail assemblies, a keyboard,
display, slide tray, Cable
Management Arm (CMA), inner
slide rails on the slide tray and an
installed VGA cable. An uninstalled
DisplayPort cable is also provided.
INSTALLATION
The slide-rail assemblies are
marked L for the left-rail assembly
and R for the right-rail assembly.
The front end of each assembly is
marked FRONT to ensure proper
installation in the rack.
CAUTION: If you are installing
more than one unit concurrently,
keep the outer slides matched with
the inner slides, which are mounted
on the slide tray. Rails and slide
trays that ship together must be
paired together. Mismatched pairs
may result in damage to the slide-
rail assemblies, slide tray or rack
cabinet.
1. Installing the slide-
rail assemblies into a
standard EIA rack
NOTE: The slide-rail mounting
mechanism has two spring-
loaded pins at each end of the
rail assemblies that retract. The
pins fit 10-32 threaded holes or
EIA-standard square- or round-
hole racks. The spring-loaded
pins self-adjust to adapt to the
rack hole configuration. Each
set of spring-loaded sleeves is
equipped with release tabs to
pull and disengage the slide-rail
assembly.
Align the two back spring-
loaded pins of the slide-rail
assembly with corresponding
holes on the rack and pull to
secure.
Extend the rail assembly to the
appropriate length of the rack.
Expandable Rack Rail Assemblies
Slide-Rail Assembly Installation (Square Hole Configuration Shown)
Spring-loaded
pins
Back of
release tab
KMMLED156 Rack Mount Console Tray

KMMLED156 RACK MOUNT 15.6” CONSOLE TRAY FOR DELL EMC
Quick Installation Guide
2 590-2130-501A
Align the two front spring-
loaded pins of the slide-rail
assembly with the
corresponding holes on the
rack and push to secure. The
release tabs click to indicate
the pins are fully engaged.
Repeat the steps for the rail on
the opposite side of the rack.
2. Attaching the end caps
and covers to the front
rail ends
NOTE: The end caps can be
installed at any time during the
assembly of the console tray.
CAUTION: The end cap’s post
sheath and end cap post are
o-center. Do not seat the end
cap or end cap cover until you
determine if the sides are flush.
Loosely insert the end cap’s
post sheath into the middle hole
of the front rail end. Determine if
the sides of the cap are flush
with the sides of the rail end
before the final seating of the
cap. If necessary, rotate the end
cap 180° to achieve proper
alignment.
Once aligned, push to seat the
end cap.
Loosely insert the end cap
cover’s post into the sheath on
the end cap. If necessary, rotate
the end cap cover 180° to
achieve proper alignment.
Once aligned, push to seat the
end cap cover. Repeat for the
second end cap.
3. Preparing for slide-tray
installation
Unlock and fully extend the
outer slide rails by pressing their
latch release.
With the outer slide rails fully
extended, verify their inner
bearing race is slid fully forward
and seated into the plastic
bearing race clip.
CAUTION: To avoid damage to
the slide rails, the outer slide
members must be fully
Outer Slide Rail Extension
Rack upright
Outer slide rail
latch release
Outer slide rail
Rack slide rail
Inner race bearing
DISENGAGED from
bearing race clip
Inner race bearing
ENGAGED with
bearing race clip
Inner race
bearing
Bearing
sleeve
Bearing
race clip
Ball Bearing Race and Clip Components
End cap
End cap
cover
Front end
of rail
End Cap Installation
Post

KMMLED156 RACK MOUNT 15.6” CONSOLE TRAY FOR DELL EMC
Quick Installation Guide
590-2130-501A 3
extended. Also, the ball-bearing
races must be in the forward
most position and engaged with
the bearing race clip prior to
installing the slide-tray
assembly. Incorrect preparation
can cause damage to the slide-
rail assembly when installing
the slide tray.
4. Installing the slide tray
NOTE: The slide-tray assembly
is configured with a VGA video
cable. If the video source is
DisplayPort or DVI, replace the
VGA cable (with the provided
DisplayPort cable or a customer-
supplied DVI cable) before you
install the slide-tray assembly
into the slide rails in the rack.
Carefully route the cable
through the cable channel on
the CMA.
NOTE: Ensure the system is
properly supported until the
inner rails are inserted into the
outer slide rails on both sides .
With both the left and right
outer slide rails extended, and
the bearing races properly
seated, align and couple the
ends of the inner slide rails
(which are aixed to either side
of the slide tray) and outer slide
rails. The rails must be properly
nested before continuing. If
needed, decouple and
reposition the slide rail members
to achieve correct alignment.
Push the aligned slide tray into
the rack.
NOTE: Fully extend and retract
the slide tray at least once to
ensure all components are
properly seated.
5. Attaching the CMA
Slide the CMA latch over the
CMA attachment flange located
on the slide rail.
Secure the CMA latch to the
CMA attachment flange with
the thumbscrew.
Slide Tray Installation
Attaching the CMA
Slide rail
assembly
CMA latch with
thumbscrew
CMA
attachment
flange
Inner slide
rail
Outer slide
rail

