Linksys WRTU54G-TM User manual

Model No.
Broadband Router
Wireless-G
WRTU54G-TM
User Guide
WIRELESS
GHz
2.4
802.11g
with 2 Phone Ports

Wireless-G Broadband Router with 2 Phone Ports
Copyright and Trademarks
Specifications are subject to change without notice. Linksys, Cisco and the Cisco Logo are registered trademarks
or trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2008
Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered
trademarks of their respective holders.
How to Use This User Guide
This User Guide has been designed to make understanding networking with the Wireless-G Broadband Router
easier than ever. Look for the following items when reading this User Guide:
In addition to these symbols, there are definitions for technical terms that are presented like this:
Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like
this:
Figure numbers and descriptions can also be found in the “List of Figures” section in the “Table of Contents”.
This exclamation point means there is a caution or
warning and is something that could damage your
property or the Wireless-G Broadband Router.
This checkmark means there is a note of interest and
is something you should pay special attention to
while using the Wireless-G Broadband Router.
This question mark provides you with a reminder
about something you might need to do while using
the Wireless-G Broadband Router.
word: definition.
Figure 0-1: Sample Figure Description
WRTU54G-TM-UG-81009-B-BW-DF-JL
WARNING: This product contains chemicals, including lead, known
to the State of California to cause cancer, and birth defects or other
reproductive harm. Wash hands after handling.

Wireless-G Broadband Router with 2 Phone Ports
TableofContents
Chapter 1: Introduction 1
Welcome 1
What’s in this User Guide? 2
Chapter 2: Planning Your Wireless Network 4
Network Topology 4
Ad-Hoc versus Infrastructure Mode 4
Network Layout 4
Chapter 3: Getting to Know the Wireless-G Broadband Router 6
The Back Panel 6
The Front Panel 7
Chapter 4: Connecting the Wireless-G Broadband Router with 2 Phone Ports 8
Overview 8
Hardware Installation for Connection to Your Broadband Modem 8
Hardware Installation for Connection to An Existing Router 10
Placement Options 12
SIM Card Installation 13
Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports 14
Overview 14
The Setup Tab - Basic Setup 15
The Setup Tab - DDNS 19
The Setup Tab - MAC Address Clone 20
The Setup Tab - Advanced Routing 21
The Wireless Tab - Basic Wireless Settings 22
The Wireless Tab - Wireless Security 23
The Wireless Tab - Wireless MAC Filter 26
The Wireless Tab - Advanced Wireless Settings 27
The Security Tab - Firewall 29
The Security Tab - VPN Passthrough 29
The Access Restrictions Tab - Internet Access 30
The Applications and Gaming Tab - Port Range Forward 32
The Applications & Gaming Tab - Port Triggering 33
The Applications and Gaming Tab - DMZ 34

Wireless-G Broadband Router with 2 Phone Ports
The Applications and Gaming Tab - QoS 34
The Administration Tab - Management 36
The Administration Tab - Log 36
The Administration Tab - Diagnostics 37
The Administration Tab - Factory Defaults 38
The Administration Tab - Firmware Upgrade 38
The Administration Tab - Config Management 38
The Status Tab - Router 39
The Status Tab - Local Network 40
The Status Tab - Wireless 41
The Status Tab - Voice 42
Appendix A: Troubleshooting 43
Common Problems and Solutions 43
Frequently Asked Questions 50
Appendix B: Wireless Security 57
Security Precautions 57
Security Threats Facing Wireless Networks 57
Appendix C: Upgrading Firmware 60
Appendix D: Windows Help 61
Appendix E: Finding the MAC Address and IP Address for Your
Ethernet Adapter 62
Windows 2000 or XP Instructions 62
Windows Vista Instructions 62
For the Router’s Web-based Utility 63
Appendix F: Glossary 64
Appendix G: Specifications 71
Appendix H: Warranty Information 73
Appendix I: Regulatory Information 74
Appendix J: Software License Agreement 81
Software in Linksys Products 81
Schedule 1 - Linksys Software License Agreement 81
Schedule 2 84
Schedule 3 89
Schedule 4 97
Appendix K: Contact Information 100

