Lite-Puter EDX-607 User manual

ISO 9001 CERTIFIED www.liteputer.com.tw
Lite-Puter
EDX-607E [EUM-A]
EDX-607
6 Channels Lighting Controller
User Manual
Lite Puter Enterprise Co., Ltd.
www.liteputer.com.tw
[e-mail]

ISO 9001 CERTIFIED www.liteputer.com.tw
Lite-Puter
EDX-607E [EUM-A]
Index
Chapter 1. Introduction ....................................................................................................... 1
1-1 Feature .................................................................................................................1
1-2 Specification..........................................................................................................1
1-3 Wiring Diagram .....................................................................................................2
1-4 Installation.............................................................................................................2
1-5 System Wiring Diagram ........................................................................................5
1-6 Panel introduction .................................................................................................6
Chapter 2. Operation Description ..................................................................................... 7
2-1 Function Introducing .............................................................................................7
2-2 Initialization ...........................................................................................................8
2-3 DMX Start Channel Setting ...................................................................................8
2-4 Zone Setting .........................................................................................................8
2-5 Partition Setting.....................................................................................................9
2-6 ID_NO Setting.....................................................................................................12
2-7 Fade Time Setting...............................................................................................13
2-8 System Clock Setting..........................................................................................13
2-9 Timer ON/OFF ....................................................................................................14
2-10 Dimming /Switch (Non-dimming) Mode Setting ................................................. 14
2-11 Display System Temperature.............................................................................15
2-12 Display Current Load ........................................................................................15
2-13 Set Timer ..........................................................................................................15
1. Add Record ............................................................................................15
2. Edit Record ............................................................................................16
3. Delete Record ........................................................................................16
2-14 Scene Setting....................................................................................................16
2-15 Scene Recall.....................................................................................................17
2-16 Memory & Button Lock/Unlock Function............................................................ 17
2-17 Adjust and View Dimming Value........................................................................17
2-18 Panel LED on/off Setting...................................................................................18
2-19 Dimming Curve Setting .....................................................................................18
2-20 Enable/Disable Partition Function .....................................................................19
2-21 Checking Software Version ...............................................................................19
2.22 Enable/Disable IR Remote Control....................................................................19
2-23 Enable/Disable SC5/6 Overlap Scene Function ................................................19
2.24 Clock Synchronization.......................................................................................20
Safety Precaution ................................................................................................................. 21
Guarantee.............................................................................................................................. 22

ISO 9001 CERTIFIED www.liteputer.com.tw
1Lite-Puter
EDX-607E [EUM-A]
Chapter 1. Introduction
1-1 Feature
6 channels, total current 16A. The maximum load capacity of each channel can be up
to 4 A.
The master panel can store 12 groups of scenes; each scene can store 12 channels,
display 12 channels dimming value and transmit 12 channels DMX data.
Equipped with IR remote controller, it can recall 6 scenes, change any channel
dimming level and edit 6 scenes directly. You can also view current zone number and
set fade in/fade out time by IR remote controller.
C1, C2, C3 liner dimming curve.
Fade in/fade out time setting.
Timer control can execute preset lighting scenes periodically and automatically
(24hours).
Each channel can be set as dimming or non-dimming.
Display system temperature and detect temperature automatically. When the internal
temperature is over 62°C, it will alert and limit the output to 50%. Over 65°C it will stop
output automatically.
When the total current over 25A, EDX-607 will stop outputting and press

OFF

button to reset; when the total current over 20A, EDX-607 will limit the output till the
total current lower than 16A and press any scene button to reset.
Can be controlled and monitored by PC through Lite-Puter’s Ethernet interface
(DP-E450 ,etc).
Can be connected to ECP series control panels.
 Button lock/unlock.
1-2 Specification
Power Input

AC 277V
Output

4A per channel, Total Max. 16A. Resistant load only.
Protocol: DMX-512/ RS-485
Dimension: 212 (W) x 118 (H) x 60 (D)mm
Weight: 0.8 KG

