LifeSpan Kids ROCKA PE18 User manual

1
PE18
ROCKA WOODEN SEESAW
OWNER'S MANUAL
IMPORTANT:
This product may contain sharp points and small parts prior to assembly.
The owner’s manual contains safety, assembly, use and maintenance instructions. This product must be assembled by an adult
who has read and understood these instructions. Keep the packaging away from children and dispose of all packaging before use.
For the installer and your children’s safety, it is important to fully read and understand the instructions and safety hazards before
commencing the assembly of the product.
WARNING!
The disassembled product
may contain small parts
which pose a choking hazard
to children under 3.

2
TABLE OF CONTENTS
1. GENERAL SAFETY 3
1.1 DANGER FOR CHILDREN 3
1.2 RISK OF INJURIES 3
1.3 PRODUCT DAMAGE 4
1.4 ASSEMBLY ADVICE 4
2. SAFETY INSTRUCTIONS 5
3. ASSEMBLY INSTRUCTIONS 7
4. MAINTENANCE 12
5. CLEANING 14
6. WARRANTY 14

3
1 GENERAL SAFETY
This product is intended for outdoor domestic use only.
Maximum user weight per seat: 50kg
1.1 DANGER FOR CHILDREN
WARNING! No eating while using the product
•Children do not recognize potential dangers from this product. The product must be stored out
of reach of children and pets.
•This product may only be used with adult supervision at all times.
•The packaging material is not suitable for children due to choking and suffocation hazards.
1.2 RISK OF INJURIES
•Do not use the product if it is damaged or defective. If it is damaged or defective, please
contact a qualified technician.
•Check the product before each use. Defective parts must be changed immediately as they
can impair the function and the safety of the product.
•No more than one person to use the product at the same time.
•Use the product only on even and non-slipping surfaces. Never use it near water and keep
sufficient space around for safety.
•Beware of moving parts such as the springs or elastics, which could catch your arms and legs.
Do not place any objects or body parts in the product’s openings.
1.3 PRODUCT DAMAGE
•Do not make alterations to the product. Only use original spare parts. Qualified technicians
should only carry out repairs – improper repairs can lead to danger for the user. Use this
product only as described in this manual.
1.4 ASSEMBLY ADVICE
•The assembly of the product must be done carefully and by an able-bodied adult. If in any
doubt, ask a technically qualified person.
•Before you start with the assembly, read the instructions carefully.
•Remove all packaging materials and lay down all parts on an open space. This gives you an
overview and simplifies the assembly procedure.
•Check with the parts list that all parts are available. Dispose of the packaging material when
the assembly is completed.
•Beware that when using tools or doing technical work, there is always a risk of injuries.
Assemble the product with care.

4
•Create a danger free environment; for example, do not let tools lay around the workspace.
Store the packaging material in a way that cannot cause any danger.
•After installing the product according to the instruction manual, en sure all screws, bolts and
nuts are correctly installed and tightened and that all joints are secure.
•Reasonable space must be kept between the product and possible sources of danger, such
as other equipment swimming pools and fences.
•The product must be assembled correctly before use.
•Your play structure must be installed on a flat horizontal surface with a minimum of 2m
between it and any structure or obstacle such as a fence, garage house, tree branches, cloths
lines, or electric cables.
•Modifications made to the original product shall be carried out according to the instructions of
the manufacturer.
•The product must always be used in a well-lit area.
•Do not place anything under the product.
•Use gloves during assembly and disassembly.
•Outdoor products should be equipped with a device that in strong wind conditions avoid
displacement due to wind (e.g. steel bars in the ground or loads like sand bag or water bags).
•In certain areas during winter, snow buildup and the low temperatures can damage the
product. It is recommended to remove snow buildup and to store the product indoor.
•We strongly recommend visual inspections every 3 months to insure the integrity of the entire
product. Replace any parts as necessary.

