LifeSpan Kids Summit 2m Dome Climber User manual

Summit 2m Dome Climber
USER MANUAL
WARNING: The disassembled product may contain small parts
which pose a choking hazard to children under 3.
IMPORTANT:
The owner’s manual contains safety, assembly, use and maintenance instructions. This product must
be assembled by an adult who has read and understood these instructions. Keep the packaging away
from children and dispose of all packaging before use.
NOTE:
This manual should not be used to guide your purchasing decision. Your product, and the contents
inside its carton, may vary from what is listed in this manual. This manual may also be subject to
updates or changes. Updated manuals are available through our website at www.lifespankids.com.au.
For the installer and your children’s safety, it is important to fully read and understand the instructions
and safety hazards before commencing the assembly of the product.

TABLE OF
CONTENTS
WARNING
I. GENERAL SAFETY INSTRUCTIONS
1.1 Danger for Children
1.2 Risk of Injuries
1.3 Product Damage
1.4 Assembly Advice
II. SAFETY INSTRUCTIONS
III. PARTS LIST
IV. ASSEMBLY INSTRCUSTION
V. EXPLODED DIAGRAM
VI. SLIDE ATTACHMENT INSTRUCTION
VII. MAINTENANCE
VIII. WARRANTY
3
5
5
5
5
6
7
8
9
14
15
16
17

3
WARNING!
•This product must be assembled by an adult.
•Children must not use the product until properly installed.
•Not suitable for children under 3 years.
•Small parts. Choking Hazard.
•Max user 2 and Max user weight 50kgs.
•For outdoor and domestic use only.
•Maximum fall heights 900mm.
WARNING
1. The product should be installed over impact absorbing surfaces such as sand, wood-bar chips,
rubber and foam and should not be installed over concrete, asphalt or any hard surface.
2. Anchors shall be placed level with or under the ground in order to reduce tripping hazards.
3. If these checks are nor carried out, the toy could overturn or otherwise become a hazard. Oil all
metallic moving parts. Check all overrings and bolts for Sharpe edges and replace when required.
Check swing seats, chains, ropes, and other means of attachment for evidence of deterioration.
Replace when required in accordance with the manufacturer’s instructions. Sand rusted areas and
tubular members and repaint using a non-lead based paint when required.
4. Consumer Information Sheet for Playground Surfacing Materials The US Consumer Product Safety
Commission(CPSC) estimates that about 100 000 playground equipment-related injuries resulting
from falls to the ground surface are treated annually in US hospital emergency rooms. Injuries
involving this hazard pattern tend to be among the most serious of all playground injuries, and have
the potential to be fatal, particularly when the injury is to the head. The surface under and around
playground equipment can be a major factor in determining the injury-causing potential of a fall.
It is self-evident that a fall on to a shock-absorbing surface is less likely to cause a serious injury
than a fall onto a hard surface.Playground equipment should never be placed on hard surfaces,
such as concrete or asphalt, and while grass may appear to be acceptable, it may quickly turn
to hard-packed earth in areas of high traffic. Shredded bark mulch, wood chips, tine sand or the
gravel are considered to be acceptable shock absorbing surfaces when installed and maintained
at a sufficient depth under and around playground equipment. Table B.1 lists the maximum height
from which a child would not be expected to sustain a life-threatening head injury in a fall on to four
different loose-fill surfacing materials if they are Installed and maintained at depths of 150mm,
225mm and 300mm.

4WARNING
However, it should be recognized that all injuries due to falls cannot be prevented, no matter what
surfacing material is used.
It is recommended that a shock absorbing material extend a minimum of 1 800 mm in all directions
from the perimeter of stationary equipment such as climbing frames and slides. This information
is intended to assist in comparing the relative shock-absorbing properties of various materials. No
particular material is recommended over another. However, each material is only effective when
properly maintained. Materials should be checked periodically and replenished to maintain correct
depth as determined necessary for the equipment in question.
The choice of a material depends on the type and height of the playground equipment, the
availability of the material in a particular area, and its cost.
Table B.1 Fall height in millimetres from which a life-threatening head injury would not be expected.
Type of Material
Depth of surfacing material
150mm 225mm 300mm
Double Shredded Bark Mulch 1800 3000 3300
Wood Chips 1800 2100 3600
Fine Sand 1500 1500 2700
Fine Gravel 1800 2100 3000

