LINEAR SOUND LTS.CDP User manual
Linear Technologie • 11 rue du Puits Rochefort • 42 100 Saint-Etienne
Tél: +33 (0)4 77 81 49 49 • Fax: +33 (0)4 77 81 49 40 • www.lineartech.fr V.2017
MP3 CD PLAYER LTS.CDP
Operation manual
Please follow the instructions in this manual to obtain the optimum results from this unit.
We also recommend that you keep this manual handy for future reference.
2
1. Safety precautions
2. General description
3. Features
4. Nomenclature and functions
a. Front panel
b. Rear panel
5. CD operation
6. Applications
7. Specications
8. Dimensional diagram
Page 3
Page 5
Page 5
Page 5
Page 6
Page 6
Page 6
Page 7
TABLE OF CONTENTS
3
• Be sure to read the instructions in this section carefully before use.
• Make sure to observe the instructions in this manual as the conventions of safety
symbols and messages regarded as very important precautions are included.
• We also recommend you keep this instruction manual handy for future reference.
Safety symbol and message conventions
Safety symbols and messages described below are used in this manual to prevent bodily
injury and property damage which could result from mishandling. Before operating your
product, read this manual rst and understand the safety symbols and messages so you are
thoroughly aware of the potential safety.
1. SAFETY PRECAUTIONS
WARNING Indicates a potentially hazardous situation which, if mishandled,
could result in death or serious personal injury.
CAUTION
Indicates a potentially hazardous situation which, if mishandled,
could result in moderate or minor personal injury, and/or property
damage.
Warning
When installing the unit
• Do not expose the unit to rain or an environment where it may be splashed by water or
other liquids,as doing so may result in re or electric shock.
• Use the unit only with the voltage specied on the unit. Using a voltage higher than that
which is specied may result in re or electric shock.
• Do not cut, kink, otherwise damage nor modify the power supply cord. In addition,
avoid using the power cord in close proximity to heaters, and never place heavy objects
(including the unit itself) on the power cord, as doing so may result in re or electric
shock.
• Be sure to replace the unit’s terminal cover after connection completion. Because high
voltage is applied to the speaker terminals, never touch these terminals to avoid electric
shock.
• Be sure to ground to the safety ground (earth) terminal to avoid electric shock. Never
ground to a gas pipe as a catastrophic disaster may result.
• Avoid installing or mounting the unit in unstable locations, such as on a rickety table or a
slanted surface. Doing so may result in the unit falling down, causing personal injury and
/ or property damage.
When the unit is in use
• Should the following irregularity be found during use, immediately switch o the power,
disconnect the power supply plug from the AC outlet and contact your nearest dealer.
Make no further attempt to operate the unit in this conditions this may cause re or
electric shock, ...
- If you detect smoke or a strange smell coming from the unit.
- If water or any metallic object gets into the unit.
- If the unit falls, or the unit case breaks.
- If the power supply cord is damaged (exposure of the core, disconnection, etc)
- If it is malfunctioning (no tone sounds)
4
• To prevent a re or electric shock, never open or remove the unit case as there are high
voltage components inside the unit. Refer all servicing to your nearest dealer.
• Do not place cups, bowls, or other containers of liquid or metallic objects on top of the
unit. If they accidentally spill into the unit, this may cause a re or electric shock.
• Do not insert nor drop metallic objects or ammable materials in the ventilation slots of
the unit’s cover, as this may result in re or electric shock.
Caution
When installing the unit
• Never plug in nor remove the power supply plug with wet hands, as doing so may cause
electric shock.
• When unplugging the power supply cord, be sure to grasp the power supply plug; never
pull on the cord itself. Operating the unit with a damaged power supply cord may cause
a re or electric shock.
• When moving the unit, be sure to remove its power supply cord from the wall outlet.
Moving the unit with the power cord connected to the outlet may cause damage to the
power cord, resulting in re or electric shock. When removing the power cord, be sure to
hold its plug to pull.
• Do not block the ventilation slots in the unit’s cover. Doing so may cause heat to build up
inside the unit and result in re.