To contact Vertiv Technical Support: visit www.VertivCo.com
© 2019 Vertiv Co. All rights reserved. Vertiv and the Vertiv logo are trademarks or registered trademarks of Vertiv Co. All other names and logos referred to are trade names,
trademarks or registered trademarks of their respective owners. While every precaution has been taken to ensure accuracy and completeness herein, Vertiv Co. assumes no
responsibility, and disclaims all liability, for damages resulting from use of this information or for any errors or omissions. Specifications are subject to change without notice.
KMMLED156 RACK MOUNT 15.6” CONSOLE TRAY FOR DELL EMC
Quick Installation Guide
4 590-2130-501A
NOTE: A Phillips head
screwdriver can be used to
tighten the thumbscrew in
tightly-spaced racks.
6. Connecting the console to
the target device
Connect the video and USB
connectors to the target device.
NOTE: Connect to one video
source at a time.
Connect the power cord to a
properly grounded electrical
outlet or power distribution unit
(PDU).
Secure the cables to the rear of
the slide rail with a wire tie.
Make sure the cables are not
pulled too tight.
(Optional) Bundle excess
cables into a figure-eight loop
and secure with a cable strap.
CAUTION: Do not coil the
cables. To minimize electrical
interference from the video
cable, arrange the cables in
figure-eight loops.
Video source configuration
The video source is factory set to
Auto, which automatically
configures for the connected
source. No other configuration is
required.
VGA shortcuts
If the RGB (VGA) video source is
connected, you can tap the Up icon
to automatically configure the
display and tap the Down icon to
automatically adjust the color.
Additional information
A translated version of this
information is available in the
Vertiv™ KMMLED156 Rack Mount
15.6” Console Tray for Dell EMC
Installer/User Guide located at
https://www.vertivco.com/en-us/
support/avocent-support-dell/.
Une version traduite de ces in-
formations est disponible dans
le guide d’installation et d’utilisa-
tion du plateau de console 15,6” à
montage en rack pour Dell EMC
KMMLED156 Vertiv™ situé à
l’adresse https://www.vertivco.
com/en-us/support/avocent-sup-
port-dell/.
Ein übersetztes Installations-/Be-
nutzerhandbuch für den Vertiv™
KMMLED156 18,5-Zoll-LCD-Kon-
solen-Tray für Dell EMC zur Bef-
estigung im Rack finden Sie unter
https://www.vertivco.com/en-us/
support/avocent-support-dell/.
Hay una versión traducida de esta
información en el Instalador/la
Guía del usuario de la Bandeja de
consola Rackmount de 15,6 pulg.
Vertiv™ KMMLED156 para Dell
EMC, disponible en https://www.
vertivco.com/es-latam/soporte/
avocent-support-dell/.
有关本信息的翻译版本，请参阅
《适用于 Dell EMC 的 Vertiv™
KMMLED156 机架式 15.6” 控制
台托盘安装人员/用户指南》，详见
https://www.vertivco.com/en-us/
support/avocent-support-dell/。
有關本資訊的翻譯版本，請參閱《適
用於 Dell EMC 的 Vertiv™
KMMLED156 機架式 15.6 主控台托
盤 安 裝 / 使 用 指 南 》， 詳 見 https://
www.vertivco.com/en-us/
support/avocent-support-dell/。
この情報の翻訳バージョンは、
「Vertiv™ KMMLED156 ラックマウント
15.6 インチ コンソールトレイ（Dell
EMC用）インストーラー/ユーザーガイ
ド」を 参照してくだ さい（https://www.
vertivco.com/en-us/support/
avocent-support-dell/）。
이 정보에 대한 번역본은 //www.
vertivco.com/en-us/support/avo-
cent-support-dell/에 있는 Vertiv™
KMMLED156 Rack Mount 15.6” Dell
EMC용 콘솔 트레이 설치자/사용자
설명서에 있습니다.
Перевод данной информации
доступен в руководстве по
установке консоли для монтажа
в стойку Verv™ KMMLED156
Rack Mount 15.6” для устройств
Dell EMC по ссылке: https://www.
vertivco.com/en-us/support/avo-
cent-support-dell/.
Versi terjemahan informasi ini
tersedia dalam Panduan Pengguna/
Installer Baki Konsol Rack Mount
15,6” KMMLED156 Vertiv™ untuk
Dell EMC yang ada di https://www.
vertivco.com/en-us/support/avo-
cent-support-dell/.
Securing the Cables to the Rear
of the Slide Rail
Wire tie cables
to slide rail