LINEAR LEDS LTL.PL363Z User manual
Linear Technologie • 11 rue du Puits Rochefort • 42 100 Saint-Etienne
Tél: +33 (0)4 77 81 49 49 • Fax: +33 (0)4 77 81 49 40 • www.lineartech.fr V.2017
36x3W LED PROJECTOR LTL.PL363Z
Operation manual
2
1. About this product
2. Safety instructions
3. Dimensions
4. DMX control
5. Control panel and menu
6. Operation instructions
7. Master / slave mode
8. Signal cable connection
9. Connection diagram
10. Specications
Page 3
Page 3
Page 3
Page 4
Page 4
Page 5
Page 5
Page 5
Page 6
Page 7
TABLE OF CONTENTS
3
• High quality LED, low consumption, RGB
• Dimmer 0 - 100%
• Strobe
• DMX512
• Auto-run, sound active, master / slave
• Zoom 10° - 60°
• 7 DMX channels
1. ABOUT THIS PRODUCT
This LED projectorPL363Z is equiped with red, green and blue LED, low consuption. Each
color can be independently adjusted. It ambeds dimmer functions, strobe, zoom, ...
2. SAFETY INSTRUCTIONS
• Observe the rated voltage of the device
• Check that the device has not been damaged during transportation
• This projector is designed for indoor or outdoor use. The ambient temperature must not
exceed 50 °C
• Install the projector in a well ventilated area and away from ammable materials (at least
50 cm)
3. DIMENSIONS
4
4. DMX CONTROL
CHANNEL VALUE FUNCTION
1 0 - 255 Dimmer for all color
2 0 - 255 Red gradation 0 - 100%
3 0 - 255 Green gradation 0 - 100%
4 0 - 255 Blue gradation 0 - 100%
5 0 - 5 Gradation
5 6 - 125 Strobe mode
5 126 - 255 Strobe
6 0 - 255 Macro
7 0 - 255 Zoom 60° - 10°
5. CONTROL PANEL AND MENU
MENU UP DOWN ENTER
DMX IN DMX OUT MENU : To access the menu or return to a previous option
UP
DOWN
ENTER : Select option or accept
6. OPERATION INSTRUCTIONS
This projector has 5 dierent modes :
Mode 1 : DMX MODE
1. Press MENU or UP/DOWN until appear A001
2. Press ENTER, the display will ash
3. Press UP/DOWN to change the code address A001 to A512
4. Press again ENTER the display will stop ashing and save mode. During startup,
the settings are automatically applied.
7. MASTER / SLAVE MODE
Master : Can be programmed for all modes except DMX. It sends the signal to the slaves
which synchronize with the master.
Congure slave lights in the DMX mode.
5
8. SIGNAL CABLE CONNECTION
Connect the male plug to the female plug as below :
Note : To avoid transmission errors and signal interference, put a 120 Ω resistor (1 / 4W) as
shown below, end of the line DMX :
3-pin and 5-pin : If the DMX512 controller is 5-pin, use a signal cable which transfers the
5-pin in 3-pin.
9. CONNECTION DIAGRAM
6
10. SPECIFICATIONS
• 220 - 240V
• Power supply : 120W maxi
• 3W LED
• 36 red LED 1W, 36 green LED 1W, 36 blue LED 1W
• DMX512, auto-run
• Stand alone, master / slave
• 7 DMX channels
• Zoom 15° - 60°
• Dimensions : 275 x 275 x 410 mm
• Weight : 6 kg
Linear Technologie • 11 rue du Puits Rochefort • 42 100 Saint-Etienne
Tél: +33 (0)4 77 81 49 49 • Fax: +33 (0)4 77 81 49 40 • www.lineartech.fr
Table of contents
