LiteBee Electromagnet Module Y17-AI User manual

Product Manual
Electromagnet Module

Product introduction
CONTENTS
01 Brief introduction
Installation
06 Installing steps
Programming
11 Reference case
About the product
02 Packing list
02 Specification
Firmware
03 Firmware version
05 Firmware updating
1 2 3
4 5

Product introduction
The electromagnet extension is an additional accessory for LiteBee Wing. It can lift
and drop the iron materials by its electromagnet. Combined with the drone, the extension
also can be programmed to transfer the matrials automatically. This extension provides
a chance for kids to practice their programming skill and learn how the programming can
be applied.
01

Packing list Specification
Model: Y17-AI
Size: 40*40*8mm
Working voltage/current: 5V/@80mA
Size of QR code: 24*30cm
Max load: 500g
Actual load: 0-8g
Electromagnet unit*1 Counterweight holder*1 Electromagnet holder*1 Long bolt*8
Connecting cable*1 Short bolt*8 Nylon screw*2
Electromagnet*1 QR code for position*15 Adsorbate*20
Nut*2
ABOUT THE PRODUCT
02

To apply the electromagnet, the firmware version of drone and controller should be V1.1.0 and up, the version of PC
software - LiteBee Go should be V0.2.1 and up.
Description
How to check the version
Link the drone to controller Connect the controller with computer by USB cable Switch to programming mode
Start LiteBee Go
Choose “LiteBee Wing” mode
Check the version on the button line of LiteBee Go(pic 4)
Click the exclamation mark
to make sure the controller
connected(pic 3)
Click the
“Add Extension”
(pic 1)
03
PREPARATION
Firmware version
FV shows the version of the aircraft
RV shows the version of the controller

pic 1 pic 2
pic 3 pic 4 04

How to update the version
To download the corresponding document for firmware upgrading on LiteBee official web
Or, you can find relevant video for firmware upgrading on YouTube channel - LiteBee, search
“Guide for firmware upgrade”
Official Website:https://www.litebee.com/product/liteBeeWing/download
pic 5
05

Disassemble these arms of rotor；
Remove these short bolts.
Replace them by long bolt；
And then reassemble it.
Fix the electromagnet on the
holder with a screw；
Tighten the screw until it
can't twist.
1 2 *4 3*1
*1 *1 *1
06
INSTALLATION

*4 *1 *1
4 5 6
*1
07
Fix the counterwight holder
on the front；
Fix the electromagnet on
the back.
Insert 4 short bolts into the bottom
of the drone.
Insert the connecting cable into the
electromagnet unit.

7 8 9
08
Install theelectromagnet unit on the
bottom of the drone；
Attention: the blank side face to the
bottom of the drone.
Insert the cable into the broadside
of the drone.
Connect the power line with the
electromagnet unit.

Finished
09

Step 1: Connect the drone with computer
PS: If there is a green tick mark, connected; if a orange exclamation, click the
exclamation to connect again.
Link the drone with the controller first
Connect the controller with computer by USB cable
Step 2: Electromagnet mode
Start LiteBee Go
Click “Add extension”
Click “Identification card + attract and lift”
10
EXTENSION PROGRAMMING

Let the drone fly to the QR code No.0 and hover; then land and turn on the electromagnet and lift the adsorbate; take off
again and fly to the QR code No.10; hover and turn off the electromagnet to drop the adsorbate; land.
Task
图10
Case
Mind map
Start
Calibrate
Take off and fly forward
yes
yes
when recognized the
QR code No.0
Hover for 5 seconds
Autoland
Turn on the electromagnet
Take off and fly forward
When recognized the
QR code No.10
Hover for 2 seconds
Turn off the electromagnet
Autoland
11
Reference case

Manufacturer: Shenzhen Makerfire Technology Co., Ltd.
Website: www.litebee.com
Tel: [phone]
Email: [email protected]
Address: 25th Floor, A7 Building, Creative City, Liuxian Ave, Xili Street, Nanshan
District, Shenzhen, China.