Librestream Onsight Cube User manual

ONSIGHT CUBE
USER GUIDE
LIBRESTREAM.COM

FOR MORE INFORMATION: CALL 1.800.849.5507 | +1.204.487.0612 LIBRESTREAM.COM 2
Librestream
Onsight Cube User Manual
Doc. #: 400335-06, rev. A
February 2020
Information in this document is subject to change without notice.
Reproduction in any manner whatsoever without the written
permission of Librestream is strictly forbidden.
Copyright Notice:
Copyright 2004-2019 Librestream Technologies Incorporated. All
Rights Reserved.
Patents Notice:
United States Patent # 7,221,386, together with additional
patents pending in Canada, the United States and other
countries, all of which are in the name of Librestream
Technologies Inc.
Trademark Notice:
Librestream, the Librestream logo, Onsight, the Onsight logo,
Onsight Connect, Onsight Flow, Onsight Workspace, Onsight
Cube, Onsight Hub, Onsight Smartcam, Onsight Platform
Manager and Onsight Teamlink are either registered trademarks
or trademarks of Librestream Technologies Incorporated in
Canada, the United States, European Union and/or other
countries. All other trademarks are the property of their
respective owners.

FOR MORE INFORMATION: CALL 1.800.849.5507 | +1.204.487.0612 LIBRESTREAM.COM 3
TABLE OF CONTENTS
INTRODUCTION ...........................................................
REQUIREMENTS FOR USEE...........................................
OPERATING AMBIENT TEMPERATURE ......................
HARDWARE FEATURES ..............................................
FRONT VIEW ................................................................................
TOP VIEW .....................................................................................
BACK VIEW ..................................................................................
BUTTON FUNCTIONS ..................................................
CHARGE THE ONSIGHT CUBE .....................................
CONNECTION STATUS ................................................
BATTERY LIFE .............................................................
TURN POWER ON ........................................................
TURN POWER OFF ......................................................
BLUETOOTH PAIR WITH AN ONSIGHT CUBE ..............
Wi-Fi PAIR WITH AN ONSIGHT CUBE ..........................
Wi-Fi DIRECT - Android ................................................................
DIRECT Wi-Fi - iOS ...........................................................................
Wi-Fi INFRASTRUTURE ..................................................................
CUBE SETTINGS AND CONTROLS ...............................
Check for Updates .......................................................................
Security ........................................................................................
Downloads ...................................................................................
Wi-Fi ..............................................................................................
Saved Cube ...................................................................................
CUBE AUDIO .................................................................
Cube Mic Audio ............................................................................
Bandwidth Control - Preferred Codecs ......................................
Viewer Window - Audio Control ..................................................
Client Policy - Audio Control ..........................................................
Cube Audio Troubleshooting .......................................................
CUBE IMAGES AND VIDEO .......................................... 9
CUBE CONTROL IN AN ONSIGHT CALL .......................
CUBE FILE MANAGEMENT ..........................................
TRANSFER FILES TO A WINDOWS PC .........................
THERMAL IMAGES .....................................................
TROUBLESHOOTING ...................................................
WINDOWS SUPPORT ..................................................
FOR MORE INFORMATION .........................................
FAQs ............................................................................
10
11
11
12
13
13
14
14
9
9
9
9
9
9
9
8
8
8
8
8
7
7
7
7
6
6
6
6
6
66
5
4
4
4
4
4
4
4

FOR MORE INFORMATION: CALL 1.800.849.5507 | +1.204.487.0612 LIBRESTREAM.COM 4
INTRODUCTION
The Onsight Cube is an industrial wearable accessory that works
with the Onsight Connect mobile application running on iOS and
Android devices.
Using the Onsight Cube and Onsight Connect, technicians can share
video and audio from the Cube for real-time collaboration with
remote experts.
