LINOVISION POE-Extender02 GP User manual

1
2
2 Port Gigabit 802.3af/at/bt PoE Extender
User Manual
V2.0
Gigabit 802.3af/at/bt PoE Ethernet Repeater, which uses advanced network cable drive and power supply technology
to extend 1000Mbps Ethernet signal to 100 meters, greatly extending the transmission distance and providing 50~57V
PoE power at the same time, the PoE output power can be up to 50W/80W. IP67-rated, industrial grade enclosure can
meet requirement of harsh environment, working temperature can be up to -40~75℃. It is widely used in security
surveillance and network projects.
Features
Including two models:
--provide 2*10/100/1000Mbps PoE Ethernet ports:
One 802.3af/at/bt PoE input port, one 802.3af/at/bt PoE output port.
--provide 3*10/100/1000Mbps PoE Ethernet ports:
One 802.3af/at/bt PoE input port, two 802.3af/at/bt PoE output ports.
Both models can meet the requirements of 802.3bt PoE powered devices such as PTZ speed dome camera,
digital display.
Use advanced network cable drive technology, the transmission distance can be up to 100m.
PoE power supply is compatible with End-span and Mid-span.
Meet standards of IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.3ab 1000Base-T.
Excellent circuit isolation protection, effectively improve product's lightning protection, ESD and anti-interference
ability.
Easy to install, special designed waterproof joint allows RJ-45 pass through directly, no need for RJ-45 assembly.
Plug and play, no setting required.
Notice
It is recommended to use the standard Cat6 network cable (or better) to reach the optimal transmission distance.
────────────────────────────◀◀◀2 Port Gigabit PoE Extender
Board Diagram
1 Output
2 Outputs
Installation Steps
Please check the following items before installation, if missing, please contact the dealer.
2 Port PoE Extender 1 pcs
Waterproof Joint 2pcs(1 output port repeater)/ 3pcs (2 output ports repeater)
User Manual 1 pcs
Installation steps:
1 ) Please turn off the signal source and the device's power, installation with power on may damage the device.
2) Check if the network cable and other transmission line that will be used is occupied by other device.
3) Use a network cable to connect PoE IN port of the repeater with PoE adapter or switch.
4) Use a network cable to connect PoE powered device with PoE OUT port of repeater.
5) Check if the installation is correct and device is good, make sure all the connection is reliable and power up the
system.
Notice
The PoE IN and PoE OUT Ports must be correctly connected, or the repeater will not work.

2 Port Gigabit PoE Extender ▶▶▶────────────────────────────
────────────────────────────◀◀◀2 Port Gigabit PoE Extender
3
4
Hardware Specifications
Items
2 Port Gigabit PoE Extender
with 1 PoE output port
2 Port Gigabit PoE Extender
with 2 PoE output ports
60W
90W
60W
90W
PoE Input Port
10/100/1000Base-TX RJ-45,
IEEE 802.3bt PoE Input
Input Power 50~57V DC,
Max 60W
10/100/1000Base-TX RJ-45,
IEEE 802.3bt PoE Input
Input Power 50~57V DC,
Max 90W
10/100/1000Base-TX RJ-45,
IEEE 802.3bt PoE Input
Input Power 50~57V DC,
Max 60W
10/100/1000Base-TX RJ-45,
IEEE 802.3bt PoE Input
Input Power 50~57V DC,
Max 90W
PoE Output Port
1*10/100/1000Base-TX RJ-45,
IEEE 802.3bt/at PoE Output
Output power:
Max 58W in total,
58W@ 101m, 50W@ 200m
1*10/100/1000Base-TX RJ-45,
IEEE 802.3bt/at PoE Output
Output Power:
Max 81W in total,
73.7W@ 101m, 59W@ 200m
2*10/100/1000Base-TX RJ-45,
IEEE 802.3bt/at PoE Output
Output Power:
Max 58W in total,
58W@ 101m, 50W@ 200m
2*10/100/1000Base-TX RJ-45,
IEEE 802.3bt/at PoE Output
Output Power:
Max 81W in total,
73.7W@ 101m, 59W@ 200m
Cascade
Connection
Max: Support 3 grade
Max: Support 3 grade
Max: Support 3 grade
Max: Support 3 grade
PoE Power
Supply Type
Mid-span and End-span
PoE Pin
Assignment
1/2(+), 3/6(-), 4/5(+), 7/8(-)
PoE Standard
IEEE 802.3af/at/bt
Standards
IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
Forwarding
Modes
Store and Forward
Transmission
Distance
100m
MAC Table
8k
Switching
Capacity
4Gbps
6Gbps
Packet
Forwarding Rate
2.98Mpps
4.46Mpps
Flow Control
IEEE 802.3x pause frame for full duplex, Back pressure for half duplex
Jumbo Frame
10kB
ESD Protection
6kV 1a Contact Discharge Level 3, 8kV 1b Air Discharge Level 3, Standard: IEC61000-4-2
Surge Immunity
6kV, Standard: IEC6000-4-5
Protection Level
IP67
Operating
Temperature
-40℃~75℃
Storage
Temperature
-40℃~85℃
Operating
Humidity
0~95% (No condensation)
Dimensions
(W*D*H)
193mm*75mm*38mm
Gross Weight
558g
576g
Net Weight
423g
467g
Material
Aluminum
Certifications
CE, FCC, RoHS
After-service (Please cut the warranty card along the dotted line)
Version,V2.0, updated 2020.7.10.
The information in this document is subject to change without notice.
Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.