Lightforce Enforcer 140 LED User manual

The new Enforcer 140 LED handheld introduces Fresnel technology to the sporting market. The specially designed
lens produces a superior tight beam for maximum light output and performance. The internal battery has a run
time up to 4 hours and you can even attach the clip on Enforcer battery to produce an extended runtime of up to
18.5 hours. Combined with a lightweight ergonomic grip and an inbuilt battery indicator the new LED Enforcer 140
will provide the ultimate sporting experience.
RECOMMENDATIONS:
1. Replace rear protective seal on base of handle after charging to maintain IP rating.
2. Ensure all electrical connectors are secure - loose connections will generate excessive heat, damage wiring and
cause electrical failure.
3. The outer lens should be washed clean with copious amounts of water and a clean sponge. Wiping it with a dry
rag will scratch the lens, especially if the surface is dusty. NEVER clean the light with cleaning uid or solvent.
4. DO NOT attempt to clean the inside of the light or touch the inside lens.
5. Never remove the reector housing from the handle. The LED and lens inside are delicate and should never be
exposed to dust or handled.
6. Reector housing should never be adjusted so two O-rings are visible, otherwise light will not maintain IP
rating.
BATTERY & CHARGING:
Charge the battery fully before rst use.
Select required adaptor and t on to mains charger.
Remove protective cover on base of handle and connect included universal AC mains charger’s DC plug in to DC
input on handle.
Connect AC charger to wall outlet.
The Enforcer LED 140 has a run time of 4 hours at 25°c. After this time, the light will enter ‘reserve’ mode,
allowing up to a further 1 hour at a reduced light output.
The Enforcer LED 140 can be charged via the supplied 100-240V universal AC to 12V DC charger or optional
Lightforce SLA and LiFePO4 battery packs as well as direct from vehicle.
The light can be operated while simultaneously being charged while connected to an external 12v DC supply.
Do not operate the light while charging from the AC wall charger.
The Enforcer LED 140 has an inbuilt charging circuit designed for 12v ONLY. Never connect the light to any power
source other than 12v.
The charge indicator in the base of the light will illuminate for 2 seconds once pressed.
If battery is to be stored for a long period of time, ensure battery has at least 50% charge.
The unit must be returned to a service agent for battery replacement.
SPECIFICATIONS:
490 grams / 17.28 ounces
IP65 ingress protected
IR LED: Wave length: 850nm
Red: 4hr runtime plus up to 1 hour of reserve mode @ 25 degrees
IR: 3 hours run time at maximum intensity
Maximum charge time being 2.5 hours
Red / IR Enforcer LED 140 Instructions
LIGHTFORCE AUSTRALIA PTY LTD • 11 Manton Street, Hindmarsh SA 5007 Australia • www.lightforce.com | email: [email protected]
Australia: Tel: [phone] | Fax: [phone] • Int’l: Tel: [phone] | Fax: [phone]
All logos and images are subject to relevant trademark and copyright protection LIGHTFORCE Pty Ltd | © AUGUST 2016 • Data and specications contained maybe subject to change without notice.
LIGHTFORCE Australia Pty Ltd shall not be liable for damage, malfunction, failure resulting from accident, misuse, misapplication, unauthorised repair, neglect, modication, unauthorised or non standard replacement parts,
accessories, bulbs, batteries or voltage or operation of the product beyond its technical and or environmental specication.
INSTRUCTION DATA
PRODUCT: RED / IR ENFORCER LED 140
VER: 1.0
DATE: AUGUST 2016

Charging Status Charging Status
All Off Fully charged (100%)
Flashing
Green
60%
Flashing
Amber
30%
Flashing Red Less than 5%
INSTRUCTION DATA
PRODUCT:RED / IR ENFORCER LED 140
VER: 1.0
DATE: AUGUST 2016
LIGHTFORCE AUSTRALIA PTY LTD • 11 Manton Street, Hindmarsh SA 5007 Australia • www.lightforce.com | email: [email protected]
Australia: Tel: [phone] | Fax: [phone] • Int’l: Tel: [phone] | Fax: [phone]
All logos and images are subject to relevant trademark and copyright protection LIGHTFORCE Pty Ltd | © AUGUST 2016 • Data and specications contained maybe subject to change without notice.
LIGHTFORCE Australia Pty Ltd shall not be liable for damage, malfunction, failure resulting from accident, misuse, misapplication, unauthorised repair, neglect, modication, unauthorised or non standard replacement parts,
accessories, bulbs, batteries or voltage or operation of the product beyond its technical and or environmental specication.
The dimmer lever has dual functionality. Constant red is achieved with the lever in the up position. Moving
the lever down changes light output to minimum IR and maximum IR intensity is achieved in the down
position.
Operation of the variable power light at reduced brightness levels saves power and extends battery life.
DESIRED FOCUS
ROTATE FOR
- RED
- IR
to high intensity IR
GORE PROTECTIVE VENT
CHARGING PORT