The Onsight Cube features include:
• Camera: VGA, QVGA, D1, 720p and1080p 30fps
• Thermal Imager: VGA, QVA
• H.264/AVC
• USB: File transfer
• Integrated IEEE 802.11a/b/g/n (2.4/5.0 GHz)
• WiFi direct up to 200 meters
This manual describes the Onsight Cube and how to use it with
Onsight Connect for iOS/Android.
ONSIGHT CUBE USER MANUAL
REQUIREMENTS FOR USE
• Onsight Cube-R or Cube-EX
• Onsight 800 external battery charger
• Onsight Magnetic USB charging cable
• Onsight Connect application running on an iOS or
Android device
• Bluetooth and Location Services must be enabled on
the Onsight Connect host device to configure the Cube
If you have forgotten your Onsight Connect Password, press
‘Forgot Password’ at the login screen to receive an email with
a temporary Password. If you do not have an Onsight Connect
user account you may use Capture Mode. Contact your system
administrator to get an Onsight Connect user account.
Capture Mode provides ofine use of the Cube without requiring
an Onsight Connect login, Onsight calls are not supported in
Capture mode.
BACK VIEW
1. Charging Indicator
2. Connection Indicator
3. Camera Mode
4. Mount Connector
5. Power/USB Port
6. Speaker
FRONT VIEW
1. Camera
2. Laser
3. Buttons
4. Thermal Imager
5. Illumination
6. Microphone
7. Stream LED
8. Power Button
TOP VIEW
1. Camera Mode/
Recording
2. Image Capture/
Sharing
3. Illumination/Laser
HARDWARE FEATURES
OPERATING AMBIENT TEMPERATURE
The Cube operates within an ambient temperature range. If the
Cube is below the minimum operating temperature the voice
prompt will notify you it has entered Warming mode. The Cube
will vibrate every 5s and ash the yellow Charging Indicator until
the minimum operating temperature is reached. It will then
turn on. The Cube will power off automatically if the operating
temperature limit is exceeded.
Please refer to the Onsight Cube Technical Specs for Operating
Ambient Temperature guidelines.

FOR MORE INFORMATION: CALL 1.800.849.5507 | +1.204.487.0612 LIBRESTREAM.COM 5
The following table describes button functions based on the connection state of the Cube.
Standalone operation allows a user to operate the Cube when it is not paired with Onsight Connect on a host device.
Paired operation occurs when the Cube is paired with Onsight Connect on a host device.
BUTTON FUNCTIONS
BUTTON FUNCTIONS
CAMERA MODE/RECORDING
STANDALONE PAIRED
PRESS Start/Stop local recording PRESS Start/Stop local recording on host device
HOLD Toggle Video/Thermal/Fusion mode HOLD Toggle Video/Thermal/Fusion mode
IMAGE CAPTURE/SHARING
STANDALONE PAIRED
PRESS Capture Local Image PRESS Capture Image on Host Device
HOLD Capture and Share Image/Decline Call
ILLUMINATION/LASER
STANDALONE PAIRED
PRESS Toggle laser PRESS Toggle laser
HOLD Toggle Illumination HOLD Toggle Illumination
TAP ANY BUTTON TO ACCEPT AN INCOMING CALL
HOLD BOTH THE CAMERA MODE AND ILLUMINATION BUTTONS TO UNPAIR FROM THE HOST

FOR MORE INFORMATION: CALL 1.800.849.5507 | +1.204.487.0612 LIBRESTREAM.COM 6
Connect the power adapter to the Power Port and allow the battery
to fully charge. When the Cube is powered off, charging will take
approximately 4 hours. The battery will charge at a slower rate if the
Cube is powered on.
CHARGE THE ONSIGHT CUBE
You can operate the Onsight Cube while it is plugged
into the power adapter once it has reached a minimum
battery level of 10%.
While Battery is Charging
Green 100%
Orange less than 100%
On Battery Power
Green over 40%
Orange less than 40%
Red less than 20%
Red (flashing) less than 10%
Green Video mode
Red Thermal mode
Orange Fusion mode
Blue (flashing) Waiting to Bluetooth
pair to a host device.