Wireless-G Broadband Router with 2 Phone Ports
ListofFigures
Figure 3-1: The Router’s Back Panel 6
Figure 3-2: The Router’s Front Panel 7
Figure 4-1: Connecting Your Internet Connection 8
Figure 4-2: Connecting Your Network Devices 9
Figure 4-3: Connecting the Power 9
Figure 4-4: Connecting the Phone 9
Figure 4-5: Diagram for Connection to Another Router 10
Figure 4-6: Connecting to Another Router 10
Figure 4-7: Connecting Your Network Devices 10
Figure 4-8: Connecting the Power 11
Figure 4-9: Connecting the Phone 11
Figure 4-10: Measurement between Wall-Mount Slots 12
Figure 4-11: Slide Down the SIM Card Cover 13
Figure 4-12: Slide and Lift SIM Card Holder and Insert SIM Card 13
Figure 4-13: Fold Down the SIM Card Holder and Slide into Place 13
Figure 5-1: Password Screen 14
Figure 5-2: Setup Tab - Basic Setup 15
Figure 5-3: DHCP Connection Type 15
Figure 5-4: Static IP Connection Type 15
Figure 5-5: PPPoE Connection Type 16
Figure 5-6: PPTP Connection Type 16
Figure 5-7: L2TP Connection Type 17
Figure 5-8: Optional Settings 17
Figure 5-9: Router IP 18
Figure 5-10: Network Address Server Settings 18
Figure 5-11: Time Setting 18
Figure 5-12: Setup Tab - DDNS 19
Figure 5-13: Setup Tab - DDNS 19
Figure 5-14: Setup Tab - MAC Address Clone 20
Figure 5-15: Setup Tab - Advanced Routing (Router) 21
Figure 5-16: Setup Tab - Advanced Routing (Bridge) 21

Wireless-G Broadband Router with 2 Phone Ports
Figure 5-17: Wireless Tab - Basic Wireless Settings 22
Figure 5-18: Wireless Tab - Wireless Security (WPA Personal) 23
Figure 5-19: Wireless Tab - Wireless Security (WPA Enterprise) 23
Figure 5-20: Wireless Tab - Wireless Security (WPA2 Personal) 24
Figure 5-21: Wireless Tab - Wireless Security (WPA2 Enterprise) 24
Figure 5-22: Wireless Tab - Wireless Security (RADIUS) 25
Figure 5-23: Wireless Tab - Wireless Security (WEP) 25
Figure 5-24: Wireless Tab - Wireless MAC Filter 26
Figure 5-25: MAC Address Filter List 26
Figure 5-26: Wireless Tab - Advanced Wireless Settings 27
Figure 5-27: Security Tab - Firewall 29
Figure 5-28: Security Tab - VPN Passthrough 29
Figure 5-29: Access Restrictions Tab - Internet Access 30
Figure 5-30: Internet Policy Summary 30
Figure 5-31: List of PCs 30
Figure 5-32: Port Services 31
Figure 5-33: Applications and Gaming Tab - Port Range Forward 32
Figure 5-34: Applications and Gaming Tab - Port Triggering 33
Figure 5-35: Applications and Gaming Tab - DMZ 34
Figure 5-36: Applications and Gaming Tab - QOS 34
Figure 5-37: Administration Tab - Management 36
Figure 5-38: Administration Tab - Log 36
Figure 5-39: Administration Tab - Diagnostics 37
Figure 5-40: The Ping Test 37
Figure 5-41: The Traceroute Test 37
Figure 5-42: Administration Tab - Factory Defaults 38
Figure 5-43: Administration Tab - Firmware Upgrade 38
Figure 5-44: Administration Tab - Config Management 38
Figure 5-45: Status Tab - Router 39
Figure 5-46: Status Tab - Local Network 40
Figure 5-47: DHCP Clients Table 40
Figure 5-48: Status Tab - Wireless 41
Figure 5-49: Status Tab - Voice 42
Figure 5-50: Status Tab - Voice - Call Log 42

