li'l pengyu Baby Bassinet BC318 User manual

BC318
Baby Bassinet

1
Baby Bassinet
Dear Li'l Pengyu customer,
Thank you for choosing our products!
All of our products are crafted with great attention to detail. We really appreciate
your trust and hope you'll be satisfied with your order. We are devoted to
answering your questions and listening to your feedback – please feel free to
contact us anytime at: [e-mail].
Your support means a lot to us! Li'l Pengyu will continuously strive to bring high-
quality products and serve our customers better.
Li'l Pengyu team

1
2
3
3
Side open button
Mesh
Folding button
Crib body(1pcs)
Wheels(4pcs)
Straps(2pcs)
WARNING:
The product is ready for use only when all locking parts are
engaged. Check carefully that these are engaged before use.
The mattress size is 31.49*19.69*0.79 in.
Only use the mattress sold with this crib. Do not add a second
mattress onto this one due to suffocation hazards.
Mattress, box springs & frame aligned .
ACCEPTABLE BED
FRAME IS IN-LINE
UNACCEPTABLE BED
MATTRESS, BOX SPRING &
FRAME ARE NOT IN-LINE
2
WARNING:
Ensure there is no gap between the
bedside sleeper and the adult’s bed.
Bassinet Height Guide: 20.8 In 22 In
23.2 In 24.4 In 25.6 In
To avoid the potential hazard of the baby’s neck being
caught on the top rail on the side that is next to the adult
bed, the top rail must not be higher than the adult bed
mattress.
To avoid the potential hazard of the baby being strangled,
the attachment system to the adult's bed shall always be
kept away from and outside of the crib.
After the bassinet is fixed firmly, the bottom support of the
adult bed should be flush against the bed frame.
Straps are for the
bedside sleeper mode.

IV. Operation
1
Adjust the Height Switch to bedside sleeper mode
1
2
5
1. Press the height adjustment
button on both sides of the bed, as
shown in the figure below.
2. Lift up the bassinet and adjust to
the desired height, as indicated by
the numbers on the side.
3. Release the height adjustment
button to lock the height level (a
“click” sound should be heard).
4. Make sure both sides are on the
same height.
II. Assembly
Step 1: Open the crib body
Expand the folding tubes
outwards on both sides until you
hear a “click” sound.
Step 2: Attach the bed board
Wrap the straps that extends from the two
sides of the bed board around the iron plates
on both foot tubes, and then buckle up under
the bed board (as shown). Pull straps to
tighten bed board.
Step 3: Install the wheels
Install the wheels onto the foot stands as
shown in the figure. There should be no
significant gap between the wheels and foot
stands.
4
III. Folding
1. Make sure to adjust the height to the
lowest position.
2. Lift the bed board.
3. Press folding buttons on both sides at the
same time.
4. Push both height adjustment tubes inward
(shown by the direction of the arrow).
1
2
3
3
1. Unbuckle the side buckles on both ends of the opening and zip
down.
2. Pressing the buttons under the bar, lift upwards to separate the
side frame.
3. Lock the wheels of the bassinet.
4. Adjust the height of the bassinet so that the bassinet mattress is
around the same height or slightly lower than the adult mattress.
5. Wrap the straps around the adult mattress and connect the
buckles to the bassinet.
6. Pull to tighten the straps and ensure that the bassinet is stable
against the edge of the adult bed.

7
6

Check screws, rivets, screws and other fasteners regularly to ensure
their firmness and safety, and replace any defective parts.
Check the crib locking device regularly.
Do not use the crib if any parts of the crib are damaged and contact
our customer support immediately.
Low viscosity oils or lubricants can be used as lubricants on moving
parts.
Do not use machine cleaning. Use a sponge, neutral detergent and
warm water for cleaning.
Maintenance
8