Blue Cube is connected to its
wireless network but
is not paired to its host
device.
Green Cube is connected to
its host device and its
wireless network.
White (flashing) Firmware update in
progress, battery: 50%
or greater for update
required. Do Not Power
Off during the Update.
CHARGING INDICATOR:
CAMERA MODE INDICATOR:
CONNECTION STATUS INDICATOR:
CONNECTION STATUS
Bluetooth (BT) and Location Services must be enabled on
the Onsight Connect host device to configure the Cube.
To BT pair a Cube to an Onsight Connect host device:
• Power on the Cube.
• Log in to Onsight Connect on your host device.
• Hold your host device close to the front of the Cube to BT pair.
•You will hear a voice prompt ‘begin pairing’ and ‘host connected’
when complete.
• Press ‘Connect’ when the ‘Invitation to Connect’ appears.
•If Wi Direct connections are supported, the Cube receives
its network conguration from your paired host device
automatically. The connection status will be GREEN.
BLUETOOTH PAIR WITH AN ONSIGHT CUBE
Press the Power Button for one second to turn the Onsight Cube
ON.
TURN POWER ON
Press the Power Button for one second to turn the Onsight Cube
OFF. The Cube automatically powers off after 5 minutes of inactivity.
TURN POWER OFF
Media Configuration Run Time
(Hrs)
QVGA, 10fps, 1Mbps, Laser On 4.5
VGA, 10fps, 1Mbps, Laser On 4.5
1080p, 10fps, 1.5Mbps, Illumination On,
Laser On
3
D1, 10fps, 1Mbps, Illumination On, Laser On 3.5
1080p, 10fps, 1.5Mbps, Illumation On, Laser
On,
2.75
Standalone recording: 1080p, 30fps, 6Mbps,
Laser On
2.25
Fusion, 720p, 30fps, No Illumination, No
Laser
3.5
BATTERY LIFE
Battery life can vary depending on the selected media conguration,
use the table below as a guideline.
*Battery Life can be extended by turning the Laser and Illumination
off.

FOR MORE INFORMATION: CALL 1.800.849.5507 | +1.204.487.0612 LIBRESTREAM.COM 7
The wireless network conguration for the Cube is completed
over the initial Bluetooth connection. Once the wireless
conguration is complete, the Cube and host device are WiFi
paired. All Onsight data communication between the Cube and
host device is over the wireless network.
The options for the Cube’s wireless connection includes:
• WiFi-Direct
• Wireless Infrastructure
Wi-Fi DIRECT - Android
Wi Direct is a Peer to Peer connection between the Cube and
your Android host device. When using Android devices, this is
the preferred method for most situations, e.g., the Cube is used
as a wearable device. (Note: the Cube does not support WiFi
Direct with iOS at this time, see WiFi Infrastructure.)
•The Cube automatically receives its Wi Direct
conguration from your BT paired host device.
• Press ‘Connect’ when the ‘Invitation to Connect’ appears.
The connection status will be GREEN.
• You will hear a voice prompt ‘WiFi connected’.
•Once Wi paired, the Cube is automatically selected as the
video source.
• The Cube will automatically WiFi pair with that host device
the next time you log in to Onsight Connect.
Wi-Fi PAIR WITH AN ONSIGHT CUBE
DIRECT Wi-Fi - iOS
Direct Wi-Fi is a Peer to Peer connection between the Cube and
your iOS host device. When using iOS devices, this is the preferred
method for most situations, e.g., the Cube is used as a wearable
device. However, when the Cube is connected to Direct Wi-Fi
with an iOS device, the iOS device must use a cellular connection
in order to place Onsight Calls. The iOS device’s Wi-Fi network
connects directly to the Cube and is not available for use as an
internet connection.
•The Cube automatically receives its Direct Wi-Fi conguration
from your BT paired iOS host device.
• Press ‘Connect’ when the ‘Invitation to Connect’ appears. The
connection status will be GREEN.