ISO 9001 CERTIFIED www.liteputer.com.tw
2 Lite-Puter
EDX-607E [EUM-A]
1-3 Wiring Diagram
1-4 Installation

ISO 9001 CERTIFIED www.liteputer.com.tw
3 Lite-Puter
EDX-607E [EUM-A]

ISO 9001 CERTIFIED www.liteputer.com.tw
4 Lite-Puter
EDX-607E [EUM-A]

ISO 9001 CERTIFIED www.liteputer.com.tw
5 Lite-Puter
EDX-607E [EUM-A]
1-5 System Wiring Diagram

ISO 9001 CERTIFIED www.liteputer.com.tw
6 Lite-Puter
EDX-607E [EUM-A]
1-6 Panel introduction
1
Scene buttons
2
IR receiver
3
LED
4
Channel dimming value display or other function meaning
5
Function buttons
6
CH1- CH12 dimming value UP
7
CH1- CH12 dimming value DOWN
1
2
5
7
4
3
6

ISO 9001 CERTIFIED www.liteputer.com.tw
Lite-Puter
EDX-607E [EUM-A]
7
Chapter 2. Operation Description
2-1 Function Introducing
Long holdFCNfor 3 seconds and then pressFCNto select a function from the
following list:
Display Combined Button Function
FCN+CH1_UPSet ID No.
FCN+CH2_UPSet Zone No.
FCN+CH3_UPSet DMX start channel
address
FCN+CH4_UPSet scene FADER TIME
FCN+CH5_UPModify system time
FCN+CH6_UPTimer on/off
FCN+CH1_DOWNChannel
dimming/switch(non-dimming)
mode setting
FCN+CH2_DOWNView and set the timer
FCN+CH3_DOWNDisplay system temperature
FCN+CH4_DOWNDisplay the load current
FCN+CH5_DOWNDisplay the panel LED on /off
FCN+CH6_DOWNSelect dimming curve
Partition setting
Partition function on/off

ISO 9001 CERTIFIED www.liteputer.com.tw
Lite-Puter
EDX-607E [EUM-A]
8
IR remote control on/off
SC5/SC6 overlap scene
function switch
Software version
Clock Synchronization
P.S: There are 2 ways to enter function menu.
One is long holdFCNfor 3 seconds, then pressFCNto select functions. The other
is using combined buttons to select certain function then pressFCNto enter the
setting.
After setting, pressENTERto store. Press any scene buttons to exit function setting
without change. The system will exit the setting mode after 60 seconds idling.
2-2 Initialization
Long holdENTER+SHIFT+OFFat the same time for 3 seconds to initialize
the system.
2-3 DMX Start Channel Setting
STEP-1PressFCN+CH3_UPat the same time or long holdFCNfor 3 seconds
to enter function menu and then pressFCNtwice to select function , the
screen will display its DMX start channel address .
STEP-2Press ▲ or ▼ , DMX ADR (DMX address) will increase or decrease 10
addresses at one time. Press

or

, DMX ADR will increase or
decrease 1 address at one time.
STEP-3After setting, pressENTERto save and exit.
2-4 Zone Setting
Zone definition: User must set the control zone code of EDX-607 before using. This
code has two parts. The first part is zone number and the second is starting channel
address.
The standard DMX console can output 512 channels, while EDX-607 must select 12
continuous channels from these 512 channels. The first channel’s address of the 12
continuous channels is EDX-607’s DMX start channel address.