LIGHTFORCE AUSTRALIA PTY LTD • 11 Manton Street, Hindmarsh SA 5007 Australia • www.lightforce.com | email: [email protected]
Australia: Tel: [phone] | Fax: [phone] • Int’l: Tel: [phone] | Fax: [phone]
All logos and images are subject to relevant trademark and copyright protection LIGHTFORCE Pty Ltd | © AUGUST 2016 • Data and specications contained maybe subject to change without notice.
LIGHTFORCE Australia Pty Ltd shall not be liable for damage, malfunction, failure resulting from accident, misuse, misapplication, unauthorised repair, neglect, modication, unauthorised or non standard replacement parts,
accessories, bulbs, batteries or voltage or operation of the product beyond its technical and or environmental specication.
INSTRUCTION DATA
PRODUCT:RED / IR ENFORCER LED 140
VER: 1.0
DATE: AUGUST 2016
Voltage Indicator Runtime (Full Intensity)
4 hours
Flashing
Green
3.8 hours
2.8 hours
1 hour
Flashing Red 10 minutes - reserve mode follows
Charging Status Charging Status
All Off Fully charged (100%)
Flashing
Green
60%
Flashing
Amber
30%
Flashing Red Less than 5%
Internal handheld battery will charge when connected to 12V DC power. Please note that battery charge indicator does not
work whilst light is turned on.
RoHS Compliant
3 year warranty (excluding internal battery)
INTERNAL BATTERY: Li-Ion Polymer, 2Ah battery 14.8Wh - Built in LED charge level indicators - Built in LED charging status
indicators - UN38.3 certied
KIT CONTENTS: 1 x 100-240V universal AC to 12V DC power supply 1 x Enforcer LED 140 handheld light
OPTIONAL ACCESSORIES:
Compatible with the Lightforce Ni-MH Enforcer battery (BPEF). This provides an extended runtime of up to 18.5 hours
Enforcer mounting bracket (EFMB)
Cord options:
• 2m coil cord with merit plug for use with Lightforce SLA or LiFePO4 battery packs (SLCORDCP)
• Figure 8 ex with alligator clips for direct battery connection (SLCORDAC)
The dimmer lever has dual functionality. Constant red is achieved with the lever in the up position. Moving
the lever down changes light output to minimum IR and maximum IR intensity is achieved in the down
position.
Operation of the variable power light at reduced brightness levels saves power and extends battery life.
- IR

Enforcer LED 140 Instructions
LIGHTFORCE AUSTRALIA PTY LTD • 11 Manton Street, Hindmarsh SA 5007 Australia • www.lightforce.com | email: [email protected]
Australia: Tel: [phone] | Fax: [phone] • Int’l: Tel: [phone] | Fax: [phone]
All logos and images are subject to relevant trademark and copyright protection LIGHTFORCE Pty Ltd | © AUGUST 2016 • Data and specications contained maybe subject to change without notice.
LIGHTFORCE Australia Pty Ltd shall not be liable for damage, malfunction, failure resulting from accident, misuse, misapplication, unauthorised repair, neglect, modication, unauthorised or non standard replacement parts,
accessories, bulbs, batteries or voltage or operation of the product beyond its technical and or environmental specication.
INSTRUCTION DATA
PRODUCT:RED / IR ENFORCER LED 140
VER: 1.0
DATE: AUGUST 2016
WARRANTY
Australia
“Lightforce” means Lightforce Australia Pty Ltd ABN 54 069 439 774 Address: 11 Manton Street, Hindmarsh, SA, 5007.
Telephone:[phone]. Email Address: [email protected]
“Lightforce Afliates” means Lightforce, Lightforce’s related bodies corporate (within the meaning of the Corporations Act 2001),
and their respective employees, ofcers, agents and contractors.
“Warranty Period” means:
(a) For Lightforce products (excluding bulbs and batteries, Custom Built products and mounts and Ace Precision Rie Systems
products) manufactured in Australia and sold either in Australia or overseas, three (3) years from the date of purchase specied
on your sales receipt or invoice unless otherwise notied by Lightforce in writing prior to or at the date of purchase;
(b) For
1) Lightforce products and accessories manufactured outside, but imported into, Australia; and
2) Custom Built products and mounts (wherever manufactured);
3) Sold in Australia or overseas (but in each case excluding bulbs and batteries, and Ace Precision Rie Systems products),
one (1) year from the date of purchase specied on your sales receipt or invoice unless otherwise notied by Lightforce in writing
prior to or at the date of purchase.
What this warranty covers:
Lightforce warrants that it will, at its option, replace or repair each product that you purchase which, during the warranty period,
has a defect in materials or workmanship under normal use and conditions.
Statutory rights:
Our products come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the products repaired or replaced if the products fail to be of acceptable quality and the failure does not amount
to a major failure.
In addition, the benets given by this warranty are in addition to your rights and remedies under a law in relation to the
products.
Replacement of a product or parts:
When warranty service involves the replacement of a product or a part, the replaced product or part becomes Lightforce’s
property. Only unaltered Lightforce products and parts are eligible for replacement. The replacement product or part is warranted
for the balance of the period remaining on the original product. Products and parts presented for repair may be replaced by
refurbished product or parts of the same type rather than being repaired or replaced with new parts.
Procedure for claiming:
Australia: Make contact with the Lightforce sales ofce at the above address. We will attempt to resolve the issue over the
phone, or we may issue a warranty case notice to arrange return of the product for assessment. Lightforce will not be able to
perform our service under this warranty if you refuse to return the product to us for inspection.
Claims in respect of defects covered by this warranty must be made as soon as possible after such defect becomes apparent and,
in any event, not later than thirty (30) days after the end of the Warranty Period.
International: Contact the point of purchase for warranty service
Cost of claiming:
Under this warranty and, unless Lightforce otherwise agrees in writing, you bear the cost of claiming under this warranty
including the cost of returning the product to Lightforce.
Under this warranty, Lightforce is responsible for loss or damage to your product only while it is in the possession of Lightforce
Afliates.
Use of personal information:
This warranty will not apply if you do not supply to us or to our Lightforce Afliates information that we reasonably request to
enable us to perform our obligations under this warranty. You have the right to access your personal contact information and
request correction of any errors in it pursuant to the Privacy Act 1988 by contacting Lightforce.