• You will hear a voice prompt ‘Wi-Fi connected’.
•Once Wi paired, the Cube is automatically selected as the
video source.
• The Cube will automatically Wi-Fi pair with that host device the
next time you log in to Onsight Connect.
Wireless Connection Type Supported devices
Wifi Direct
(Automatic configuration)
Android
iOS
Wifi Infrastructure
(Manual Configuration)
Android
iOS
See Wi-Fi PAIR WITH AN ONSIGHT CUBE for details on manually
conguring the wireless connection.
• You will hear a voice prompt ‘Wi-Fi connected’.
• Once Wi-Fi paired, the Cube is automatically selected as the
video source.
• The Cube will automatically Wi-Fi pair with that host device the
next time you log in to Onsight Connect.
Wi-Fi INFRASTRUCTURE
Wi-Fi Infrastructure is a manually congured wireless connection
between the Cube and your network infrastructure, e.g., Access
Point or Hot Spot.
The Cube must be connected to the same network as your host
device.
• Once BlueTooth pairing has completed, select Wi-Fi-Status.
• Select the network you want the Cube to connect
with from the Available Networks list. This must
be the same network to which your host device is
connected.
• Enter the password for the network and press
Join.
• You will hear a voice prompt ‘Wi-Fi connected’.
• Once paired, the Cube is automatically selected as the video
source.
• The Cube will automatically Wi-Fi pair with that host device
the next time you log in to Onsight Connect. The Cube and host
device must be on the same network.
The Cube will remain Wi-Fi paired to the Host as long as they are on
the same network with each other. They will automatically Wi-Fi pair
to each other whenever they are on the same network.
If the Cube is not currenlty Wi-Fi paired to a host, it is available to
BT pair with another host device running Onsight Connect. The
Cube may be BT paired to multiple host devices, but a host device
may only be BT/Wi-Fi paired to a single Cube. Use Settings-Forget
Pairing to unpair with a Cube.

FOR MORE INFORMATION: CALL 1.800.849.5507 | +1.204.487.0612 LIBRESTREAM.COM 8
Settings
Cube Settings are controlled using the Onsight Connect
software on a paired host device.
Using Onsight Connect on the host device, select the
SETTINGS button on the Dashboard:
• Tap Cube
• View details such as pairing state, name, version,
battery level, and voice prompt settings
•Wi: Status, IP address, and MAC address
• Save Pairing: Name and Forget Pairing
The Cube is congured using the Onsight Connect application while
paired with a host device.
CUBE SETTINGS AND CONTROLS
Details include:
• Name
• Firmware Version
• Battery
• Power Off Timeout
• Voice Prompts and Volume
• Check for Updates
Details
Voice Prompts are enabled by default. They are used to indicate
the current status of the Cube.
• Go to Settings - Cube.
• Select the Voice Prompt you wish to use: UK or US, Female
or Male. Set to None to disable Voice Prompts.
• Set the Voice Prompt Volume slider to control the Cube’s
volume.
Voice Prompts
To download the latest rmware update for the Cube press the
‘Check for Updates...’ button..
• Press ‘Check for Updates...’
• Follow the onscreen instructions.
WARNING: DO NOT POWER OFF THE CUBE DURING A FIRMWARE
UPDATE. ONCE THE UPDATE HAS COMPLETED THE CUBE WILL
REBOOT AUTOMATICALLY.
Check for Updates
Downloads
Files that have been captured in Standalone mode (i.e. when not
paired with a host device) can be downloaded from the Cube to the
Connect app. This includes still image jpegs and video recordings.
• Go to Files-Cube.
• Select a Folder or Files.
• Select Download from the menu.
The les will be saved to the My Files tab and can be identied by
the Cube icon displayed on their thumbnail image. If multiple les
are downloading you can check their status by clicking on the Cube
status icon.
To transfer les directly from the Cube to a PC using an USB cable
you must rst login to Onsight Connect and pair with a Cube.