• Avoid installing the unit in humid or dusty locations, in locations exposed to the direct
sunlight, near the heaters, or in locations generating sooty smoke or steam as doing
otherwise may result in re or electric shock.
When the unit is in use
• Should the following irregularity be found during use, immediately switch o the power,
disconnect the power supply plug from the AC outlet and contact your nearest dealer.
Make no further attempt to operate the unit in this conditions this may cause re or
electric shock, ...
• To prevent a re or electric shock, never open or remove the unit case as there are high
voltage components inside the unit. Refer all servicing to your nearest dealer.
• Do not place cups, bowls, or other containers of liquid or metallic objects on top of the
unit. If they accidentally spill into the unit, this may cause a re or electric shock.
• Do not insert nor drop metallic objects or ammable materials in the ventilation slots of
the unit’s cover, as this may result in re or electric shock.
• Do not place heavy objects on the unit as this may cause it to fall or break which may
result in personal injury and/or property damage. In addition, the object itself may fall o
and cause injury and / or damage.
• Make sure that the volume control is set to minimum position before power is switched
on. Loud noise produced at high volume when power is switched on can impair hearing.
• Do not operate the unit for an extended period of time with the sound distorting. This is
an indication of a malfunction, which in turn can cause heat to generate and result in a
re.
• Contact your dealer as to the cleaning. If dust is allowed to accumulate in the unit over a
long period of time, a re or damage to the unit may result.
• If dust accumulates on the power supply plug or in the wall AC outlet, a re may result.
Clean it periodically. In addition, insert the plug in the wall outlet securely.
• Switch o the power, and unplug the power supply plug from the AC outlet for safety
purposes when cleaning or leaving the unit unused for 10 days or more. Doing otherwise
may cause a re or electric shock.
5
The CDP is a public address amplier switch with can provide an ideal public address
solution from small to big places such us mosques, schools, hotels and factories to train
stadium and air stations.
1. ESS decoding and digital servo.
2. Plays CD and MP3 encoded discs.
2. GENERAL DESCRIPTION
Note : An all-pole mains switch with a contact separation of at least 3 mm in each pole shall
be incorporated in the electrical installation of the building.
3. FEATURES
4. NOMENCLATURE AND FUNCTIONS
a. Front panel
1. POWER : Power indicator.
2. POWER SWITCH : On top of the opening power, press the end, power shut down.
3. GIVE ON
4. CD SCREEN : Display the working state of CD.
5. OPEN / CLOSE
6. PLAY / PAUSE
7. STOP / RETURN : Band search button (CD)
8. PREVIOUS : Previous band search button (CD)
9. NEXT : Next band search button (CD)
10. AUDIO OUT
11. ~230V/50Hz AC POWER INPUT
b. Rear panel
6
1. Press «power» switch on power supply.
2. Button function.
3. Dish placements tray up.
4. Press key «open/close» tray close start read.
5. Play diskette :
PLAY / PAUSE
STOP / RETURN
PREVIOUS
NEXT
6. CD diskette play
• Placement CD diskette read back enter rstly catalog choice menus and play rstly song
use previous and next key can elect demand song.
• Play course press key stop, menu backtrack catalog choice menus using previous and
next key choose demand song press key play come into homologous catalog choice
menus, a new press key play, carry out like 1 of play function.
Rear panel connections.
Power requirements ~230V / 50 Hz
Power consumption 30W
Dimensions 484 x 352 x 88 mm
Weight 3.8 kg
5. CD OPERATION
6. APPLICATIONS
7. SPECIFICATIONS
7
Keep the unit’s all sides over 10 cm away the
objects that may obstruct air ow to prevent
the unit’s internal temperature rise.
Unit : mm
8. DIMENSIONAL DIAGRAM
Linear Technologie • 11 rue du Puits Rochefort • 42 100 Saint-Etienne
Tél: +33 (0)4 77 81 49 49 • Fax: +33 (0)4 77 81 49 40 • www.lineartech.fr
Table of contents
