lilitab Floor Pro User manual

39 Larkspur Street | Suite B t: 888.705.0190 San Rafael, CA 94901 e: [email protected] www.lilitab.com
Lilitab Floor Pro Mount
Assembly Instructions
v4.0

Lilitab Floor Pro Mount Assembly Instructions v4.0 2
TABLE OF CONTENTS
Assembly Preparation and Packing List.....................3
Features .............................................. 4
Assembly Instructions ................................... 5
Bolt Down Installation ...................................6
GOT QUESTIONS? WE’RE HERE TO HELP!
EMAIL [email protected]om PHONE [phone]
Scan to watch
assembly video!

Lilitab Floor Pro Mount Assembly Instructions v4.0 3
MOUNT ASSEMBLY PREPARATION
FOR BASE PLATE INSTALLATION, YOU’LL NEED:
4 Phillips screwdriver
FOR BOLT DOWN INSTALLATION, YOU’LL NEED:
4 Powered drill/driver, preferably with impact action
4 Socket wrench with a neck of at least 5”, this may require
a socket extension
4 2 x bolts, wood screws or other fastener suitable for your
floor’s substrate (m6, no.14 or 1/4” diameter)
TO SECURE YOUR LILITAB YOU WILL NEED:
4 Kensington compatible cable lock
PACKING LIST
1 x Floor Pro Mount
1 x Foot Cover
(If ordered without Floor Base)
2 x MagDOCK Keys
1 x Silver L Key
1 x Black L Key
1 x Floor Base
1 x Base Housing
2 x M6x12mm Base Screws
(short)
2 x M6x14mm Base Screws
(long)
2 x M3x6mm Base Security
Screws
INCLUDED
INCLUDED IF YOU ORDERED FLOOR BASE

Lilitab Floor Pro Mount Assembly Instructions v4.0 4
FEATURES
MULTI-POSITION NECK JOINT
Permits tilt up/down. It has two
operator configurable modes:
Fixed. The Head Unit can
be set to any fixed angle
between completely
vertical and +/-22.5.°
Tilt. Can be configured to
allow the user to tilt the
Head Unit.
2 X M4 ACCESSORY MOUNT POINTS
Accepts Backdrop Graphic
LOCK POINT
Accepts kensington lock
MAGDOCK
With the turn of a key, the operator
can dock/undock the Lilitab Head
Unit. When the Head Unit is docked it
automatically begins charging and it
can be docked in any orientation.
USB CABLE SLOT
For peripherals
FLOOR BASE
Optional
BASE HOUSING FOR
TABLET’S AC ADAPTER
Included with optional
floor base
Head Unit shown for illustrative
purposes only. Your Head Unit may
vary depending upon your tablet
choice. Please refer to your Head
Unit instructions for more details.
All Lilitab Head Units do not
cause radio interference.

Lilitab Floor Pro Mount Assembly Instructions v4.0 5
ASSEMBLY INSTRUCTIONS
5. Place your Head Unit onto the MagDOCK
in either landscape or portrait orientation.
Turn the key to lock it in place.
WARNING: Not locking the MagDOCK will result in
the unit falling off, possibly damaging the unit and/
or the tablet. The Lilitab Pro is designed to be
operated with the lock closed.
6. Tilt feature. By default the Lilitab Head
Unit can be tilted by the user to suit. If
you wish to disable tilt, position your head
unit at the desired angle and tighten the
bottom screw on the neck joint with the
black L key provided.
Refer to your Lilitab Head Unit owner’s
manual for tablet installation instructions.
3. Connect and position cables:
1. Connect the charge cable to the tablet’s
AC adapter. Then connect the adapter
to your extension cord.
2 . Position both cables underneath the
base housing’s two plastic tabs. The
extension cord should exit the rear of
the housing.
3 . Screw down the base housing using the
two (2) M6x14mm long base screws.
4. Attach the base housing cover by sliding
it into place. Secure it using the two (2)
M3x6mm base security screws and
silver L key.
1. Thread the charge cable that came with
your kiosk through the top of the mount
pole. Insert the mount pole into the base
housing on an angle to clear the welded
flange, as pictured.
2. Attach Floor Base. Line up the bottom of the
mount pole with the four screw holes. Using
the two (2) M6x12mm short base screws,
secure through the two rear-most openings
closest to the cable egress slot.
NOTE: You will need to hold the base housing up
and out of your way while bolting. If not using the
floor base, attach to floor surface using template on
page 6, and thread the cable through your substrate.
(iPad AC adapter shown with optional apple
power extension cord. Your AC adapter will
vary depending upon your tablet type.)

Lilitab Floor Pro Mount Assembly Instructions v4.0 6
Mounting pattern
The Lilitab Floor Pro can be mounted
directly to any hard floor surface using
2 x bolts, wood screws or other fastener
suitable for your floor’s substrate (m6,
no.14 or 1/4” diameter). Use the mounting
pattern to the right for proper alignment.
BOLT DOWN INSTALLATION
1.50
38.10
1.50
38.10
4X M6 OR
1/4-20
1.63
41.44
.71
18
SLOT FOR
POWER CABLE:
USB TYPE A,
~12" PIGTAIL
Power supply cable
can run under or on
top of floor.