Use the File Explorer to access the Onsight Connect les. Select
Cube-Intenal Storage- DCIM - Call Folder.
For iOS, use iTunes to access File Sharing under the Onisght
Connect in the Apps list. Save the Calls folder to the PC.
For Android, use the File Explorer to access Cube les.
Wi-Fi
•Congure Wi-Fi
•Choose and congure the Cube’s Wi-Fi network. This
should be the same network to wihich this device is con-
nected.
• Wi-Fi Direct (Android)
• Direct Wi-Fi (iOS)
•Frequency
• IP Address
• MAC Address
Install Certicates
You may install certicates on the Cube if they are required for Wi-
Fi conguration.
•Use File Sharing in iTunes to install certicates to iOS
host devices. This will make them available for use on the
Cube.
•For Android, copy the certicates to the host device’s
storage. Pressing the Install Certicates button will give
instructions on where the certicates need to be stored on
the host device.
Remove All Certicates:
•This will delete all certicates that have been installed on
the Cube.
Security
Set the period of inactivity that the Cube will wait before powering
off.
• Default: 10 minutes
• Options: 5 - 30 minutes, Never.
Power Off Timeout

FOR MORE INFORMATION: CALL 1.800.849.5507 | +1.204.487.0612 LIBRESTREAM.COM 9
Includes:
• Name
• Forget Cube - Select to forget the pairing with a Cube
Saved Cube
System Health
The color of the System Health button provides a visual indication
of the system readiness. If the button is green, all the underlying
services are available. If the button is red, one or more of the
services is not available and could cause an issue. Select Details to
view the Cube Details:
• Cube status
• Battery Level
• Firmware version
Reset
Includes:
• Reset Network - press to clear all network settings
•Factory Reset - press to clear the Cube of all conguration
and data les
Tip: To perform a factory reset using the buttons on the Cube, turn
off the Cube. Hold down the Illumination and Camera mode buttons
then press the On button.
Cube Mic Audio
The Cube’s microphone is only active when:
1. The Cube is paired to a host device and is the video source.
2. The Cube is recording video in stand alone mode.
To make sure the Cube’s Mic is enabled and capturing sound,
conrm the following Settings are enabled in the Connect app.
Bandwidth Control - Preferred Codecs
Cube Audio is active only when Subject Audio is enabled by the
Onsight Connect App. Set the Bandwidth Control - Preferred Codecs
as follows to enable Cube Audio.
• Subject Audio: Default (G.711) or Low Bit Rate (GSM).
CUBE AUDIO
This section describes how to congure and control Cube Audio
while in an Onsight Call. The Cube’s Mic is the sound source for the
video audio track. Your host device’s microphone is the sound source
for the voice audio track.
Viewer Window - Audio Control
Cube Audio can only be heard when Subject Audio is enabled
by the Onsight Connect App. When streaming Cube Video or
playing back a Cube recording, you can control the playback
Audio in the Viewer Window. Use Playback Audio to mute/
unmute the Cube Audio.
• Playback Audio - when streaming video or watching
a recording, this option will mute/unmute the audio
coming from the video stream or recording. You will
still hear the main Conversation Audio.
Client Policy - Audio Control
Your OPM Administrator may control your Subject Audio
settings by using a Client Policy. The Client Policy is applied
whenever you are logged in to your Onsight client app.
Cube Audio Troubleshooting
If your call participants are unable to hear Cube Audio when in
a call check your Settings to conrm Subject Audio is enabled.
If not, enable Subject Audio. You may need to contact your
OPM Admin to get permissions to edit the settings.
If you are receiving video from a Cube user in a call and cannot
hear Cube Audio conrm Playback Audio is not muted in the
Viewer window’s Audio settings.
CUBE IMAGES AND VIDEO
When paired with a host device, the Cube supports specic
resolutions depending on the video mode: Optical or Thermal.
If a media conguration is chosen that does not include a
resolution supported by the Cube then the closest resoution
supported by the Cube will be used.