ISO 9001 CERTIFIED www.liteputer.com.tw
Lite-Puter
EDX-607E [EUM-A]
9
STEP-1PressFCN+CH2_UPat the same time or long holdFCNfor 3 seconds
to enter function menu and then pressFCNonce to select function ,the screen will
display the zone code .
STEP-2Press ▲ or ▼ to adjust the value; press

or 

to select the editing
items.
STEP-3PressENTERto save and exit.
Example
If zone number is 1 and the start channel is 1.To set zone as 3 and set start channel
as 2. The steps are as follows.
1. PressFCN+CH2_UPat the same time or long holdFCNfor 3 seconds to
enter function menu and then pressFCNonce to select function. The screen will
display, (The two digits on the right side are blinking.)
2. Pressonce, the two digits on the left side are blinking, it will display,
3.Press
▲ twice, it will display,
4. Press

once, The two digits on the right side are blinking, it will display,
5. Press
▲ once, it will display,
6. PressENTERto save and exit.
2-5 Partition Setting
This function is to set partition of each channel.
STEP-1 Long holdFCNfor 3 seconds to enter function menu and then pressFCN
12 times until the screen shows .
STEP-2 Press

or

to select partition no. and pressCH1- CH12 UPto select
channels to partition; pressCH1- CH12 DOWNto cancel channels out of partition.
STEP-3 PressENTERto save and exit.

ISO 9001 CERTIFIED www.liteputer.com.tw
Lite-Puter
EDX-607E [EUM-A]
10
Example: To set channel 1 to partition 2, channel 10 to partition 3 and other channels
to partition 1 (default). The steps are as follows.
1. Enter . The LED bars of channel 1 ~ 6 show all of them are in partition 1.
2. PressSto check channel 7 ~ 12, the LED bar of each channel shows all of them
belong to partition 1.

3. PressSshift to channel 1 ~ 6, press

once shift to partition 2.
6

ISO 9001 CERTIFIED www.liteputer.com.tw
Lite-Puter
EDX-607E [EUM-A]
11

4. PressCH1_UPto set channel 1 to partition 2, the LED bar shows that channel 1
is in partition 2 now.

5. Press

once to shift to partition 3.
&+B83

ISO 9001 CERTIFIED www.liteputer.com.tw
Lite-Puter
EDX-607E [EUM-A]
12
6. PressSshift to channel 7 ~ 12.
7. PressCH10_UPto set channel 10 to partition 3.
8. PressENTERto save and exit.
2-6 ID_NO Setting
STEP-1Long holdFCNfor 3 seconds or pressFCN+CH1_UPat the same
time, the screen will display its ID number.
Each EDX Series device has its ID number (default value: 001). If more
than one EDX devices are connected together, each of them has to be set
ID number.
&+B83

ISO 9001 CERTIFIED www.liteputer.com.tw
Lite-Puter
EDX-607E [EUM-A]
13
STEP-2Press ▲ or ▼ to select the ID number from 1 to 999.
STEP-3PressENTERto save and exit.
2-7 Fade Time Setting
STEP-1 Long holdFCNfor 3 seconds to enter function menu and then pressFCN
3 times to select the function or pressFCN+CH4_UPat the same time,
the screen will display the fade timeFdsetting as: .Then press
ENTERto enter setting.
STEP-2Press

or

to select and view the scenes FADE data. Press ▲ 
or ▼ to edit the fade time of the corresponding scene.
STEP-3 Press ENTERto save and exit.
Example
To set fade time of scene 2 from 1 second to 5 seconds. The steps are as
follows.
1. Long holdFCNfor 3 seconds to enter function menu and then pressFCN
3 times to select the function or pressFCN+CH4_UPat the same time,
the screen will display, .
2. Press ENTER, it will display,
3. Press

2 times to select scene 2 as .
4. Press
▲ 4 times or long hold ▲ to set fade time to 5 seconds as
5. PressENTERto save and exit.
2-8 System Clock Setting
STEP-1 Long holdFCNfor 3 seconds to enter function menu and then pressFCN
4 times to select the function or pressFCN+CH5_UPat the same time,
the screen will display the Clock Setting as .Then pressENTERto
modify the clock , it will display, .
STEP-2Press ▲ or ▼ to edit the time. Press

or press

to switch between
hour and minute.
STEP-3PressENTER to save and exit.
Example:
To set the clock to 10:24, the steps are as follows.