5
I. GENERAL SAFETY INSTRUCTIONS
1.1 DANGER FOR CHILDREN
WARNING: No eating while using the product.
•Children do not recognize potential dangers from this product. The product must be stored
out of reach of children and pets.
•This product may only be used with adult supervision at all times.
•The packaging material is not suitable for children due to choking and suffocation hazards.
•Do not use the product if it is damaged or defective. If it is damaged or defective, please
contact a qualified technician.
•Check the product before each use. Defective parts must be changed immediately as they
can impair the function and the safety of the product.
•No more than one person to use the product at the same time.
•Use the product only on even and non-slipping surfaces. Never use it near water and keep
sufficient space around for safety.
•Beware of moving parts such as the springs or elastics, which could catch your arms and
legs. Do not place any objects or body parts in the product’s openings.
•Do not make alterations to the product. Only use original spare parts. Qualified technicians
should only carry out repairs – improper repairs can lead to danger for the user. Use this
product only as described in this manual.
•Protect the product against splashes, humidity, high temperature and direct sunlight.
1.2 RISK OF INJURIES
1.3 PRODUCT DAMAGE
GENERAL SAFETY INSTRUCTIONS

6
• The assembly of the product must be done carefully and by an able-bodied adult. If in any
doubt, ask a technically qualified person.
• Before you start with the assembly, read the instructions carefully.
• Remove all packaging materials and lay down all parts on an open space. This gives you
an overview and simplifies the assembly procedure.
• Check with the parts list that all parts are available. Dispose of the packaging material when
the assembly is completed.
• Beware that when using tools or doing technical work, there is always a risk of injuries.
Assemble the product with care.
• Create a danger free environment; for example, do not let tools lay around the workspace.
Store the packaging material in a way that cannot cause any danger.
• After installing the product according to the instruction manual, en sure all screws, bolts and
nuts are correctly installed and tightened and that all joints are secure.
• Reasonable space must be kept between the product and possible sources of danger, such
as other equipment swimming pools and fences.
• The product must be assembled correctly before use.
• Place the product on a level surface at least 2 m from any structure or obstruction such as a
fence, garage or house.
• Modifications made to the original product shall be carried out according to the instructions
of the manufacturer.
• The product must always be used in a well-lit area.
• Do not place anything under the product.
• Use gloves during assembly and disassembly.
• Outdoor products should be equipped with a device that in strong wind conditions
avoid displacement due to wind (e.g. steel bars in the ground or loads like sand bag or water
bags).
• In certain areas during winter, snow buildup and the low temperatures can damage the
product. It isrecommended to remove snow buildup and to store the product indoor.
• We strongly recommend visual inspections every 3 months to insure the integrity of the
entire product. Replace any parts as necessary.
1.4 ASSEMBLY ADVICE
GENERAL SAFETY INSTRUCTIONS

7
•The safety instructions of the product should always be considered and obeyed.
• Using the product may result in permanent injury such as paralysis, or even death. Falling off the
product may lead to injuries, particularly to the back, neck or head.
• No clothes with hooks or lose parts should be worn or carried during product usage in order to
avoid hooks getting caught and causing injury.
•Strong winds can result in the product being blown away or damaged. If strong winds are
predicted the product must be disassembled and moved to a sheltered area or sufficiently
anchored down.
•Moving the product whilst assembled may affect the integrity of the frame. Should it be necessary
to move the product, please consider the following:
1. Force to be evenly spaced around the frame to lift the product off the ground
2. The product must be carried horizontally
3. Use caution whilst moving as it could bend the product frame.
•Users should be familiar with the assembly manual. This manual contains assembly guidance;
selected precautionary measures as well as recommendations for servicing and maintenance
of the product, in order to ensure a secured and fun use of the product.
•It is the responsibility of the owner or the supervisor to guarantee that all users of the product
are informed sufficiently of all warning references and safety instructions.
•The product can be only used if it is in good condition, worn or damaged parts should
be replaced.
•Objects, which could be dangerous to the user, should be away from the product.
•Avoid unauthorized and unsupervised use of the product.
•Do not use the product under influence of alcohol or drugs (incl. medicines).
•Do not use the product as a jumping platform for other articles.
The supervisor’s role is to make sure users are aware of all safety precautions and that these
precautions are enforced. When a supervisor is not available, the product may be disassembled or
covered to limit access.
For the supervisor
II. SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS

8
III. PARTS LIST
PARTS LIST
#1 6-holes Bracket
(Qty 4)
#2 6-holes Bracket
(Qty 4)
#3 4-holes Bracket
(Qty 8)
#4 5-holes Bracket
(Qty 4)
M8X15mm Allen Bolt
with M8 Domed
nylock nut (Qty 92)
M8X30mm Allen Bolt
with M8 Domed
nylock nut (Qty 8)
M8x40mm Allen Bolt ,
spring washer and
M8 bolt Nut (Qty 14)
M8X40mm Allen Bolt (Qty 2) Anchor (Qty 3)
Key No. Description Qty
1 Frame #A 16
2 Frame #B 8
3 Frame #C 8
4 Frame #D 4
5 Platform Frame #5 2
6 Platfrom Frame #6 2
7 Platform Frame #7 7
8 Barrier Frame #8 2
9 Barrier Rung #9 1

9
ASSEMBLY INSTRUCTIONS
IV. ASSEMBLY INSTRUCTION
Tools Required Assembling the equipment: One Adjustable Wrench and one Allen Wrench
NOTE: It is strongly recommended two or more people assembling this equipment to avoid
possible injury.
STEP 1 (See diagram 1)
A. Attach two Frames (#A) to the upper two holes on a 6-hole Bracket (#1). Attach two Frames (#A)
to the lower two holes on the same 6-hole Bracket (#1). Make sure the Frames are behind the
Bracket as shown in Diagram-1 below.
B. Secure each Frame to the Bracket with one M8 x 15MM Allen Bolt and M8 Domed nylock Nut.
Do not fully tighten the Nut and Bolt yet.
C. Repeat Procedures A & B above to assemble Three more sets (Total four sets) and let’s call it
“Frame X” for easier identification.
DIAGRAM 1
#A
#1
#A

10 ASSEMBLY INSTRUCTIONS
STEP 2 (See diagram 2)
A. Attach five Frames (#B -2PCS, #C- 2PCS,#D-1PC) to a 6-hole Bracket (#2).
B. Please take note of Frames (#D) - the 2 holes end must fix to the corresponding position on
6-hole Bracket (#2).
C. Secure each Frame to the Bracket with one M8 x 15MM Allen Bolt and M8 Domed nylock Nut.
D. Do not fully tighten the Nut and Bolt yet.
E. Repeat Procedures A & B & C above to assemble Three more Frame-Y (Total four sets).
DIAGRAM 2
STEP 3 (See diagram 3)
A. Connect a Frame (#E) to a 4-hole Bracket (#3) and secure them with one M8 x 15MM Allen Bolt
and M8 Domed nylock Nut. Do not fully tighten the Nut and Bolt yet.
B. Connect other seven Frames (#E) together to form a big circle (Frame Z) using Eight 4-hole
Brackets (#3).
DIAGRAM 3
#D #C
#2
#C
#B
2-holes end



#E
#3

11
ASSEMBLY INSTRUCTIONS
STEP 4 (See diagram 4)
A. Connect two lower beams (#A) on a Frame-X to the 4-hole Brackets (#3) on Frame-Z.
B. Secure each hole with one M8 x 15MM Allen Bolt and M8 Domed nylock Nut. Do not fully tighten
the Nut and Bolt yet.
C. Connect two lower beams(#B) on a Frame-Y to the adjacent hole on the same 4-hole Bracket
(#3) on Frame Z.
D. Repeat procedures above to install all the Frame-X and Frame-Y onto Frame Z to form a
hemisphere.
E. Connect two side beams (#C) on a Frame-Y to the 6-hole Brackets (#1) together horizontally.
F. Connect two upper beams (#B) on a Frame-X and the beam (#E) on a Frame-Y to the adjacent
hole on the 5-hole Bracket (#4).
G. Secure each hole with one M8 x 15MM Allen Bolt , and M8 Domed nylock Nut. Do not fully tighten
the Nut and Bolt yet.
H. Then repeat the step (F & G) to build rests of frames.
DIAGRAM 4
#4
#A
#D
#1
#2
#C
#A
#1
#B
#A
#C
#D
#1
#B