Paired mode Resolution
Images Image Capture Setting*
Optical QVGA, VGA, D1, 720p,
1080p
Thermal (Fusion) QVGA, VGA
Standalone mode Resolution
Images 13 MP (4208x3120)
Video (Optical) 1080p 30fps
Video (Thermal/Fusion) VGA
*Image Capture Resolution can be set to L, M, H or Max. This
will depend on the supported resolutions of the host device.

FOR MORE INFORMATION: CALL 1.800.849.5507 | +1.204.487.0612 LIBRESTREAM.COM 10
Selecting the Cube as the Video Source
Press the Video Source button to change between Cube, Cube
Thermal and Cube Fusion as the video source.
• Cube: Video - VGA, QVGA, D1, 720p and1080p 30fps
• Thermal: Thermal imager - VGA, QVGA
• Fusion: Thermal imager including object edge detection
CUBE CONTROL IN AN ONSIGHT CALL
This section describes how to control the Cube while in an Onsight
Call.
CUBE FUNCTIONS
Press the Cube button on the control bar to access
the Cube functions.
Spot Temperature
When in Thermal or Fusion modes, tap
and hold the Viewnder to place the spot
temperature indicator on a location.
Fusion
Fusion enhances Thermal images by applying edge detection
to objects. For the best edge detection alignment of the thermal
image, objects of interest should be the the point of focus. Tap the
Viewnder to focus on the object.
The focus region will be shown on the Viewnder while the camera
is focusing.
Use the slider to manually align the edge with the thermal image
when focusing on the object of interest is difcult.
Note that closer objects, 20 cm or less, may cause the upper portion
of the eld of view to appear misaligned. Keep the object of interest
in the center of the screen for the best alignment. Use the slider to
make manual adjustments.
Zoom
Press the Zoom button to adjust between 1X and 3X Optical Zoom.
Note: Optical Zoom is not supported when using Thermal or Fusion
modes. You may use pinch gestures to digitally scale and pan the
Thermal image.
TIP: To align close objects with edge detection, tap and hold the
Viewnder to place the spot temperature indicator on the object of
interest.
Temperature
To select the Temperature display when in Thermal or Fusion
modes, tap the Spot Temperature button to toggle between Celcius
or Fahrenheit.
Focus
The Cube will auto focus on the center of the Viewnder when the
Cube is the video source. Objects can not be closer than 10 cm ( or
4 inches).
In Fusion mode with Spot Temperature enabled, the Cube will focus
on the location of the Spot Temperature placement.
Image Capture
When the Cube is the video source, image capture is dependent on
its selected video mode. The optical camera will capture images up
to a maximum resolution of 13MP. The thermal imager will capture
images up to VGA.
Laser
To enable the Laser pointer press the Laser button.
Emissivity
This setting adjusts the thermal imager’s temperature reading
based on an object’s ability to emit heat (thermal energy). Select the
setting which best describes the object’s surface:
•Matte (dull, at, not shiny)
• Semi-Matte (dull with a slight shine)
• Semi-Gloss (more shine than Semi-Matte)
• Gloss (shiny)
TIP: When the Cube is disconnected from a host device, the Onsight
Connect application will automatically switch back to the host’s
internal camera as the video source.
Selecting the Cube as the Video Source
Press the Video Source button to change between Cube, Cube
Thermal and Cube Fusion as the video source.
• Cube: Video - VGA, QVGA, D1, 720p and1080p 30fps
• Thermal: Thermal imager - VGA, QVGA
• Fusion: Thermal imager including object edge detection
Thermal
Thermal mode enables the Cube’s thermal imager producing
images based on object temperature differences. See the Thermal
Images section for details. .

FOR MORE INFORMATION: CALL 1.800.849.5507 | +1.204.487.0612 LIBRESTREAM.COM 11
To manage Cube les directly from a PC:
• Power on the Cube.
• Pair to the Cube with your mobile device running the Onsight
Connect application.