ISO 9001 CERTIFIED www.liteputer.com.tw
Lite-Puter
EDX-607E [EUM-A]
14
1.Long holdFCNfor 3 seconds to enter function menu and then pressFCN4 times
to select the function or pressFCN+CH5_UPat the same time, the screen will
display,
2.PressENTERto edit the clock, it will display,
3.Press

once shift to hour setting and then press
▲ 10 times or long hold ▲ 
to set hour as
4.Press

once, it will switch to minute setting as
5.Press
▲ 24 times or long hold ▲ to set minute as
6.PressENTERto save and exit.
2-9 Timer ON/OFF
STEP-1 Long holdFCNfor 3 seconds to enter function menu and then pressFCN
5 times to select the function or pressFCN+CH6_UPat the same time, the screen
will display timer status as .
STEP-2Press ▲ to turn on timer ;press ▼ to turn it off.
STEP-3PressENTERto save and exit.
2-10 Dimming /Switch (Non-dimming) Mode Setting
When dimming is unnecessary, users can set the channel to switch mode and control
it with either 100% on or totally off.
If any channel is set in switching mode, it will be turned on to 100%
immediately when the input is over 51% and turned off immediately when
the input is less than 20%. This function is avoid fixture blink.
STEP-1 Long holdFCNfor 3 seconds to enter function menu and then pressFCN
6 times to select the function or pressFCN+CH1_DOWNat the same time, the
screen will display,
STEP-2Press

or press

shift from channel 1 to channel 6. PressS
shift from channel 7 to channel 12. PressCH1- CH12 UPto set channel as switch
modeS; pressCH1- CH12 DOWNto set channel as dimming moded.
When you view each channel’s mode status, you can press
▲ to set it as switch
modeS, press
▼ to set it as dimming moded.
STEP-3PressENTER to save and exit.
Example:
Set channel 1 and 10 to switch mode. The steps are as follows.
1.Long holdFCNfor 3 seconds to enter function menu and then pressFCN6 times
to select the function or pressFCN+CH1_DOWNat the same time, the screen

ISO 9001 CERTIFIED www.liteputer.com.tw
Lite-Puter
EDX-607E [EUM-A]
15
will display , it means channel 1 is in dimming mode .
2.PressCH1_UPor press
▲ to set channel 1 as switch mode
3.Press Sshift to channel 7 to12, the screen will display
4.PressCH10_UPor press 

or

to select channel 10 and then press

▲ to set channel 10 as switch mode
5.PressENTERto save and exit.
2-11 Display system temperature
Long holdFCNfor 3 seconds to enter function menu and then pressFCN8 times
to select the function or pressFCN+CH3_DOWNat the same time, then the
screen will display the current temperature. PressENTERto exit.
Example: means the current temperature is 30°C.
When the internal temperature over 62°C, EDX-607 will limit the output and
decrease to 0% smoothly till the temperature below 55°C ; when it over 65°C,
EDX-607 will stop output immediately.
2-12 Display Current Load
Long holdFCNfor 3 seconds to enter function menu and then pressFCN9 times
to select the function or pressFCN+CH4_DOWNat the same time, the screen
will display the current of present load. PressENTERto exit.
2-13 Set Timer
Long holdFCNfor 3 seconds to enter function menu and then pressFCN7 times
to select the function or pressFCN+CH2_DOWNat the same time, the screen
will display the timing scene setting as
1. Add Record
STEP-1PressFCN+CH2_DOWN, the screen will display ,
”01” means the first record, pressENTERto enter the current record. If it is empty
(no record), it will display .
STEP-2Press  ▲ and ▼ to modify, press

or

to select the hour,
minute, scene(SC), fade time (Fd) and Zone(Zn).
In order to execute the scenes periodically and automatically, we advise
users to save daily-used scenes into “Timing Scene”.

