LITEWAY LuxLink OC-1002 User manual

WARRANTY
All fiber optic transmission systems, products and accessories
manufactured by Liteway, Inc. and it’s subsidiaries are fully tested
prior to shipment and are warranted against defective materials
and workmanship for a period of five full years from the date of the
original shipment. Should a problem occur, a Return Material
Authorization Number (RMA) must be obtained from Liteway Inc.
at [phone] and the item returned to Liteway, Inc. 166
Haverford Road, Hicksville, NY 11801, USA, prepaid. Liteway Inc.
will then, at its option repair or replace the defective item.
Liteway, Inc. maximum liability under this warranty is limited to the
cost of the defective item only. No contingent liabilities of any kind
are either assumed or implied.
Any items returned to Liteway, Inc. that have been misused,
abused, damaged, modified, connected or adjusted in any way
contrary to the instructions furnished by Liteway, Inc. or repaired
by unauthorized personnel will not be covered by this warranty.
Any non-warranty repairs required will be quoted at the current
rate for such services.
Important Notices
CAUTION ! AVOID DIRECT EXPOSURE TO BEAM.
All -7,-8, and -9 Models use laser diodes. These solid-state laser
diodes are located in the optical ports of these units. Laser diodes
produce invisible radiation that may be harmful to human eyes.
Never look directly into the optical port of any fiber optic unit
designed to operate with single-mode optical fiber.
NOT FOR LIFE SUPPORT SYSTEMS
Liteway, Inc. does not authorize or warrant any of its products or
accessories for use in critical life support systems or applications
of any kind.
© Copyright 2017 Liteway, Inc. 106155 Rev E
OPERATING INSTRUCTIONS
LuxLink®
Fiber Optic
Optical Coupler/Splitter
Model OC-1002
The OC-1002 Fiber Optic Optical Coupler consists of a 1 x 2 optical
coupler. The unit is designed for use as an optical splitter or
combiner to implement a single-fiber bi-directional transmission
system.
Technical Specifications
Operating Wavelength 850 - 1310 (for -1, -3 models)
1310 -1550 (for -7 ,-9 models)
Fibers Accommodated Multimode (for -1, -3 models)
Single-mode (for -7, -9 models)
Optical Connectors ST (for -1, -3 models)
FC/PC (for –7 ,-9 models)
Insertion Loss Common
to or from A or B 4 dB Typical
Insertion Loss A to
from B 20 dB Minimum
Temperature Range -35º to +75ºC
Power Requirements None
Physical Size (mm) 5.0”(127)L x 1.0” (25.4)W x
3.0”(7)D
All specifications are subject to change without prior notice.
!

Installation Instructions
The OC-1002 is an optical coupler that can be utilized as power
splitter or combining bi-directional signals.
Optical Splitter Applications
When used as an optical splitter, the loss from the common port to
either port A or port B will be 4 dB typical. This means that an optical
signal transmitted into the common port will appear at ports A and B
reduced by 4 dB. An optical signal “launched” into ports A or B will
appear at the common port reduced by 4 dB. An optical signal
“launched” into port A will appear at port B attenuated by a minimum
of 20 dB.
106155 Rev E
Single-fiber bi-directional Transmission Applications
When used to implement a bi-directional transmission system signals
transmitted into port A will appear at the common port reduced by
about 4 dB. At the opposite end of the link, the signals will be
reduced by an additional 4 dB + the loss within the common fiber.
Signals transmitted into port A on the same side of the link will be
attenuated by a minimum of 20 dB at port B.
OC-1002
OC-1002 Utilized in Bi-directional Systems
Optical
Transceiver
Common Port A
Port B Rx
Tx