12 ASSEMBLY INSTRUCTIONS
STEP 5 (See diagram 5)
A. Start to build the top platform, connect two Frames (#5) underneath the Brackets (#4), then
connect two Frames (#6) on the Brackets (#4) on the other sides.
B. Secure each hole with one M8 x 30MM Allen Bolt, and M8 Domed nylock Nut. Do not fully tighten
the Nut and Bolt yet.
DIAGRAM 5
STEP 6 (See diagram 6)
A. Connect other platform Frames(#7) on Frame (#5).
B. Secure each hole with one M8 x 40MM Allen Bolt, spring washer and M8 bolt Nut. Do not fully
tighten the Nut and Bolt yet.
DIAGRAM 6
#4
#6
#6
#5
#5
#7

13
ASSEMBLY INSTRUCTIONS
STEP 7 (See diagram 7)
A. Insert 2 barrier frames( #8) into the joints on bracket(#4), ensure the pop-pin in proper position.
B. User the frame (#9) to connect two barrier frames (#8) together, Secure each end with
M8 x 40MM Allen Bolt . Do not fully tighten the Nut and Bolt yet.
C. Now set the entire unit firmly on the ground and align all the frames. Make adjustment if
necessary.
D. You can now securely tighten all Nuts and Bolts previously installed.
DIAGRAM 7
#8
#9

14 EXPLODED DIAGRAM
V. EXPLODED DIAGRAM
ATTENTION
Product must be securely anchored
before use to prevent the equipment
from tipping over and movement.

15
SLIDE ATTACHMENT INSTRUCTION
VI. SLIDE ATTACHMENT INSTRUCTION
WARNING!
This product must be assembled by an adult.
Children must not use the product until properly installed.
May contain hazardous sharp objects & small parts.
Not suitable for children under 3 years. Choking hazard.
OPTIONAL: Slides sold separately or in a set. Bolt 2
Bolt 1
BR9
Bolt 2
Bolt 1
BR9
M8X47MM 2PCS
M8X30MM 2PCS
1. Connect BR9 to the climber Frame as picture shown, Secure each end with Bolt 1 M8 x 47MM Allen
Bolt and tighten the nut properly.
2. Attached the slide on BR9 Bracket, secure it with Bolt 2 M8 x 30MM Allen bolt and tighten the
nut properly.

16 MAINTENANCE
VII. MAINTENANCE
WARNING: Please keep for future reference.
We recommend regular maintenance to be conducted at the beginning of each season as well as at
regular intervals during the usage session for your play equipment to ensure all main parts/fixings are
tightly secured, well-oiled and intact to avoid failure, injury or hazards. Failure to check this could result in
equipment becoming a hazard or overturning.
GENERAL ADVICE
It is of particular importance that this is followed at the beginning of each season as well as at regular
intervals during the usage season.
•Check the accessories monthly as well as the play equipment’s structure in order to prevent
falling risks.
•Check and retighten screws, bolts and all other hardware elements as necessary.
a. Do not over tighten to avoid damaging the thread or cracking the surrounding wood.
•Check all coverings and bolts for sharp edges and replace when required.
•Lubricate all moving metallic parts.
• When signs of oxidation and / or rust appear on various metallic parts of your equipment, sand
rusted areas and tubular members and repaint using a non-lead based paint when required.
• Where applicable: check swing seats, chains, ropes, and other means of attachment for evidence
of deterioration.
•Sand off any rough edges or splinters and re-strain/paint the wood to prevent larger splits.
•Replace when required in accordance with the owner’s manual.
If your play structure is disassembled, be sure to clearly mark any attached metal plates to prevent
accidents. Check all bolt covers and sharp edges and replace them if necessary.
For longer accessory life, we suggest storing them during the winter.

17
WARRANTY
VIII. WARRANTY
AUSTRALIAN CONSUMER LAW
Many of our products come with a guarantee or warranty from the manufacturer. In addition, they come
with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and compensation for any other reasonably foreseeable loss
or damage.
You are entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure. Full details of your consumer rights may be found at
www.consumerlaw.gov.au.
Please visit our website to view our full warranty terms and conditions:
www.lifespankids.com.au/Warranty-Policy-Kids
WARRANTY AND SUPPORT
Any claim against this warranty must be made through your original place of purchase. Proof of
purchase is required before a warranty claim may be processed. If you have purchased this product
from the Official Lifespan Kids website, please visit www.lifespankids.com.au/warranty-form
For support outside of warranty, if you wish to purchase replacement parts or request a repair or service,
please visit www.lifespankids.com.au/warranty-form and fill in our Repair/Service Request Form or
Parts Purchase Form.

www.lifespankids.com.au