ISO 9001 CERTIFIED www.liteputer.com.tw
Lite-Puter
EDX-607E [EUM-A]
16
Note: When the timer on, EDX-607 will recall the scene automatically.
STEP-3 PressENTERto save and exit.
STEP-4 If you need add more record, press

to add another record and the setting
steps as above.
2. Edit Record
Select the record number need to edit. Press ENTERto edit the current record.
The following steps are the same as adding record.
3. Delete Record
Select the record number and press 
▼ for 3 seconds to delete the record. The
screen will show as below, it means the record was deleted.
2-14 Scene Setting
PressCH1- CH6 UP/ DOWNto adjust 12 channels’ the dimming value. There are
only 6 channels displayed on the panel. PressSshift between channel 1 ~ 6 and
channel 7 ~12. EDX-607 can store 12 scenes.
Example:
1. The current defaulted channels are channel 1 to 6, pressSthe screen will
display as below.CH1- CH6 UP/ DOWNcan adjust the dimming value of channel
1 ~ 6 correspondingly.
2. PressSshift to channel 7 ~ 12, the screen will display as below.CH1- CH6 UP/
DOWNcan adjust the dimming value channel 7 ~ 12 correspondingly.

ISO 9001 CERTIFIED www.liteputer.com.tw
Lite-Puter
EDX-607E [EUM-A]
17

While edit the dimming value of channel 4, the screen will display as and the
right side of which will display the dimming value. The dimming values also showed
on the LED bar.
3. Long hold scene button for 3 seconds to save current scene. The way for save
scene 7 to scene 12 is pressSHIFT+ scene button for 3 seconds.
For example,
If save the channel setting to scene 2, the steps as below.
Long hold scene button2for 3 seconds, the screen will show , which means
storing the current setting to scene 2.
2-15 Scene Recall
Press scene buttons1~6to recall the scene 1 to scene 6 correspondingly. The
LED nearby the scene button will be lightened.
Press SHIFT+1~6to recall scene 7 to 12.
2-16 Memory & Button Lock/Unlock Function
PressFCN+SC1at the same time to lock/unlock memory keys. Press FCN
+OFFat the same time to lock/unlock all the button. In memory lock status, setting
save is useless; in button lock status, all buttons are useless.
2-17 Adjust and View Dimming Value
1.Press 

or 

to view dimming value of each channel.
If the scene was set as FADE:
Press scene button once, the scene will be call out in fade mode.
Press scene button twice quickly, the scene will call out immediately.

ISO 9001 CERTIFIED www.liteputer.com.tw
Lite-Puter
EDX-607E [EUM-A]
18
2. Press ▲ to increase all channels’ dimming value, or press ▼ to decrease all
channels’ dimming value.
3.PressENTERthe dimming value of current channel will increase or decrease at a
speed of 25%.
4.HoldDOWNbutton of current channel, and then pressUPthe current channel’
dimming value will be 0% at once. Repeat it, the dimming value of the current
channel will be 100% at once.
5.HoldUPthen pressDOWNhas the same function as step 4.
2-18 Panel LED on/off Setting
This function is to set whether LED screen be turned off after pressOFFto turn off
all channels.
STEP-1 Long holdFCNfor 3 seconds to enter function menu and then pressFCN
10 times to select the function or pressFCN+CH5_DOWNat the same
time, the screen will display the status of LED screen
STEP-2Then press ▲ to turn on LED or press ▼ to turn it off.
STEP-3PressENTERto save and exit.
Note: After turn off the LED screen, it will be turned on again if press any button.
2-19 Dimming Curve Setting
Each channel can choose one of three dimming curves.
STEP-1 Long holdFCNfor 3 seconds to enter function menu and then pressFCN
11 times to select the function or pressFCN+CH6_DOWNat the same time, the
screen will display,
STEP-2PressCH1- CH6 UP/ DOWNto choose the dimming curves of channel
1~12. The dimming curve status of each channel shows on corresponding
LED bar as below,
STEP-3PressENTERto save and exit.