Wireless-G Broadband Router with 2 Phone Ports
Figure 5-51: Status Tab - Voice - Error List 42
Figure C-1: Upgrade Firmware 60
Figure E-1: MAC Address/Physical Address 62
Figure E-2: MAC Address Filter List 62
Figure E-3: MAC Address Clone 63

1
Chapter 1: Introduction
Welcome
Wireless-G Broadband Router with 2 Phone Ports
Chapter1:Introduction
Welcome
Thank you for choosing the Linksys Wireless-G Broadband Router with 2 Phone Ports. The Wireless-G Broadband
Router with 2 Phone Ports will allow you to network wirelessly better than ever, sharing Internet access, files and
fun, easily and securely.
How does the Wireless-G Broadband Router with 2 Phone Ports do all of this? A router is a device that allows
access to an Internet connection over a network. With the Wireless-G Broadband Router with 2 Phone Ports, this
access can be shared over the four switched ports or via the wireless broadcast at up to 11Mbps for Wireless-B
or up to 54Mbps for Wireless-G.
Use the WPA standard to secure your wireless network while the whole network is protected through a Stateful
Packet Inspection (SPI) firewall and Network Address Translation (NAT) technology. Just run the Setup Wizard and
it will guide you through the steps to set up your network. You can also access the Router’s features through the
easy-to-use, browser-based utility.
But what does all of this mean?
Networks are useful tools for sharing computer resources. You can access one printer from different computers
and access data located on another computer's hard drive. Networks are even used for playing multiplayer video
games. So, networks are not only useful in homes and offices, they can also be fun.
PCs on a wired network create a LAN, or Local Area Network. They are connected with Ethernet cables, which is
why the network is called “wired”.
PCs equipped with wireless cards or adapters can communicate without cumbersome cables. By sharing the
same wireless settings, within their transmission radius, they form a wireless network. This is sometimes called
a WLAN, or Wireless Local Area Network. The Wireless-G Broadband Router with 2 Phone Ports bridges wireless
networks of both 802.11b and 802.11g standards and wired networks, allowing them to communicate with each
other.
With your networks all connected, wired, wireless, and the Internet, you can now share files and Internet
access—and even play games. All the while, the Wireless-G Broadband Router with 2 Phone Ports protects your
networks from unauthorized and unwelcome users.
Linksys recommends using the Setup CD-ROM for first-time installation of the Router. If you do not wish to run
the Setup Wizard on the Setup CD-ROM, then use the instructions in this Guide to help you connect the
lan (local area network): The computers and
networking products that make up the network in
your home or office.
nat (network address translation): NAT technology
translates IP addresses of a local area network to a
different IP address for the Internet.
wpa (wi-fi protected access): a wireless security
protocol using TKIP (Temporal Key Integrity Protocol)
encryption, which can be used in conjunction with a
RADIUS server.
spi (stateful packet inspection) firewall: a technology
that inspects incoming packets of information before
allowing them to enter the network.
firewall: Security measures that protect the
resources of a local network from intruders.
NOTE: The Setup Wizard is not compatible with
Mac®computers. Refer to Chapter 4: Connecting the
Wireless-G Broadband Router with 2 Phone Ports and
Chapter 5: Configuring the Wireless-G Broadband
Router with 2 Phone Ports.