• Attach the USB/Charging cable to the Cube adn connect the
cable to your Windows PC’s USB port.
• Open File Explorer on your Windows PC.
• Navigate to the Cube/Internal Storage/DCIM folder to copy
les to folder on your Windows PC.
TRANSFER FILES TO A WINDOWS PC
CUBE FILE MANAGEMENT
This section describes le management on the Cube.
Image Capture and Recording while Paired to a Cube
While paired to a Cube any captured images or video recordings
are stored locally on the host device. They will be saved in the My
Files section of the Files tab, They are not saved in the Cube’s
local storage.
Any images and recordings saved while paired to a Cube are
stored locally on the host device (iOS or Android).
When operating the Cube in Stand-alone mode (i.e. not paired to
a mobile devcie) all images and recordings are stored locally in
the Cube’s internal storage. They can be accessed by pairing with
the Cube and going to FILES-Cube.
You may download les from the Cube to your host device by
selecting the thumbnail image of the les and pressing Download
on the menu. Cube les may be downloaded or deleted from the
Cube.
When downloading les from the Cube you will see the Download
Status screen. Press Files to return to the Cube tab.
Once the les have been successfully downloaded from the
Cube they will be placed in the My Files tab in a date stamped
folder. All les downloaded from the Cube will have a Cube icon
displayed on their thumbnail image.

FOR MORE INFORMATION: CALL 1.800.849.5507 | +1.204.487.0612 LIBRESTREAM.COM 12
THERMAL IMAGES
The Thermal and Fusion modes use the built-in Thermal Imager
to capture Thermal Video and Still Images. The Thermal Imager
captures the heat being radiated from an object’s surface and
approximates the temperature to create a picture of the heat
signature coming off of its surface.
So how does a thermal imager capture the temperature of objects
accurately? The answer is by knowing the objects ability to emit heat
also known as its Emissivity. By setting the Emissivity value, you are
telling it how to interpret the heat coming off of an object.
Emissivity
Emissivity is the measure of how efciently a surface emits heat
(thermal energy). In order to accurately approximate an object’s
temperature, the Cube’s themal imager must know the emissivity of
the object. Emissivity is expressed as a value between 0 and 1.0. The
higher an object’s Emissivity, the more heat it gives off.
Different objects emit heat differently from their surfaces. Two
objects that are the same temperature can look like they are
different temperatures in a Thermal Image because they emit heat
at different rates. For example, if you take a picture of a BBQ, the
black painted surfaces will appear hotter than the shiny metal
portion of the BBQ even though they are the same temperature.
Shiny metal does not emit heat as readily as a at black painted
surface.
So if you’ve set Emissivity to Gloss, the spot temperature tool will
accurately report the temperature for the shiny metal part of the
BBQ but will not report accurately for the black painted surfaces.
By setting Emissivity to a specic value, you are telling the thermal
imager what type of object you are observing and therefore how to
interpret the temperature.
The Emissivity setting adjusts the thermal imager’s temperature
reading based on an object’s ability to emit heat (thermal energy).
For the most accurate temperature readings, select the setting
which best describes the object’s surface:
• Matte (≥0.90)
• Semi-Matte (0.70 - 0.90)
• Semi-Gloss (0.45 - 0.70)
• Gloss (0 - 0.45).
The selected Emissivity will also adjust the Temperature range
displayed on the Viewer.
When using Thermal or Fusion modes, select the Emissivity value
that best describes the surface of the object.
Note that comparing objects with different Emissivity values will
not yield accurrate temperatures unless you adjust the Emissivity
setting for each object before using the Spot Temperature tool.
Object Emissivity Setting
concrete
wood
rubber
tile (ceramic)
iron (rusted)
water (liquid)
soil
paint
plastic
Matte
Steel (Oxidized)
Black Enamel Paint
Semi-Matte
Stainless Steel
Styrofoam
Semi-Gloss
Steel (Galvanized)
Steel (Mild)
Zinc (Galvanized)
Aluminum
Gloss
Emissivity Settings
Use the table below to best approximate the
Emissivity of objects.
