LifeSpan Kids LK41 User manual

1
LK41 3M MONKEY BARS
BARS ONLY*
OWNER'S MANUAL
IMPORTANT:
This product may contain sharp points and small parts prior to assembly.
The owner’s manual contains safety, assembly, use and maintenance instructions. This product must be assembled by an adult
who has read and understood these instructions. Keep the packaging away from children and dispose of all packaging before use.
For the installer and your children’s safety, it is important to fully read and understand the instructions and safety hazards before
commencing the assembly of the product.
WARNING!
The disassembled product
may contain small parts
which pose a choking hazard
to children under 3.
*NOT INCLUDING TIMBERS

2
TABLE OF CONTENTS
1. GENERAL SAFETY INSTRUCTIONS 3
1.1 DANGER FOR CHILDREN 3
1.2 RISK OF INJURIES 3
1.3 PRODUCT DAMAGE 3
1.4 ASSEMBLY ADVICE 4
2. SAFETY INSTRUCTIONS 7
3. ASSEMBLY INSTRUCTIONS 8
4. MAINTENANCE 10
5. CLEANING 11
6. WARRANTY 11

3
1 GENERAL SAFETY
This product is intended for indoor and outdoor, domestic use only.
Weight Limit: 50kg per bar
Maximum Fall Height: 1995mm
1.1 DANGER FOR CHILDREN
•WARNING! No eating while using the product
•Children do not recognize potential dangers from this product. The product must be stored out of
reach of children and pets.
•This product may only be used with adult supervision at all times.
•The packaging material is not suitable for children due to choking and suffocation hazards.
1.2 RISK OF INJURIES
•Do not use the product if it is damaged or defective. If it is damaged or defective, please contact a
qualified technician.
•Check the product before each use. Defective parts must be changed immediately as they can
impair the function and the safety of the product.
•No more than one person to use the product at the same time.
•Use the product only on even and non-slipping surfaces. Never use it near water and keep sufficient
space around for safety.
•Beware of moving parts such as the springs or elastics, which could catch your arms and legs. Do
not place any objects or body parts in the product’s openings.
1.3 PRODUCT DAMAGE
•Do not make alterations to the product. Only use original spare parts. Qualified technicians should
only carry out repairs –improper repairs can lead to danger for the user. Use this product only as
described in this manual.
•Protect the product against splashes, humidity, high temperature and direct sunlight.

4
1.4 ASSEMBLY ADVICE
•The assembly of the product must be done carefully and by an able-bodied adult. If in any doubt,
ask a technically qualified person.
•Before you start with the assembly, read the instructions carefully.
•Remove all packaging materials and lay down all parts on an open space. This gives you an
overview and simplifies the assembly procedure.
•Check with the parts list that all parts are available. Dispose of the packaging material when the
assembly is completed.
•Beware that when using tools or doing technical work, there is always a risk of injuries. Assemble
the product with care.
•Create a danger free environment; for example, do not let tools lay around the workspace. Store the
packaging material in a way that cannot cause any danger.
•After installing the product according to the instruction manual, en sure all screws, bolts and nuts
are correctly installed and tightened and that all joints are secure.
•Reasonable space must be kept between the product and possible sources of danger, such as
other equipment swimming pools and fences.
•The product must be assembled correctly before use.
•Place the product on a level surface at least 2 m from any structure or obstruction such as a fence,
garage or house.
•Modifications made to the original product shall be carried out according to the instructions of the
manufacturer.
•The product must always be used in a well-lit area.
•Do not place anything under the product.
•Use gloves during assembly and disassembly.
•Outdoor products should be equipped with a device that in strong wind conditions avoid
displacement due to wind (e.g. steel bars in the ground or loads like sand bag or water bags).
•In certain areas during winter, snow buildup and the low temperatures can damage the product. It is
recommended to remove snow buildup and to store the product indoor.

5
•We strongly recommend visual inspections every 3 months to insure the integrity of the entire
product. Replace any parts as necessary.
ANCHORING
Note: the unit can be anchored directly into the ground using the anchors provided.
You may also use cement for additional stability, please follow the below instructions.
d
e
- Install the provided anchors (e) by screwing them in at positions (d)
- Dig a 350mm3 hole in the ground positioned under the feet of the
unit that you wish to concrete anchor.
- Fill hole with cement and insert leg with anchor attached into cement
- A minimum of 5 cm depth below ground level of concrete anchoring is
needed.

6

7
2 SAFETY INSTRUCTIONS
•The safety instructions of the product should always be considered and obeyed.
•Using the product may result in permanent injury such as paralysis, or even death. Falling off the
product may lead to injuries, particularly to the back, neck or head.
•No clothes with hooks or lose parts should be worn or carried during product usage in order to avoid
hooks getting caught and causing injury.
•Strong winds can result in the product being blown away or damaged. If strong winds are predicted
the product must be disassembled and moved to a sheltered area or sufficiently anchored down.
•Moving the product whilst assembled may affect the integrity of the frame. Should it be necessary to
move the product, please consider the following:
1.) Force to be evenly spaced around the frame to lift the product off the ground
2.) The product must be carried horizontally
3.) Use caution whilst moving as it could bend the product frame.
•Users should be familiar with the assembly manual. This manual contains assembly guidance;
selected precautionary measures as well as recommendations for servicing and maintenance of the
product, in order to ensure a secured and fun use of the product.
•It is the responsibility of the owner or the supervisor to guarantee that all users of the product are
informed sufficiently of all warning references and safety instructions.
For the supervisor:
The supervisor’s role is to make sure users are aware of all safety precautions and that these precautions
are enforced. When a supervisor is not available, the product may be disassembled or covered to limit
access.
•The product can be only used if it is in good condition, worn or damaged parts should be replaced.
•Objects, which could be dangerous to the user, should be away from the product
•Avoid unauthorized and unsupervised use of the product.
•Do not use the product under influence of alcohol or drugs (incl. medicines).
•Do not use the product as a jumping platform for other articles.

8
3 ASSEMBLY INSTRUCTION

9
Not including timbers

10
RECOMMENDATIONS:
•The play structure must be securely assembled.
•For safety reasons, the cement cubes must be poured 5cm below ground level, at the frame’s outer
angles.
•The play structure must not be installed directly on cement, asphalt, or any other hard surface.
•Your play structure must be attached on a flat horizontal surface with a minimum of 2m between it
and any structure or obstacle such as a fence, garage house, tree branches, cloths lines, or electric
cables.
4 MAINTENANCE
WARNING: Please keep for future reference
We recommend regular maintenance to be conducted at the beginning of each season as well as at regular
intervals during the usage session for your play equipment to ensure all main parts/fixings are tightly
secured, well-oiled and intact to avoid failure, injury or hazards.
GENERAL ADVICE
It is of particular importance that this is followed at the beginning of each season as well as at regular
intervals during the usage season.
1. Check the accessories monthly as well as the play equipment’s structure in order to prevent falling
risks.
2. Check and retighten screws, bolts and all other hardware elements as necessary.
a. Do not over tighten to avoid damaging the thread or cracking the surrounding wood.
3. Check all coverings and bolts for sharp edges and replace when required.
4. Lubricate all moving metallic parts.
5. When signs of oxidation and / or rust appear on various metallic parts of your equipment, sand
rusted areas and tubular members and repaint using a non-lead based paint when required.