Lite Source LMT-1009 User manual

OPERATION MANUAL
LMT-1009 Transmitter & LMR-400 Receiver
FEATURES:
●Simple installation, easy operation
●67 million codes, self program.
●6 memory scene settings, no memory loss forever.
●Red LED indicator on transmitter.
●Control 2 lights (main and secondary light)
●Can be controlled by transmitter and or existing house hold mechanical switch.
●Security mode.
Fig. 1
Main [I] “OFF” Button
Main [I] “ON” Button
“DELAY OFF” Button
Secondary [II] “OFF” Button
Secondary [II]“ON” Button

ON OFF ON OFF ON OFF
[I] [I] [II] [II] [I]+[II] [I]+[II]
INSTALLATION:
Receiver LMR-400 (Refer to Fig. 1)
zDisconnect main power before installation.
zConnect AC wire (Live & Neutral) to receiver block terminal IN.
zConnect Load wires into receiver block terminal OUT (Port I & Port II) .
zConnect main power on.
OPERATION :
1. Transmitter LMT-1009
(Refer to Fig. 2)
zMain [I] “ON” button: Turns on main [I] light
zMain [I] “OFF” button: Turns off main [I] light
(Refer to Fig. 3)
zSecondary [II] “ON” button: Turns on main [II] light
zSecondary [II] “OFF” button: Turns off main [II] light
z“DELAY OFF” button: Turns off automatically after 10 seconds.
z“Security mode”: Randomly turns on & off the lights.
To activate, hold both “ON and OFF” button of Main [I] for 3 seconds.
To deactivate, simply press any button on the transmitter.
※REMARK※
In order to operate with a transmitter, the mechanical switch must be powered “ON”
2. Mechanical Switch (Refer to Fig. 4)
z1st time “ON” will control the main [I] light
z2nd time “ON” will control the secondary [II] light
z3rd time “ON” will control both main [I] and secondary [II] light.
HOW TO LINK CODE:
zTo start, program transmitter with receiver.
zConnect power to receiver
zSwitch ON first then OFF and ON cycle for 6 times, this will enter learning mode.
While in learning mode, the main [I] light connected to receiver will flash to indicate ready for programming.
zThen on transmitter press the main [I] “ON” button once, main [I] and secondary [II] light will flash 2 times to indicate
programming is confirmed and completed.
！ During leaning mode if within 12 seconds no signal is detected it will automatically return to stand-by
mode.
Fig. 2 Fig. 3 Fig. 4

TO DELETE CODE :
zSwitch ON first then OFF and ON cycle for 6 times, this will enter learning mode.
While in learning mode, the main [I] light connected to receiver will flash to indicate ready for programming.
zThen on transmitter press the main [I] “OFF” button once, main [I] and secondary [II] light will flash 2 times to indicate
the memory of this transmitter is deleted.
TO DELETE ALL CODE :
zSwitch ON first then OFF and ON cycle for 6 times, this will enter learning mode.
zFollow again switching OFF and ON cycle for 6 times, main [I] and secondary [II] light will flash 2 times to indicate all
memories are deleted.
BATTERY EXCHANGE:
3V CR2032 lithium battery is included ex-factory.
When battery voltage is low, transmission is low.
Slide down the battery cover and replace a fresh new battery.
SPECIFICATION:
LMT-1009 Transmitter:
3V CR2032 BATTERY included
LMR-400 Receiver:
Frequency: 433.92MHz
Input: AC 120V
Output [I]: AC 250W max.
Output [II]: AC 250W max.
Ta: 50 ℃
Tc: 80℃
FAULT FINDING:
No activation: Check battery polarity or running out battery
Check code link successful.
Check if memory setting is full
Check correct wiring installation.
Warning!
DO NOT OVERLOAD
Disconnect main power before wiring installation.
Do not use in damp places like patios, cellar, flammable liquid, solvents, paints etc..

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.