5
2 SAFETY INSTRUCTIONS
•The safety instructions of the product should always be considered and obeyed.
•Using the product may result in permanent injury such as paralysis, or even death. Falling off
the product may lead to injuries, particularly to the back, neck or head.
•No clothes with hooks or lose parts should be worn or carried during product usage in order to
avoid hooks getting caught and causing injury.
•Strong winds can result in the product being blown away or damaged. If strong winds are
predicted the product must be disassembled and moved to a sheltered area or sufficiently
anchored down.
•Moving the product whilst assembled may affect the integrity of the frame. Should it be
necessary to move the product, please consider the following:
1.) Force to be evenly spaced around the frame to lift the product off the ground
2.) The product must be carried horizontally
3.) Use caution whilst moving as it could bend the product frame.
•Users should be familiar with the assembly manual. This manual contains assembly guidance;
selected precautionary measures as well as recommendations for servicing and maintenance
of the product, in order to ensure a secured and fun use of the product.
•It is the responsibility of the owner or the supervisor to guarantee that all users of the product
are informed sufficiently of all warning references and safety instructions.
For the supervisor:
The supervisor’s role is to make sure users are aware of all safety precautions and that these
precautions are enforced. When a supervisor is not available, the product may be disassembled or
covered to limit access.
•The product can be only used if it is in good condition, worn or damaged parts should be
replaced.
•Objects, which could be dangerous to the user, should be away from the product
•Avoid unauthorized and unsupervised use of the product.
•Do not use the product under influence of alcohol or drugs (incl. medicines).
•Do not use the product as a jumping platform for other articles.

6
Consumer Information Sheet for Playground Surfacing Materials
The US Consumer Product Safety Commission (CPSC) estimates that about 100 000 playground
equipment-related injuries resulting from falls to the ground surface are treated annually in US
hospital emergency rooms. Injuries involving this hazard pattern tend to be among the most serious
of all playground injuries, and have the potential to be fatal, particularly when the injury is to the head.
The surface under and around playground equipment can be a major factor in determining the injury-
causing potential of a fall. It is self-evident that a fall on to a shock-absorbing surface is less likely to
cause a serious injury than a fall onto a hard surface. Playground equipment should never be placed
on hard surfaces, such as concrete or asphalt, and while grass may appear to be acceptable, it may
quickly turn to hard-packed earth in areas of high traffic. Shredded bark mulch, wood chips, tine sand
or the gravel are considered to be acceptable shock absorbing surfaces when installed and
maintained at a sufficient depth under and around playground equipment.
Table B.1 lists the maximum height from which a child would not be expected to sustain a life-
threatening head injury in a fall on to four different loose-fill surfacing materials if they are Installed
and maintained at depths of 150 mm, 225 mm and 300 mm.
Table B.1: Fall height in millimetres from which a life-threatening head injury would not be
expected
However, it should be recognised that all injuries due to falls cannot be prevented, no matter what
surfacing material is used.
It is recommended that a shock absorbing material extend a minimum of 1 800 mm in all directions
from the perimeter of stationary equipment such as climbing frames and slides. However, because
children may deliberately jump from a moving swing, the shock absorbing material should extend in
the front and rear of a swing a minimum distance of twice the height of the pivot point measured from
a point directly beneath the pivot on the supporting structure.
This information is intended to assist in comparing the relative shock-absorbing properties of various
materials. No particular material is recommended over another. However, each material is only
effective when properly maintained. Materials should be checked periodically and replenished to
maintain correct depth as determined necessary for the equipment in question. The choice of a
material depends on the type and height of the playground equipment, the availability of the material
in a particular area, and its cost.
Type of Material Depth of surfacing material
150mm
225mm
300mm
Double Shredded Bark Mulch
1800
3000
3300
Wood Chips
1800
2100
3600
Fine Sand
1500
1500
2700
Fine Gravel
1800
2100
3000

7
3 ASSEMBLY INSTRUCTIONS
SS01 X 4PCS SS02 X 1PC SS03 X 1PC
SS07 X 1PC SS08X 2PCS Anchor x 4 PCS
SS04 X 2PC SS05X 1PC SS06 X 4PCS
M10X95MM 1PC M8X105MM 4PCS M8X95MM 1PC M8X86MM 4PCS
M4X25MM 22PCS Spanner 1PC Allen Key 1PC M10 Nut 1PC M8 Nut 9PCS Washer 2PC
√

8
Step 1: 12pcs of M4 x 25mm
SS06 X 4PCS
SS01 X 4PCS
SS02 X 1PC
Step 2: 2pcs of M4 x 25mm
SS03 X 1PC

9
Step 3:
4pcs of M4 x 25mm
1pc of Bolt M8 x 95mm
Step 4:
4pcs of M4 x 25mm
4pcs of M8 x 86mm
SS07 X 1PC
SS04 X 2PCS
SS05 X 1PC

10
Step 5:
1pc of Bolt M10 x 95mm
2pcs of Plastic washer
Step 6:
4pcs of Bolt M10 x 105mm
SS08 X 2PCS