2
Chapter 1: Introduction
What’s in this User Guide?
Wireless-G Broadband Router with 2 Phone Ports
Wireless-G Broadband Router with 2 Phone Ports, set it up, and configure it to bridge your different networks.
These instructions should be all you need to get the most out of the Wireless-G Broadband Router with 2 Phone
Ports.
What’s in this User Guide?
This user guide covers the steps for setting up and using the Wireless-G Broadband Router with 2 Phone Ports.
• Chapter 1: Introduction
This chapter describes the Router’s applications and this User Guide.
• Chapter 2: Planning Your Wireless Network
This chapter describes the basics of wireless networking.
• Chapter 3: Getting to Know the Wireless-G Broadband Router with 2 Phone Ports
This chapter describes the physical features of the Router.
• Chapter 4: Connecting the Wireless-G Broadband Router with 2 Phone Ports
This chapter instructs you on how to connect the Router to your network.
• Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports
This chapter explains how to use the Web-based Utility to configure the settings on the Wireless-G Broadband
Router with 2 Phone Ports.
• Appendix A: Troubleshooting
This appendix describes some problems and solutions, as well as frequently asked questions, regarding
installation and use of the Wireless-G Broadband Router with 2 Phone Ports.
• Appendix B: Wireless Security
This appendix explains the risks of wireless networking and some solutions to reduce the risks.
• Appendix C: Upgrading Firmware
This appendix instructs you on how to upgrade the firmware on the Router should you need to do so.
• Appendix D: Windows Help
This appendix describes how you can use Windows Help for instructions about networking, such as installing
the TCP/IP protocol.
• Appendix E: Finding the MAC Address and IP Address for your Ethernet Adapter.
This appendix describes how to find the MAC address for your computer’s Ethernet adapter so you can use
the MAC filtering and/or MAC address cloning feature of the Router.

3
Chapter 1: Introduction
What’s in this User Guide?
Wireless-G Broadband Router with 2 Phone Ports
• Appendix F: Glossary
This appendix gives a brief glossary of terms frequently used in networking.
• Appendix G: Specifications
This appendix provides the technical specifications for the Router.
• Appendix H: Warranty Information
This appendix supplies the warranty information for the Router.
• Appendix I: Regulatory Information
This appendix supplies the regulatory information regarding the Router.
• Appendix J: Contact Information
This appendix provides contact information for a variety of Linksys resources, including Technical Support.

4
Chapter 2: Planning Your Wireless Network
Network Topology
Wireless-G Broadband Router with 2 Phone Ports
Chapter2:PlanningYourWirelessNetwork
Network Topology
A wireless local area network (WLAN) is exactly like a regular local area network (LAN), except that each
computer in the WLAN uses a wireless device to connect to the network. Computers in a WLAN share the same
frequency channel and SSID, which is an identification name shared by the wireless devices belonging to the
same wireless network.
Ad-Hoc versus Infrastructure Mode
Unlike wired networks, wireless networks have two different modes in which they may be set up: infrastructure
and ad-hoc. An infrastructure configuration is a WLAN and wired LAN communicating to each other through an
access point. An ad-hoc configuration is wireless-equipped computers communicating directly with each other.
Choosing between these two modes depends on whether or not the wireless network needs to share data or
peripherals with a wired network or not.
If the computers on the wireless network need to be accessible by a wired network or need to share a peripheral,
such as a printer, with the wired network computers, the wireless network should be set up in Infrastructure
mode. The basis of Infrastructure mode centers around a wireless router or an access point, such as the
Wireless-G Broadband Router, which serves as the main point of communications in a wireless network. The
Router transmits data to PCs equipped with wireless network adapters, which can roam within a certain radial
range of the Router. You can arrange the Router and multiple access points to work in succession to extend the
roaming range, and you can set up your wireless network to communicate with your Ethernet hardware as well.
If the wireless network is relatively small and needs to share resources only with the other computers on the
wireless network, then the Ad-Hoc mode can be used. Ad-Hoc mode allows computers equipped with wireless
transmitters and receivers to communicate directly with each other, eliminating the need for a wireless router or
access point. The drawback of this mode is that in Ad-Hoc mode, wireless-equipped computers are not able to
communicate with computers on a wired network. And, of course, communication between the wireless-
equipped computers is limited by the distance and interference directly between them.
Network Layout
The Wireless-G Broadband Router has been specifically designed for use with both your 802.11b and 802.11g
products. Now, products using these standards can communicate with each other.
infrastructure: a wireless network that is bridged
to a wired network via an access point.
ssid (service set identifier): your wireless network’s name.
ad-hoc: a group of wireless devices
communicating directly to each other (peer-to-
peer) without the use of an access point.