Fusion mode
Fusion combines the outline of objects with their thermal image.
The alignment is automatic but depending on the distance to the
object it may need to be manually adjusted using the slider.
Use the slider to adjust the outline of objects with their thermal
image.
To return to automatic alignment tap the X to the right of the slider.

FOR MORE INFORMATION: CALL 1.800.849.5507 | +1.204.487.0612 LIBRESTREAM.COM
13
Pairing with the Cube
Your host device must have Bluetooth enabled in order to pair with a
Cube. You must have either Android v5.1 or higher, or have iOS v10
or higher installed.
Symptoms
When Onsight Connect is not pairing with the Cube, one or all of the
following is occurring:
• System Health: Cube is not connected.
• Settings-Cube: Pairing state is not connected.
• Cube’s Connection Indicator is NOT SOLID GREEN.
Solutions
• Update your OS. Your host device may not be running the
minimum required Android or iOS version in order to connect to
the Cube.
• Move the Cube closer to your smartphone. The Cube and
host device may not be close enough to establish a Bluetooth
connection.
•Congure the Wi-Fi network. If the Cube can not establish a
WiFi-Direct connection with the host device, go to Settings-
Cube-WiFi and tap on Status to select a Wi-Infrastructure
access point to connect.
•Bluetooth must be enabled to congure the Cube.
• For iOS, use the Control Center to turn on Blue-
tooth.
• You may also need to tap the System Settings
button to go to Settings to enable Bluetooth and
Allow New Connections.
TROUBLESHOOTING Cube Video not Visible
Symptoms
Onsight Connect is paired with the Cube but the video from the Cube
is not visible in the viewnder.
Possible Causes
• The host device is paired with the Cube but has not completed
its connection to the Cube over the Wi network. Wait a few
moments for the Wi-Fi connection to establish.
•The Cube has not established a Wi-Direct connection with the
host device. Go to Settings-Cube-Wi-Fi and tap on Congure Wi-
Fi to select an Available Network. Enter the password to join the
network.
• The Cube has not been selected as the video source in the
viewnder. Press the Video Source button to select Cube, Cube
Thermal or Fusion.
If Still Unable to Pair with the Cube...
Hold down both the Video and Illumnation buttons at the same time
to forget the Cube pairing and retry. You may also go to Settings-
Cube-Forget Cube to reset the pairing.
WINDOWS SUPPORT
•The Cube supports pairing with a Windows PC/Tablet. Onsight
Connect Users can access all Cube related UI features which
include:
oSystem Health status
oCube Settings
oCube Icon in the status bar
oCube controls for laser and thermal settings
oCube video selection: Cube, Thermal, Fusion
oSelection of Spot Temperature for thermal and fusion
•Cube pairing for Onsight Connect for Windows clients using
BluetoothLE
•Cube connection using Direct WiFi
•Transfer files to/from a connected Cube

FOR MORE INFORMATION: CALL 1.800.849.5507 | +1.204.487.0612 LIBRESTREAM.COM 14
FOR MORE INFORMATION
Please contact [email protected] or call 1.800.849.5507 or
+1.204.487.0612.
FAQs
How do I Pair with the Cube?
Login to Onsight Connect and turn on the Cube. When the Cube’s
voice prompt says ‘System Ready’, hold the cube within close
proximity to the host device. This will initiate the pairing process.
Bluetooth and Location Services must be enable on your host device,
if any services are turned off you will be prompted to enable them.
How do I stream video from the Cube?
Login to Onsight Connect and turn on the Cube. When the Cube is
paired with a host device, it automatically becomes the video source.
Place an Onsight Call to stream video to a remote team member.
How do I factory reset the Cube?
When the Cube is powered off, hold both the Video and Illumination
buttons down then press the Power button. The Cube will reset and
delete all files in local storage.