5
Chapter 2: Planning Your Wireless Network
Network Layout
Wireless-G Broadband Router with 2 Phone Ports
The Wireless-G Broadband Router is compatible with all 802.11b and 802.11g adapters, such as the Notebook
Adapters (WPC54G, WPC11) for your laptop computers, PCI Adapter (WMP54G, WMP11) for your desktop PC, and
USB Adapter (WUSB54G, WUSB11) when you want to enjoy USB connectivity. The Broadband Router will also
communicate with the Wireless PrintServer (WPS54G) and Wireless Ethernet Bridges (WET54G, WET11).
When you wish to connect your wireless network with your wired network, you can use the Wireless-G
Broadband Router’s four LAN ports. To add more ports, any of the Wireless-G Broadband Router's LAN ports can
be connected to any of Linksys's switches (such as the SD205 or SD208).
With these, and many other, Linksys products, your networking options are limitless. Go to the Linksys website at
www.linksys.com for more information about products that work with the Wireless-G Broadband Router.

6
Chapter 3: Getting to Know the Wireless-G Broadband Router
The Back Panel
Wireless-G Broadband Router with 2 Phone Ports
Chapter3:GettingtoKnowtheWireless-GBroadband
Router
The Back Panel
The Router's ports, where the cables are connected, are located on the back panel.
Internet The Internet port is where you will connect your broadband Internet connection.
Ethernet 1-4 These ports (1-4) connect the Router to your networked PCs and other Ethernet network
devices.
Phone1 /Phone2 You can connect a phone in each of these ports.
Reset Button There are two ways to reset the Router's factory defaults. Either press the Reset Button, for
approximately five seconds, or restore the defaults from the Administration tab - Factory
Defaults in the Router's Web-based Utility.
Power The Power port is where you will connect the power adapter.
IMPORTANT: Resetting the Router will erase
all of your settings (Internet connection,
wireless security, and other settings) and
replace them with the factory defaults. Do not
reset the Router if you want to retain these
settings.
Figure 3-1: The Router’s Back Panel

7
Chapter 3: Getting to Know the Wireless-G Broadband Router
The Front Panel
Wireless-G Broadband Router with 2 Phone Ports
The Front Panel
The Router’s LEDs are located on the front panel.
Power Green. The Power LED lights up and will stay on while the Router is powered on. When the
Router goes through its self-diagnostic mode during every boot-up, this LED will flash. When
the diagnostic is complete, the LED will be solidly lit.
Ethernet 1-4 Green. These numbered LEDs, corresponding with the numbered ports on the Router’s back
panel, serve two purposes. If the LED is continuously lit, the Router is successfully connected
to a device through that port. A flashing LED indicates network activity over that port.
Wireless Green. The WLAN LED lights up whenever there is a successful wireless connection. If the LED
is flashing, the Router is actively sending or receiving data over the network.
Phone1/Phone2 Blue. This LED lights up blue when a SIM card is correctly installed and registered. It will blink
when you have new voicemail.
Internet Green. The Internet LED lights up when there is a connection made through the Internet port.
The LED flashes when there is traffic.
Pairing Green. The LED lights up green when wireless security is enabled. When the Pairing button is
pushed, the Pairing LED flashes amber, then when the pairing is done, the LED lights up green.
Figure 3-2: The Router’s Front Panel

8
Chapter 4: Connecting the Wireless-G Broadband Router with 2 Phone Ports
Overview
Wireless-G Broadband Router with 2 Phone Ports
Chapter4:ConnectingtheWireless-GBroadbandRouter
with2PhonePorts
Overview
This chapter includes two sets of connection instructions. If the Wireless-G Broadband Router with 2 Phone Ports
will be the only router in your network, follow the instructions in “Hardware Installation for Connection to Your
Broadband Modem.” If you want to install the Wireless-G Broadband Router with 2 Phone Ports behind an existing
router in your network, then follow the instructions in “Hardware Installation for Connection to an existing
Router.” Also included are Placement instructions, and SIM Card Installation instructions.
Hardware Installation for Connection to Your Broadband Modem
1. Power down your network devices.
2. Locate an optimum location for the Router. The best place for the Router is usually at the center of your
wireless network, with line of sight to all of your mobile stations.
3. Fix the direction of the antennas. Try to place the Router in a position that will best cover your wireless
network. Normally, the higher you place the antenna, the better the performance will be.
4. Connect a standard Ethernet network cable to the Router’s Internet port. Then, connect the other end of the
Ethernet cable to your cable or DSL broadband modem.
Figure 4-1: Connecting Your Internet Connection

9
Chapter 4: Connecting the Wireless-G Broadband Router with 2 Phone Ports
Hardware Installation for Connection to Your Broadband Modem
Wireless-G Broadband Router with 2 Phone Ports
5. Connect your network PCs or Ethernet devices to the Router’s numbered ports using standard Ethernet
network cabling.
6. Connect the AC power adapter to the Router's Power port and the other end into an electrical outlet. Only use
the power adapter supplied with the Router. Use of a different adapter may damage the product.
7. Connect a standard telephone to the Router’s Phone1 port. If you have a second phone, connect the telephone to the
Router’s Phone2 port.
Figure 4-2: Connecting Your Network Devices
Figure 4-3: Connecting the Power
IMPORTANT: Make sure you use the power
adapter that is supplied with the Router. Use of a
different power adapter could damage the Router.
Figure 4-4: Connecting the Phone
IMPORTANT: Do not connect the Phone port to a
telephone wall jack. Make sure you only connect a
telephone to the Phone port. Otherwise, the Router or the
telephone wiring in your home or office may be damaged.

10
Chapter 4: Connecting the Wireless-G Broadband Router with 2 Phone Ports
Hardware Installation for Connection to An Existing Router
Wireless-G Broadband Router with 2 Phone Ports
Now that the hardware installation is complete, proceed to “Chapter 5: Configuring the Wireless-G
Broadband Router with 2 Phone Ports,” for directions on how to configure the Router.
Hardware Installation for Connection to An Existing Router
Your existing Router may have the same default IP address (192.168.0.1) as your new T-Mobile router. If this is
the case, the T-Mobile router’s IP address will change to 192.168.24.1.
1. Power down your network devices. Now you will begin the hardware installation of router.
2. Locate an optimum location for the Router. The best place for the router is usually at the center of your
wireless network, with line of sight to all of your mobile stations.
3. Fix the direction of the antennas. Try to place the Router in a position that will best cover your wireless
network. Normally, the higher you place the antenna, the better the performance will be.
4. Connect a standard Ethernet network cable to the T-Mobile router’s Internet port. Then, connect the other end
of the Ethernet cable to one of the numbered Ethernet ports on your existing router.
5. Decide which network computers or Ethernet devices you want to connect to the Router.
Figure 4-5: Diagram for Connection to Another Router
Internet
Broadband
Modem
Router
Wireless-G
Broadband
Router
with 2 Phone
Ports
Figure 4-6: Connecting to Another Router
Multiple PCs
Figure 4-7: Connecting Your Network Devices

11
Chapter 4: Connecting the Wireless-G Broadband Router with 2 Phone Ports
Hardware Installation for Connection to An Existing Router
Wireless-G Broadband Router with 2 Phone Ports
6. Disconnect the selected computers or devices from the old router, and then connect them to the T-Mobile
router’s numbered ports using standard Ethernet network cabling.
7. Connect the AC power adapter to the T-Mobile router's power port and the other end into an electrical outlet.
Only use the power adapter supplied with the T-Mobile router. Use of a different adapter may result in product
damage.
8. Connect a standard telephone to the Router’s Phone1 port. If you have a second phone, connect the telephone to the
Router’s Phone2 port.
Now that the hardware installation is complete, proceed to “Chapter 5: Configuring the Wireless-G
Broadband Router with 2 Phone Ports,” for directions on how to configure the Router.
IMPORTANT: Make sure you use the power
adapter that is supplied with the Router. Use of a
different power adapter could damage the Router.
Figure 4-8: Connecting the Power
Figure 4-9: Connecting the Phone
IMPORTANT: Do not connect the Phone port to a
telephone wall jack. Make sure you only connect a
telephone to the Phone port. Otherwise, the Router or the
telephone wiring in your home or office may be damaged.

12
Chapter 4: Connecting the Wireless-G Broadband Router with 2 Phone Ports
Placement Options
Wireless-G Broadband Router with 2 Phone Ports
Placement Options
There are three ways to place the Router. The first way is to place it horizontally on a surface, so it sits on its four rubber feet.
Another option is to install the stand onto the bottom of the Router, so the Router is in an upright position. Make sure to place
the Router’s bottom edge of the Cisco logo in between the stand’s prongs until tight. The third way is to mount it on a wall.This
option uses the Router’s four wall-mount slots on its bottom panel. The distance between two adjacent slots is 60 mm (2.36
inches).
To use the wall-mount option, follow these instructions:
1. Make sure you have four screws that are size #4—this indicates a diameter measurement of 2.845 mm (0.112 inches).
2. Determine where you want to mount the Router.
3. Drill four holes into the wall. Make sure adjacent holes are 60 mm (2.36 inches) apart.
4. Insert a screw into each hole, and leave 5 mm (0.2 inches) of its head exposed.
5. Maneuver the Router so the wall-mount slots line up with the four screws.
6. Place the wall-mount slots over the screws and slide the Router down until the screws fit snugly into the wall-mount
slots.
Proceed to “Chapter 5: Configuring the Wireless-G Broadband Router with 2 Phone Ports” for directions
on how to configure the Router.
60 mm
(2.36 inches)
Figure 4-10: Measurement between Wall-
Mount Slots

13
Chapter 4: Connecting the Wireless-G Broadband Router with 2 Phone Ports
SIM Card Installation
Wireless-G Broadband Router with 2 Phone Ports
SIM Card Installation
Two SIM cards are required for a 2-line configuration.
To install a SIM card, follow these steps:
1. Slide the SIM card cover down, then lift off.
2. Gently slide up the SIM card holder. Then from the bottom side, carefully lift up the SIM card holder. Do not lift
the holder until it is correctly in place or it could break.
3. Position the SIM card with the gold metal side up and towards the card slot opening. Carefully insert the SIM
card into the slot until it lines up with the bottom edge of the top piece of the holder and before it hits the
bottom piece of the holder or the SIM card or holder could break.
4. Fold down the SIM card holder and slide down into place.
5. Replace the SIM card cover. You might need to push it hard to lock it in place.
Figure 4-11: Slide Down the SIM Card Cover
Figure 4-12: Slide and Lift SIM Card Holder and Insert SIM Card
Slide up SIM card holder this
direction
Slide SIM in only this far
and not to the bottom
1
2
3
Bottom Side
Bottom Piece
of Holder
Top Piece of
Holder
Figure 4-13: Fold Down the SIM Card Holder and Slide into
Place
4